The **rdev of 'struct bcm590xx_reg' isn't used anywhere in the driver so
remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the controls and DAPM widgets and routes.
This on one hand makes the code a bit cleaner and on the other hand
the board level DAPM elements get registered in the card's DAPM context rather
than in the CODEC's DAPM context.
The mfld_machine driver is a bit special in that it directly writes to one of
the CODEC registers from one of the control handlers. Previous to this patch it
was able to get a pointer to the CODEC from the control, since the control was
registered with the CODEC. This won't be possible anymore once the control is
registered with the card. Since there are already global variables in the driver
accessed in the same function the patch adds a global variable that holds a
pointer to the CODEC and uses that.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
After the following commit:
commit b75ef8b44b
Author: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Date: Wed Aug 10 15:18:39 2011 -0400
Tracepoint: Dissociate from module mutex
The following functions became unnecessary:
- tracepoint_probe_register_noupdate,
- tracepoint_probe_unregister_noupdate,
- tracepoint_probe_update_all.
In fact, none of the in-kernel tracers, nor LTTng, nor SystemTAP use
them. Remove those.
Moreover, the functions:
- tracepoint_iter_start,
- tracepoint_iter_next,
- tracepoint_iter_stop,
- tracepoint_iter_reset.
are unused by in-kernel tracers, LTTng and SystemTAP. Remove those too.
Link: http://lkml.kernel.org/r/1395379142-2118-2-git-send-email-mathieu.desnoyers@efficios.com
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The correct way to set multiple bits settings is always clear these
bit fields before set new settings.
Current code does not cause problem because the reset value of these
bit fields are 0, and these settings only set once during probe.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
I've been working on USB for seven years at Intel, and it's time for a
change of pace. I'm pleased to announce that I'll be joining the Intel
OTC ChromeOS team, where I'll get to learn and play with everything
across the entire Linux stack, from kernel to graphics to browser
technologies. (I'm a secret adventure/indie/casual gamer, so I'm super
excited to start working on graphics features for ChromeOS.)
I'm leaving the xHCI driver in Mathias Nyman's capable hands. I'll
still be around to answer any architectural questions or triage really
tough bugs, but I expect to ramp down on xHCI driver work in the coming
weeks.
I'll be available to answer xHCI questions until I start my 8-week
sabbatical on May 8th. I'll be doing a National Parks road trip, and
it's unlikely I'll have cell coverage. And, let's face it, people are
supposed to ignore work email on sabbaticals. :)
After my sabbatical ends on July 7th, I'll be focusing my time fully on
ChromeOS. It's been great working with and learning from Greg, Alan,
Oliver, and Felipe, but it's time to move onto my next adventure.
So long, and thanks for all the fishes!
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=eb44da0b3aa0105cb38d81c5747a8feae64834be
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=0I4N
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-adventure' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Maintainership change for 3.15.
I've been working on USB for seven years at Intel, and it's time for a
change of pace. I'm pleased to announce that I'll be joining the Intel
OTC ChromeOS team, where I'll get to learn and play with everything
across the entire Linux stack, from kernel to graphics to browser
technologies. (I'm a secret adventure/indie/casual gamer, so I'm super
excited to start working on graphics features for ChromeOS.)
I'm leaving the xHCI driver in Mathias Nyman's capable hands. I'll
still be around to answer any architectural questions or triage really
tough bugs, but I expect to ramp down on xHCI driver work in the coming
weeks.
I'll be available to answer xHCI questions until I start my 8-week
sabbatical on May 8th. I'll be doing a National Parks road trip, and
it's unlikely I'll have cell coverage. And, let's face it, people are
supposed to ignore work email on sabbaticals. :)
After my sabbatical ends on July 7th, I'll be focusing my time fully on
ChromeOS. It's been great working with and learning from Greg, Alan,
Oliver, and Felipe, but it's time to move onto my next adventure.
So long, and thanks for all the fishes!
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=eb44da0b3aa0105cb38d81c5747a8feae64834be
Since commit ca5d1b3524
"regulator: helpers: Modify helpers enabling multi-bit control",
we can set enable_val setting for device that use multiple bits for control.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This regulator is used for system IO and is fixed to 1.8V. Let's give
consumers the option to fetch the voltage level.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
You cannot mark these parameters as __initdata.
Otherwise the data is gone upon module exit.
Fixes:
[ 172.045465] BUG: unable to handle kernel paging request at ffffffffa001db38
[ 172.046020] IP: [<ffffffff81067aa4>] destroy_params+0x24/0x50
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
CONFIG_NEON is meant to be user-selectable. Turning it on
unconditionally means we can't build a smaller kernel when
we don't need it, and causes build errors if CONFIG_VFP
is not also enabled.
To still have neon enabled however, we need to turn it on
now in multi_v7_defconfig and mvebu_v7_defconfig.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The SCU code does not build unless we are compiling
an SMP kernel. This does the same as every other
platform with an SCU.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
efm32 has no mach/uncompress.h, but we can trivially use
the fallback to the ll_debug code by just allowing this
option in Kconfig.
