When using CONFIG_IXP4XX_INDIRECT_PCI, we run into a recursive
header file dependency between mach/io.h and asm/pci.h, resulting
in a build failure:
mach-ixp4xx/include/mach/io.h: In function 'is_pci_memory':
mach-ixp4xx/include/mach/io.h:53:18: error: 'PCIBIOS_MIN_MEM' undeclared (first use in this function)
return (addr >= PCIBIOS_MIN_MEM) && (addr <= 0x4FFFFFFF);
^
mach-ixp4xx/include/mach/io.h:53:18: note: each undeclared identifier is reported only once for each function it appears in
We can work around this by referencing the pcibios_min_mem variable
directly through an extern declaration, rather than using the macro.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
The omixp board code unconditionally defines a gpio-led
device, but for some reason includes the header file
for this only if CONFIG_LEDS_CLASS is enabled, causing
a build error otherwise.
Removing the #ifdef fixes the build error with no downsides
whatsoever.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
The hisi SMP code always uses the hi3xxx_set_cpu() function
defined in the hotplug.c file, so we cannot build without
this when CONFIG_SMP is enabled. This patch slightly restructures
the code so we always build the parts of hotplug.c that we need
but just leave out the CPU disable logic if CONFIG_HOTPLUG_CPU
is turned off.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
ep93xx_chip_revision is used by the pata_ep93xx driver,
which can be a loadable module. Exporting the symbol
avoids a link error in this case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
The efm32 platform does not provide a zreladdr-y line its Makefile.boot,
so we always have to use CONFIG_AUTO_ZRELADDR in order to successfully
build and link a zImage.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Uwe Kleine-König <kernel@pengutronix.de>
The DAVINCI_DA850_EVM board uses an unusual method to
enable the GPIO_PCA953X and KEYBOARD_GPIO_POLLED symbols,
which leads to the dependencies on these symbols being
ignored. As GPIO_PCA953X actually requires I2C, that
can lead to build failures when I2C is disabled.
This patch removes the duplicate symbol definitions
and instead enables them from the davinci_all_defconfig
file.
A different question whether we actually want to automatically
enable them at all or rather put them into defconfig,
but that should be a separate patch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: davinci-linux-open-source@linux.davincidsp.com
We cannot call phy_register_fixup_for_uid() if CONFIG_PHYLIB
is not built into the kernel, and we should not enforce that
to be built into vmlinux either, because one might want to
disable the entire network stack.
This change uses a compile-time condition on CONFIG_PHYLIB
to remove the call in the cases where it cannot work.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: davinci-linux-open-source@linux.davincidsp.com
It makes no sense for sama5 support to be enabled if we don't
also enable USE_OF. Making this automatic in Kconfig avoids
a possible randconfig conflict between the old and new clock
support code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
If CONFIG_PATA_AT91 is disabled, the code in at91_add_device_cf
is turned into invalid C statements due to the lack of an
expression before the 'else' clause.
This moves the first half of the condition inside of the #ifdef,
which seems to be what the author intended.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
The pata_at91 driver uses interfaces defined in the sam9_smc
platform code. Since the pata driver can be a loadable module,
we have to export those symbols in order to link cleanly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
at91x40 has no support for device tree, but Kconfig allows
us to enable CONFIG_OF anyway, causing a link error in the
at91 reset controller initialization.
The easiest fix is to adapt the existing #ifdef to omit
the broken code on at91x40 where it is never called anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
at91x40 is different from all the other at91 machines, and it is
impossible to build a kernel that works on both this SoC and
any of the others, even though it is possible to build a noMMU
kernel for any at91 machine.
By turning at91x40 into a separate top-level option, we explicitly
forbid enabling invalid configurations that include mutually exclusive
machines.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
I originally wrote commit 35bb4399bd to shrink the size of the overhead of
tracepoints by several kilobytes. Later, I received a patch from Vaibhav
Nagarnaik that fixed a bug in the same code that this commit touches. Not
only did it fix a bug, it also removed code and shrunk the size of the
overhead of trace events even more than this commit did.
Since this commit is scheduled for 3.15 and Vaibhav's patch is already in
mainline, I need to revert this patch in order to keep it from conflicting
with Vaibhav's patch. Not to mention, Vaibhav's patch makes this patch
obsolete.
Link: http://lkml.kernel.org/r/20140320225637.0226041b@gandalf.local.home
Cc: Vaibhav Nagarnaik <vnagarnaik@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* acpi-processor:
ACPI: Move BAD_MADT_ENTRY() to linux/acpi.h
ACPI / processor: Make it possible to get APIC ID via GIC
ACPI / processor: Build idle_boot_override on x86 and ia64
ACPI / processor: Use ACPI_PROCESSOR_DEVICE_HID instead of "ACPI0007"
ACPI / processor: Fix acpi_processor_eval_pdc() return value type
Add REQ_SYNC early, so rq_dispatched[] in blk_mq_rq_ctx_init
is set correctly.
