The evaluation board is driven with 1.2V core voltage, so system clock
must not exceed 192 MHz, bus clock must not exceed 110 MHz. Choose
appropriate values and set DTCMWAIT accordingly. Adapt UART setting to
avoid console log interruption and wait for the specified locking time
of 300us to pass.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Cc: bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If NAND is enabled we better have the include around.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add common code for MIPI-CSIS and MIPI-DSIM drivers to support
their corresponding D-PHY's enable and reset control.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Extend MIPI-CSIS driver's platform data structure with a callback
for D-PHY enable and reset control. Also add a flag indicating
whether the external MIPI-CSI (VDD18_MIPI) power supply should
be managed in the driver through the "vdd" power supply. On some
boards this regulator may be a fixed voltage regulator without
an inhibit function.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add functions for configuration of the parallel camera
bus pins on S5PV210 and Exynos4 SoC.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The HW superwised smart idle for wdtimer in OMAP3 prevents
CORE power domain idle transitions. Disable it by swithing
to SW supervised transitions.
This could be a hardware bug in the OMAP3 wdtimer2 block.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
This is a first pass at reorganizing mach-omap2/voltage.c:
- Separate almost all of the data from the code of mach-omap2/voltage.c.
The code remains in mach-omap2/voltage.c. The data goes into one
of several places, depending on what type of data it is:
- Silicon process/validation data: mach-omap2/opp*_data.c
- VC (Voltage Controller) data: mach-omap2/vc*_data.c
- VP (Voltage Processor) data: mach-omap2/vp*_data.c
- Voltage domain data: mach-omap2/voltagedomains*_data.c
The ultimate goal is for all this data to be autogenerated, the same
way we autogenerate the rest of our data.
- Separate VC and VP common data from VDD-specific VC and VP data.
- Separate common voltage.c code from SoC-specific code; reuse common code.
- Reorganize structures to avoid unnecessary memory loss due to unpacked
fields.
There is much left to be done. VC code and VP code should be separated out
into vc*.c and vp*.c files. Many fields in the existing structures are
superfluous, and should be removed. Some code in voltage.c seems to be
duplicated; that code should be moved into functions of its own. Proper
voltage domain code should be created, as was done with the powerdomain
and clockdomains, and powerdomains should reference voltagedomains.
Thanks to Shweta Gulati <shweta.gulati@ti.com> for comments. Thanks
to Rajendra Nayak <rnayak@ti.com> for finding and fixing some bugs
that prevented OMAP4 from booting:
https://patchwork.kernel.org/patch/587311/
His patch has been folded into this one to avoid breaking OMAP4
between patches. Thanks also to Kevin Hilman <khilman@ti.com> for
finding and fixing a compile problem when !CONFIG_PM:
http://www.spinics.net/lists/arm-kernel/msg118067.html
His patch has also been folded into this one to avoid breaking
!CONFIG_PM builds.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Shweta Gulati <shweta.gulati@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
The Multi-Core Timer(MCT) of EXYNOS4 is designed for implementing
clock source timer and clock event timers. This patch implements
1 clock source timer with 64 bit free running counter of MCT and
2 clock event timers with two of 31-bit tick counters.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds IRQ_MCT_G0 to irq map. IRQ_MCT_G0 is an interrupt
of MCT comparator and used for kernel global timer.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The MCT(Multi-Core Timer) is used for implementing kernel timers
for EXYNOS4210.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On the newer ARM processors like CortexA8, CortexA9, the caches can be
speculatively loaded while they are getting flushed.
Clear the SCTLR C bit to prevent further data cache allocation as
part of cache clean routine
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The current code saves few un-necessary registers which are read-only or
write-only, unused CP15 registers.
Remove them and keep only necessary CP15 registers part of
low power context save/restore.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
When L1 cache is suppose to be lost, it needs to be cleaned before
entrering to the low power mode.
While at this, also fix few comments and remove un-necessary
clean_l2 lable.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add necessary barriers after enabling MMU. Also use the sane way to
load pc and jump to it instead of executing ldma first up.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On ARMv7 dsb, dmb instructions are supported and can be used directly
instead of their cp15 equivalnet. Also remove the opcodes for smc
and use the available instruction directly in OMAP3 low power asm code
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
When we're interrupted on the secure side, we should just issue
another smc instruction again instead of replaying the arguments
to smc. Fix it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Assign the registers used in the inline assembly immediately
before the inline assembly block. This ensures the compiler
doesn't optimize away dead register assignments when it
shouldn't.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: David Brown <davidb@codeaurora.org>
We don't want the compiler to remove these asm statements or
reorder them in any way. Mark them as volatile to be sure.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
There should be no reason to call h4_init_flash this
early. It causes problems as things are not yet initialized.
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Various binutils versions can resolve Thumb-2 branches to
locally-defined, preemptible global symbols as short-range "b.n"
branch instructions.
This is a problem, because there's no guarantee the final
destination of the symbol, or any candidate locations for a
trampoline, are within range of the branch. For this reason, the
kernel does not support fixing up the R_ARM_THM_JUMP11 (102)
relocation in modules at all, and it makes little sense to add
support.
The symptom is that the kernel fails with an "unsupported
relocation" error when loading some modules.
Until fixed tools are available, passing
-fno-optimize-sibling-calls to gcc should prevent gcc generating
code which hits this problem, at the cost of a bit of extra runtime
stack usage in some cases.
The problem is described in more detail at:
https://bugs.launchpad.net/binutils-linaro/+bug/725126
Only Thumb-2 kernels are affected.