Found during randconfig testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Uwe Kleine-König <kernel@pengutronix.de>
Fix printk format warning by using %p extension 'ad' for dma_addr_t.
drivers/spi/spi-atmel.c:1228:3: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t' [-Wformat]
drivers/spi/spi-atmel.c:1228:3: warning: format '%x' expects argument of type 'unsigned int', but argument 9 has type 'dma_addr_t' [-Wformat]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
After the restructuring of the module.h and init.h headers,
we now need to include this explicitly here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
The exynos4_l2x0_cache_init function tries to flush the data cache
for the location of the saved l2x0 registers and pass the physical
address to the s5p-sleep implementation.
However, the s5p-sleep code is optional, and if it is disabled,
we get a linker error here when the l2x0_regs_phys variable does
not exist.
To solve this, use a compile-time conditional to drop this code
if we don't want it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
The Samsung pm_check code uses the crc32 library code, which can
be built as a loadable module, in which case we get a link error
building the kernel.
A better solution is to use 'select CRC32', which is what all
other users of this code do, as it ensures it is always built-in.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Most of the Samsung platforms do not yet allow building with
DT at all, so we should select CONFIG_ATAGS for now in all
cases we also select CONFIG_SAMSUNG_ATAGS.
Found during randconfig testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
The suspend debug code for Samsung has multiple dependencies
that we should not unconditionally enable. In particular,
we rely on the DEBUG_S3C_UART setting, which in turn depends
on the samsung UART driver.
Signed-off-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
If CONFIG_SERIAL_SAMSUNG is disabled, we run into build errors
with some samsung platforms. This adds a couple of #ifdef
statements to hopefully deal with this more gracefully.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Building MACH_TORBRECK by itself results in a build error
because we try to reference the s3c_device_cfcon definition
that is hidden inside CONFIG_SAMSUNG_DEV_IDE. This changes
the Kconfig logic to ensure that option is enabled when we
need it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
The s5p64x0 platform supports two distinct SoCs, s5p6440 and s5p6450,
and in the normal configuration, both are enabled. However if we build
a kernel that only enables one of the two, the #ifdef logic in common.c
breaks down, as some of the functions declared in the header are defined
to NULL using the preprocessor but then defined anyway.
This patch cleans up the mess and ensures that each function has either
exactly one C declaration and one matching C definition, or we have
a NULL defined function pointer but no C definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
The power domain code is only available when CONFIG_PM
is enabled, so we must not select that unconditionally for
s3c64xx. Changing it to 'select PM_GENERIC_DOMAINS if PM'
mirrors what we do on other platforms, and fixes a possible
randconfig build bug.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
This board uses both MMC controllers, so we need to enable
the Kconfig option to define the platform data.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
The osiris-dvs driver calls functions exported by the tps65010
driver, so we have to ensure that driver is enabled first.
Using 'select' here doesn't work all that well, because it
requires I2C to be enabled in turn.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The gta02 has always been broken in the case when CONFIG_PCF50633_ADC
is not used, since gta02_charger_worker then passes a nonexisting
variable into the pcf50633_mbc_usb_curlim_set() function.
This addresses the obvious typo by using the variable that is
used everywhere else in this file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
If I2C is disabled, we cannot build the AT24 driver, so we
should not select it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Building the integrator platform without TTY support currently
results in a build failure because we always turn on the
pl010 or pl011 drivers. Changing this to a conditional 'select'
statement enables us to build more random configurations, although
it should have little impact for practical configurations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Commit b713aa0b15 "ARM: fix asm/memory.h build error" broke some
configurations on mach-realview with sparsemem enabled, which
is missing a definition of PHYS_OFFSET:
arch/arm/include/asm/memory.h:268:42: error: 'PHYS_OFFSET' undeclared (first use in this function)
#define PHYS_PFN_OFFSET ((unsigned long)(PHYS_OFFSET >> PAGE_SHIFT))
arch/arm/include/asm/dma-mapping.h:104:9: note: in expansion of macro 'PHYS_PFN_OFFSET'
return PHYS_PFN_OFFSET + dma_to_pfn(dev, *dev->dma_mask);
An easy workaround is for realview to define PHYS_OFFSET itself,
in the same way we define it for platforms that don't have a private
__virt_to_phys function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
The global screen_info structure is used to communicate
data about the console from platform code to the console
driver, but is only defined on ARM if either the VGA or
dummy consoles are in use.
This changes the footbridge code so we don't try to access
this structure in case it is not defined, which prevents
a possible randconfig build error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
The dc21285.c source file cannot be built when CONFIG_PCI is
disabled, because it calls a number of PCI core interfaces.
This changes the Makefile so we don't include this file in the
build if CONFIG_PCI is disabled. No other code references anything
defined inside of this file in this case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
The ARCH_EBSA285_ADDIN platform does not provide the
ISA_DMA API, which is required by the floppy driver.