Signed-off-by: Shaohua Li<shli@fusionio.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Add a new blk_mq_end_io_partial function to partially complete requests
as needed by the SCSI layer. We do this by reusing blk_update_request
to advance the bio instead of having a simplified version of it in
the blk-mq code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
It's almost identical to blk_mq_insert_request, so fold the two into one
slightly more generic function by making the flush special case a bit
smarted.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
I'm transitioning maintainership of the xHCI driver to my colleague,
Mathias Nyman. The xHCI driver is in good shape, and it's time for me
to move on to the next shiny thing. :)
There's a few known outstanding bugs that we have plans for how to fix:
1. Clear Halt issue that means some USB scanners fail after one scan
2. TD fragment issue that means USB ethernet scatter-gather doesn't work
3. xHCI command queue issues that cause the driver to die when a USB
device doesn't respond to a Set Address control transfer when another
command is outstanding.
4. USB port power off for Haswell-ULT is a complete disaster.
Mathias is putting the finishing touches on a fix for #3, which will
make it much easier to craft a solution for #1. Dan William has an
ACKed RFC for #4 that may land in 3.16, after much testing. I'm working
with Mathias to come up with an architectural solution for #2.
I don't foresee very many big features coming down the pipe for USB
(which is part of the reason it's a good time to change now). SSIC is
mostly a hardware-level change (perhaps with some PHY drivers needed),
USB 3.1 is again mostly a hardware-level change with some software
engineering to communicate the speed increase to the device drivers, add
new device descriptor parsing to lsusb, but definitely nothing as big as
USB 3.0 was.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@intel.com>
There's only one caller, which is a straight wrapper and fits the naming
scheme of the related functions a lot better.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
After the previous patches, an interrupt whose bit is set in the IRR
register will never be in the LAPIC's IRR and has never been injected
on the migration source. So inject it on the destination.
This fixes migration of Windows guests without HPET (they use the RTC
to trigger the scheduler tick, and lose it after migration).
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This git patch adds x86_64 AVX2 optimization of SHA1
transform to crypto support. The patch has been tested with 3.14.0-rc1
kernel.
On a Haswell desktop, with turbo disabled and all cpus running
at maximum frequency, tcrypt shows AVX2 performance improvement
from 3% for 256 bytes update to 16% for 1024 bytes update over
AVX implementation.
This patch adds sha1_avx2_transform(), the glue, build and
configuration changes needed for AVX2 optimization of
SHA1 transform to crypto support.
sha1-ssse3 is one module which adds the necessary optimization
support (SSSE3/AVX/AVX2) for the low-level SHA1 transform function.
With better optimization support, transform function is overridden
as the case may be. In the case of AVX2, due to performance reasons
across datablock sizes, the AVX or AVX2 transform function is used
at run-time as it suits best. The Makefile change therefore appends
the necessary objects to the linkage. Due to this, the patch merely
appends AVX2 transform to the existing build mix and Kconfig support
and leaves the configuration build support as is.
Signed-off-by: Chandramouli Narayanan <mouli@linux.intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The crypto algorithm modules utilizing the crypto daemon could
be used early when the system start up. Using module_init
does not guarantee that the daemon's work queue is initialized
when the cypto alorithm depending on crypto_wq starts. It is necessary
to initialize the crypto work queue earlier at the subsystem
init time to make sure that it is initialized
when used.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
(struct caam_ctx) ctx->key_dma needs to be unmapped
when context is cleaned up.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add test vectors for aead with null encryption and md5,
respectively sha1 authentication.
Input data is taken from test vectors listed in RFC2410.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These defines might be needed by crypto drivers.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 61bb86bba1
("crypto: caam - set descriptor sharing type to SERIAL")
changed the descriptor sharing mode from SHARE_WAIT to SHARE_SERIAL.
All descriptor commands that handle the "ok to share" and
"error propagation" settings should also go away, since they have no
meaning for SHARE_SERIAL.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The ahash_def_finup() can make use of the request save/restore functions,
thus make it so. This simplifies the code a little and unifies the code
paths.
Note that the same remark about free()ing the req->priv applies here, the
req->priv can only be free()'d after the original request was restored.
Finally, squash a bug in the invocation of completion in the ASYNC path.
In both ahash_def_finup_done{1,2}, the function areq->base.complete(X, err);
was called with X=areq->base.data . This is incorrect , as X=&areq->base
is the correct value. By analysis of the data structures, we see the areq is
of type 'struct ahash_request' , areq->base is of type 'struct crypto_async_request'
and areq->base.completion is of type crypto_completion_t, which is defined in
include/linux/crypto.h as:
typedef void (*crypto_completion_t)(struct crypto_async_request *req, int err);
This is one lead that the X should be &areq->base . Next up, we can inspect
other code which calls the completion callback to give us kind-of statistical
idea of how this callback is used. We can try:
$ git grep base\.complete\( drivers/crypto/
Finally, by inspecting ahash_request_set_callback() implementation defined
in include/crypto/hash.h , we observe that the .data entry of 'struct
crypto_async_request' is intended for arbitrary data, not for completion
argument.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The functions to save original request within a newly adjusted request
and it's counterpart to restore the original request can be re-used by
more code in the crypto/ahash.c file. Pull these functions out from the
code so they're available.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add documentation for the pointer voodoo that is happening in crypto/ahash.c
in ahash_op_unaligned(). This code is quite confusing, so add a beefy chunk
of documentation.