This patch adds a new CONFIG_THUMB2_AVOID_R_ARM_THM_JUMP11 config
option which adds -fno-optimize-sibling-calls to CFLAGS_MODULE
when building a Thumb-2 kernel.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adding Thumb2 support to the runtime patching of the virt_to_phys and
phys_to_virt opcodes.
Tested both the 8-bit and the 16-bit fixups, using different placements
in memory to exercize all code paths.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The removal of the single-step emulation from ptrace on ARM means that
thread_struct no longer has software breakpoint fields in its debug
member.
This patch fixes the a.out core dump code so that the debug registers
are zeroed rather than trying to copy from non-existent fields.
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some cards have the CRC errors in read on mx51 BBG board.
Configure the eSDHC pad configurations to level up the
compatibility to fix this issue.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This saves some power. OMAP4 version should check for GPT module ID, as
autoidle is only supported on a subset of these.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add a new clockdomain flag, CLKDM_NO_AUTODEPS, which, when marked on a
clockdomain, will prevent "autodeps" from being associated with the
clockdomain. ("Autodeps" are sleep dependencies and wakeup
dependencies from/to processor modules that are automatically added to
a clockdomain when it is in hardware-supervised idle mode. They are
deprecated -- a relic from the old CDP trees -- but are still in use
for OMAP3.)
Also, prevent the hwmod code from adding or removing initiator
dependencies for clockdomains with this flag set.
This patch should allow others to test which clockdomains actually
still need autodeps.
Thanks to Kevin Hilman <khilman@ti.com> for noting that the original
version should also modify the hwmod code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Create a new API that forms a wrapper to _set_module_autoidle()
to modify the AUTOIDLE bit.
This API is intended to be used by drivers that requires direct
manipulation of the AUTOIDLE bits in SYSCONFIG register.
McBSP driver requires autoidle bit to be enabled/disabled while
using sidetone feature.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: restrict the hwmod states that the autoidle bit can be changed
in; changed function name; dropped "int" from "unsigned int long"]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some boards can't tolerate IP blocks being reset when they are initialized.
Michael Büsch cites a case with the Nokia N810:
http://www.spinics.net/lists/linux-omap/msg47277.html
To allow such boards to continue working normally, allow board file
maintainers to mark IP blocks to prevent them from being reset upon
init. This is done via a hwmod function, omap_hwmod_no_setup_reset().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Michael Buesch <mb@bu3sch.de>
On OMAP2 and OMAP3 the reset ctrl shift doesn't match the
status bit, as it does on OMAP4, when handling the reset lines.
This patch adds a new member in the reset info structure, so now it
can be added as part of hwmod data, and checked accordingly for
OMAP2 or 3; otherwise, there could be cases when the shift masks
doesn't match both of the registers, and a successful reset might
throw an error message or vice versa.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
[paul@pwsan.com: added a warning if st_shift used on OMAP4; renamed 'r'
variable; improved some documentation]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
_init_clock always returns 0 and does
not propogate the error (in case of failure)
back to the caller, causing _init_clocks to
fail silently.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some of the omap2, omap3 peripherals support software reset. This
can be done through the softreset bit in sysconfig register.
The reset status can be checked through resetdone bit of
sysstatus register. syss_has_reset_status is added to the hwmod
database of peripherals which have resetdone bit in sysstatus register.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Reviewed-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Autoidle is a single bit, TIOCP_CFG[0], setting on OMAP1/2/3/4 platforms.
In _set_module_autoidle() I am seeing 0x3 value where the mask is computed.
This should be 0x1.
v2:
(1) Modified the subject.
(2) Modified the description with further specific information.
Baseline:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
Tested Info:
Boot tested on OMAP 1/2/3/4.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Master ports from interconnect are generating some annoying circular
references that become tricky to handle if we have to dynamically
remove some IP on some variant platforms.
Since they are not used for the moment, and since we can still build
that relation using the reverse relation (slave port from the IP
toward master port of the interconnect), let remove them for the
moment like it is done on OMAP4.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Sanjeev Premi <premi@ti.com>
Most likely, the LCD panel on mx28 platform will require a pixel
clock higher than ref_xtal_clk (24 MHz), so the patch initializes
the parent of lcdif clock as ref_pix_clk.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use the correct I/O address definitions for Footbridge
peripherals when the kernel is compiled without MMU
support.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit d344272671 ("OMAP3: PM: Adding
smartreflex hwmod data") added data that claims that the L4 CORE has
two slave interfaces that originate from the SmartReflex modules,
omap3_l4_core__sr1 and omap3_l4_core__sr2. But as those two data
structure records show, it's L4 CORE that has a master port towards
SR1 and SR2.
Move the incorrect data from slaves list to master list.
Based on a path by Paul Walmsley <paul@pwsan.com>
https://patchwork.kernel.org/patch/623171/
That is based on a patch by Benoît Cousson <b-cousson@ti.com>:
https://patchwork.kernel.org/patch/590561/
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Cc: Sanjeev Premi <premi@ti.com>
Cc: Thara Gopinath <thara@ti.com>
These warnings are missing newlines and spaces causing confusing
looking output when they trigger.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
if building kernels without OMAP2 support, we
will see a warning such as:
arch/arm/mach-omap2/io.c: In function 'omap2_init_common_infrastructure':
arch/arm/mach-omap2/io.c:389:3: warning: statement with no effect
arch/arm/mach-omap2/io.c:391:3: warning: statement with no effect
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