Let's ensure that the floppy code can only be built
when ISA_DMA is also enabled, by moving the select
statement into ARCH_EBSA285_HOST.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
ARCH_RPC no longer supports other CPUs aside from StrongARM110,
so we can make the option implicitly selected by the platform
and no longer give the option of building a kernel without CPU
support.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
The trizeps4 and trizeps4wl platforms are both implemented
using the same board file. Since the trizeps4wl code is a
superset of trizeps4, it makes no sense to enable just the
latter, but with the current Kconfig logic, it causes the
board file not to be built at all.
Selecting MACH_TRIZEPS4 from MACH_TRIZEPS4WL ensures that
we are actually building the board file.
Found during randconfig testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Mack <zonque@gmail.com>
The Arcom/Eurotech VIPER SBC enables the I2C_GPIO driver, but
that has a dependency on I2C, and causes build failures if I2C
is disabled. To keep existing configurations running while fixing
the randconfig problems, this changes the logic to only enable
I2C_GPIO if I2C is already enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Daniel Mack <zonque@gmail.com>
balloon3_udc_init() tries to register a balloon3_gpio_vbus
device, but this has never been defined in the mainline
kernel. To avoid the obvious build failure when this function
is enabled, remove the bogus reference here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Mack <zonque@gmail.com>
The functions declared in include/linux/pxa2xx_ssp.h are
defined in plat-pxa/ssp.c, which can also be built for
PLAT_MMP, but may be disabled there. This can lead to
both unresolved symbols at link time and to duplicate
symbols at compile time for random configurations.
Changing the #ifdef in the header file to match the
Kconfig symbol that decides if the file is built solves
both problems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Mack <zonque@gmail.com>
The colibri_ohci_init function performs a register access through
the io_p2v() macro, which requires the IOMEM macro to be defined.
By explicitly including the asm/io.h header file that contains
this macro, we avoid the build error:
arch/arm/mach-pxa/colibri-evalboard.c: In function 'colibri_ohci_init':
arch/arm/mach-pxa/colibri-evalboard.c:68:2: error: implicit declaration of function 'IOMEM' [-Werror=implicit-function-declaration]
UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE;
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Mack <zonque@gmail.com>
The SAAR and TAVOREVB machines try to call functions from
the PXAFB frame buffer driver from their platform code,
which only works if that driver is built-in.
This patch ensures that both the generic frame buffer
code and the specific pxafb driver are always enabled
when we build a kernel for one of the two boards.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Mack <zonque@gmail.com>
We normally don't hard-enable Kconfig options just because
a board contains a specific piece of hardware. In this case,
selecting SMC91X causes a build error, if we don't also enable
basic network device driver support.
Since the platform has no direct dependency on this driver
at link time, we can just remove the 'select' statement.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Mack <zonque@gmail.com>
The D-Link DNS-323 machine tries to unconditionally select CONFIG_PHYLIB,
but that has other dependencies that might not necessarily be enabled,
causing random build errors.
To work around this, this patch removes the 'select' statement and
instead uses a compile-time check to skip the phy_register_fixup_for_uid()
call if PHYLIB is not available in the kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The definition for SIGBUS may not be visible without including
linux/signal.h, as I found during randconfig testing.
Adding an explicit include is certainly the right thing to do.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The code for h2 and osk implicitly assumes that the tps65010
driver is built-in, in order to perform the initial regulator
setup.
This is fine for most real uses, but it does get into the way
of build testing with 'make randconfig', since we don't want
platforms to implicitly select device drivers and subsystems
such as I2C.
This patch by contrast changes the board files to not call
into the tps65010 driver when that is not built-in, allowing
us to build all configurations including some that will not
work properly on this hardware.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
If CONFIG_OMAP_32K_TIMER isn't enabled, we will
try to use enable_dyn_sleep which wasn't defined
anywhere.
In order to fix the problem, we always define
enable_dyn_sleep as 0 when !CONFIG_OMAP_32K_TIMER.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The msm_sdcc MMC driver and the msm_serial_hs uart driver both
use the pre-dmaengine interfaces provided by the MSM platform.
Since these drivers can be loadable modules, we should export
the functions used in the drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
MSM7X00A has an open-coded version of debug_ll_io_init so it
can use MT_DEVICE_NONSHARED as required by the platform.
However, this fails to build on no-MMU kernels because the
debug_ll_addr function is not available. Since the iotable_init
function doesn't actually do anyting in this configuration,
we can simply get away by enclosing the broken function call
in an #ifdef, which seems to be the least ugly workaround.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
After the restructuring of the module.h and init.h headers,
we now need to include this explicitly here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
This symbol is used by the lpc_eth driver, which may
be a loadable module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Roland Stigge <stigge@antcom.de>
The 'og' machine tries to always initialized the PCI code, but that
may be disabled in Kconfig, leading to a build error.
This patch changes the code to use the same Kconfig symbol to decide
about calling the ks8695_init_pci function at build time that we
use to decide about building the ks8695 PCI support.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Commit 098e30f655 "ARM: ixp4xx: stop broadcasting the custom GPIO API"
changed the internal gpio code of ixp4xx to be accessible only from
common.c, but unfortunately that broke the Goramo MultiLink code, which
uses this API.
This tries to restore the previous state without exposing the
API globally again. A better solution might be needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Imre Kaloz <kaloz@openwrt.org>
