and rename it to ath9k_cmn_setup_ht_cap
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename it to ath9k_cmn_init_channels_rates.
sbands are move to ath_common as well.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only set sc->rx.discard_next to rx_stats->rs_more when actually
discarding the current descriptor.
Also, fix a detection of broken descriptors:
First the code checks if the current descriptor is not done.
Then it checks if the next descriptor is done.
Add a check that afterwards checks the first descriptor again, because
it might have been completed in the mean time.
This fixes a regression introduced in
commit 723e711356
"ath9k: fix handling of broken descriptors"
Cc: stable@vger.kernel.org
Reported-by: Marco André Dinis <marcoandredinis@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check if the baseband state remains stable, and add a small delay
between register reads.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some chips, baseband watchdog hangs are more common than others, and
the driver has support for handling them.
Interrupts even after a watchdog hang are also quite common, so there's
not much point in spamming the user's logfiles.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
5/10 MHz channel bandwidth is configured via the PLL clock, instead of
the AR_PHY_MODE register. Using that register is AR93xx specific, and
makes the mode incompatible with earlier chipsets.
In some early versions, these flags were apparently applied at the wrong
point in time and thus did not cause connectivity issues, however now
they are causing problems, as pointed out in this OpenWrt ticket:
https://dev.openwrt.org/ticket/14916
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trivially reduces text size too.
$ size drivers/net/wireless/ath/ath9k/debug.o*
text data bss dec hex filename
34436 2528 5128 42092 a46c drivers/net/wireless/ath/ath9k/debug.o.new
34464 2528 5128 42120 a488 drivers/net/wireless/ath/ath9k/debug.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Number of MAC hangs and stuck beacons were missing
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 handles the actual operations, so ath9k can just indicate
support for this. Based on initial tests, this combination seems to
work fine.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When passing tx frames to the U-APSD queue for powersave poll responses,
the ath_atx_tid pointer needs to be passed to ath_tx_setup_buffer for
proper sequence number accounting.
This fixes high latency and connection stability issues with ath9k
running as AP and a few kinds of mobile phones as client, when PS-Poll
is heavily used
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The minimum CCA power threshold values have to be adjusted
for existing cards to be in compliance with new regulations.
Newer cards will make use of the values obtained from EEPROM,
support for this was added earlier. To make sure that cards
that are already in use and don't have proper values in EEPROM,
do not violate regulations, use the initvals instead.
Cc: stable@vger.kernel.org
Reported-by: Jeang Daniel <dyjeong@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a routine to calculate the median IQ correction
values for AR955x, which is used for outlier detection.
The normal method which is used for all other chips is
bypassed for AR955x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be used for storing data for mutiple
IQ calibration runs, for AR955x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IQ calibration post-processing for AR955x is different
from other chips - instead of just doing it as part
of AGC calibration once, it is triggered 3 times and
a median is determined. This patch adds initial support
for changing the calibration behavior for AR955x.
Also, to simplify things, a helper routine to issue/poll
AGC calibration is used.
For non-AR955x chips, the iqcal_idx (which will be used
in subsequent patches) is set to zero.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect values are programmed in the registers
containing the IQ correction coefficients by the IQ-CAL
post-processing code. Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ar9003_hw_tx_iq_cal_outlier_detection instead.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In chips like AR955x, the initvals contain the information
whether IQ calibration is to be done in the HW when an
AGC calibration is triggered. Check if IQ-CAL is enabled
in the initvals before flagging 'txiqcal_done' as true.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calibration data is not reused for SoC chips, so
call ar9003_hw_tx_iq_cal_post_proc() with the correct
argument. The 'is_reusable' flag is currently used
only for PC-OEM chips, but it makes things clearer to
specify it explicity.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Buffalo WLI-UV-AG300P is almost the same as Sony UWA-BR100.
Signed-off-by: Masaki TAGAWA <masaki@club.kyutech.ac.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no benefit in retaining the legacy rate control module
in the driver codebase.
It is known to be buggy and has less than optimal performance
in real-world environments compared with minstrel. The only
reason that it was kept when we made the switch to minstrel
as default was that it showed higher throughput numbers in a
clean/ideal environment.