Moreover, make sure the mangled request is completely restored after finishing
this unaligned operation. This means restoring all of .result, .base.data
and .base.complete .
Also, remove the crypto_completion_t complete = ... line present in the
ahash_op_unaligned_done() function. This type actually declares a function
pointer, which is very confusing.
Finally, yet very important nonetheless, make sure the req->priv is free()'d
only after the original request is restored in ahash_op_unaligned_done().
The req->priv data must not be free()'d before that in ahash_op_unaligned_finish(),
since we would be accessing previously free()'d data in ahash_op_unaligned_done()
and cause corruption.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Found by the kbuild test robot, the first argument to caam_init_rng
has a spurious ampersand.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The maximum number for irq routes is currently 1024, which is a bit on
the small size for s390: We support up to 4 x 64k virtual devices with
up to 64 queues, and we need one route for each of the queues if we want
to operate it via irqfd.
Let's bump this to 4k on s390 for now, as this at least covers the saner
setups.
We need to find a more general solution, though, as we can't just grow
the routing table indefinitly.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Introduce a new interrupt class for s390 adapter interrupts and enable
irqfds for s390.
This is depending on a new s390 specific vm capability, KVM_CAP_S390_IRQCHIP,
that needs to be enabled by userspace.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Add a new interface to register/deregister sources of adapter interrupts
identified by an unique id via the flic. Adapters may also be maskable
and carry a list of pinned pages.
These adapters will be used by irq routing later.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Allow KVM_ENABLE_CAP to act on a vm as well as on a vcpu. This makes more
sense when the caller wants to enable a vm-related capability.
s390 will be the first user; wire it up.
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Fix double words "the the" in various files
within Documentations.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When igb_set_interrupt_capability() calls
igb_reset_interrupt_capability() (e.g., because CONFIG_PCI_MSI is unset),
num_q_vectors has been set but no vector has yet been allocated.
igb_reset_interrupt_capability() will then call igb_reset_q_vector,
which assumes that the vector is allocated. As this is not the case, we
are accessing a NULL-pointer.
This patch fixes it by checking that q_vector is indeed different from
NULL.
Fixes: 02ef6e1d0b (igb: Fix queue allocation method to accommodate changing during runtime)
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
82575 has only software timestamping capability and it has
no PTP Hardware Clocks. Therefore, -1 has to be specified
to the phc_index for ethtool's get_ts_info, otherwise a wrong
value will be set to the phc_index.
v2: move the if (adapter->ptp_clock) section specifying phc_index
to above the switch statement as suggested by Matthew Vick.
adapter->ptpclock will always be NULL for 82575.
Signed-off-by: Ken ICHIKAWA <ichikawa.ken@jp.fujitsu.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a memory leak in the igb_get_module_eeprom() error handling path.
Detected by Coverity: CID 1016508.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the SIOCGHWTSTAMP ioctl which enables user
processes to read the current hwtstamp_config settings
non-destructively. Previously a process had to be privileged and could
only set values, it couldn't return what is currently set without
possibly overwriting the value.
This patch adds support for this new operation into igb by keeping a
shadow copy of the config in the adapter structure, which is returned
upon request.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Additional checks are needed for a detected removal not to cause
problems. Some involve simply avoiding a lot of stuff that can't
do anything good, and also cases where the phony return value can
cause problems. In addition, down the adapter when the removal is
sensed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prevent writes to an adapter that has been detected as removed
by a previous failing read.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We will reuse it to process a nonzero IRR that is passed to KVM_SET_IRQCHIP.
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This ensures that IRR bits are set in the KVM_GET_IRQCHIP result only if
the interrupt is still sitting in the IOAPIC. After the next patches, it
avoids spurious reinjection of the interrupt when KVM_SET_IRQCHIP is
called.
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Check all register reads for adapter removal by checking the status
register after any register read that returns 0xFFFFFFFF. Since the
status register will never return 0xFFFFFFFF unless the adapter is
removed, such a value from a status register read confirms the
removal. Since this patch adds so much to ixgbe_read_reg, stop
inlining it, to reduce driver bloat.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commonize the handling of masking, which was absent for kvm_ioapic_set_irq.
Setting remote_irr does not need a separate function either, and merging
the two functions avoids confusion.
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make the ethtool register test use the normal register accessor
functions. Also eliminate macros used for calling register test
functions to make error exits clearer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