This is no longer the case and minstrel can push ath9k to
the same throughput levels. In TCP, with 3-stream cards, more than
295 Mbps can be obtained in open air, with 2-stream cards,
210 Mbps is easily reached. To test performance issues,
instead of using a broken rate control module, it is better
to use the fixed-rate interface provided by mac80211 anyway.
The ath9k RC has not received any bug fixes in years and is
just bit-rotting away - this patch removes it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
after switch to common fucntions we do not need this memcpy any more.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and rename it to ath9k_cmn_rx_skb_postprocess. We will use it
on ath9k_htc.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we can reuse this function in ath9k_htc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we can reuse this fucntion on ath9k_htc.
Now we will need to use common version last_rssi, so switch
it too.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/main.c: In function ‘ath9k_has_tx_pending’:
drivers/net/wireless/ath/ath9k/main.c:1869: warning: ‘npend’ may be used uninitialized in this function
Introduced by commit 10e2318103 ("ath9k:
optimize ath9k_flush").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Fix IQ calibration" added a check
to ensure that valid i2_p_q2_a0_d1 values are not discarded.
But since it is masked with 0xfff earlier, the codepath
will not be executed.
The earlier case where all values above 0x800 were considered
invalid is incorrect, since the HW can return valid values
between 0x800 and 0xfff.
Cc: Kai Shi <kaishi@qca.qualcomm.com>
Reported-by: Alex Hacker <hacker@epn.ru>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Soon mac80211 will support multi-interface CSA so
using sc->csa_vif is not an option.
Instead just depend on vif->csa_active. Calling
ieee80211_csa_finish() multiple number of times
should not be an issue.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's not a single rate control algorithm actually in
a separate module where the module refcount would be
required. Similarly, there's no specific rate control
module.
Therefore, all the module handling code in rate control
is really just dead code, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the code to allow making all the rate control ops
const, nothing ever needs to change them. Also change all
drivers to make use of this and mark the ops const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The commit, "ath9k_hw: Fix incorrect Tx control power in AR9003 template"
fixed the incorrect values in the eeprom templates, but if
boards have already been calibrated with incorrect values,
they would still be using the wrong TX power. Fix this by assigning
a default value in such cases.
Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even though we make sure PowerSave is not enabled by default
by disabling the flag, WIPHY_FLAG_PS_ON_BY_DEFAULT on init,
PS could be enabled by userspace based on various factors
like battery usage etc. Since PS in ath9k is just broken
and has been untested for years, remove support for it, but
allow a user to explicitly enable it using a module parameter.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 ->sta_rc_update() callback must be atomic. Since we have to
take mutex and do other operations that can sleep when sending fimrware
commands to device, the only option to satisfy atomicity requirement of
->sta_rc_update(), that I can see, is introduce work_struct and defer
uploading new rates to that work.
Tested-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is a copy/paste of patch provided by Sujith for ath9k.
"Even though we make sure PowerSave is not enabled by default
by disabling the flag, WIPHY_FLAG_PS_ON_BY_DEFAULT on init,
PS could be enabled by userspace based on various factors
like battery usage etc. Since PS in ath9k is just broken
and has been untested for years, remove support for it, but
allow a user to explicitly enable it using a module parameter."
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sta_rc_update() callback must be atomic, hence we can not take mutexes
or do other operations, which can sleep in ath9k_htc_sta_rc_update().
I think we can just return from ath9k_htc_sta_rc_update(), if it is
called without IEEE80211_RC_SUPP_RATES_CHANGED bit. That will help
with scheduling while atomic bug for most cases (except mesh and IBSS
modes).
For mesh and IBSS I do not see other solution like creating additional
workqueue, because sending firmware command require us to sleep, but
this can be done in additional patch.
Patch partially fixes bug:
https://bugzilla.redhat.com/show_bug.cgi?id=990955
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The threshold values for RX interrupt mitigation
are different for AR9003 and AR9002 families.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Process GTT interrupts" accidentally
had a line that was commented out.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will also change behavior of rx_beacons statistic.
Instead of collecting all received beacons, it will collect only
ours. This, IMO make more sense, since for troubleshooting we will
need to know count of our beacons, or both.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
