The small delay that is present between a RTC reset/clear
operation is required for the chip to settle and this is
needed for all chips, not just the AR9002 family.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To comply with ETSI regulations, make sure that
the CCA registers are programmed with the threshold
values from the EEPROM/Caldata. A new field is used
to indicate if the card has been calibrated with the
required threshold information.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add a new field "misc_enable"
* Use int_8 for tempslopextension.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt reference counter is always initialized
in ath9k_start().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Move definitions to spectral.h
* Move processing/debug code to spectral.c
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon code previously reset TSF on every configuration call, as
some of the code was not prepared to properly calculate nexttbtt based
on current TSF.
This patch adds a common function for calculating nexttbtt and moves the
TSF reset to driver start.
This should improve AP mode compatibility with various stations that
expect the TSF to not randomly jump due to hardware resets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused fields, pass timer info in usec instead of TU.
Preparation for fixing nexttbtt calculation
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ah->config.spurmode and ah->config.spurchans, always use EEPROM
data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware does not have support for ATIM processing, and the driver
does not set up ah->atim_window anywhere. Additionally, the code can
clobber the timer used by P2P powersave.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Use generic bitops instead of custom hackery
- Move interrupt enable/disable logic from ath9k to ath9k_hw
- Decouple ISR call from btcoex
- Make the overflow callback optional (to prevent IRQ storms)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TSF accuracy is not needed here, and there is only one usable generic
timer that is supported by all chips and uses the primary TSF counter.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to truncate curchan->hw_value to u8
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move ath9k_hw_set_rfmode() after ath9k_hw_process_ini() in order to avoid
AR_PHY_MODE register is overwritten with default values by
ar9003_hw_process_ini()
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On suspend/resume, firmware will restart and gpios
configuration will be reseted. Restore this
configureation at least for LEDs
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a driver workaround for a HW issue.
A race condition in the HW results in missing interrupts,
which can be avoided by a read/write with the ISR register.
All chips in the AR9002 series are affected by this bug - AR9003
and above do not have this problem.
Cc: stable@vger.kernel.org
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pick the MAC address of the first virtual interface as the new hardware MAC
address. Set BSSID mask according to this MAC address. This fixes CVE-2013-4579.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize first chain flags in ath9k_build_tx99_skb() according to
configured channel mode and channel width
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The internal regulator needs to be programmed
correctly for AR955x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjusting the CCA registers for maximum permissible
noise floor in ETSI/Japan domains has to be done for
all AR9003 family chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the Buffalo-specific initvals have been
moved to a separate array, update the default high
power TX gain table for all AR9300 v2.2 devices.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Buffalo device WZR-HP-G450H uses the index 3 for TX gain,
which is set to the high_power table currently. Later variants
of the router use the same index, but instead refer to the
low_ob_db gain table. This is not handled in the driver since
there is no way to distinguish board revisions and the high_power
table is used (incorrectly) for the newer variants.
By default, devices based on AR9300 using the TX gain index 3 have
to use the high_power table. To make sure that WZR-HP-G450H is not
broken when the high_power table is updated, use a separate array
based on information obtained from the platform data.
The current situation where only the original variant of WZR-HP-G450H
works properly stays unchanged.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update radio/baseband/gain tables.
* Mark ar9331_modes_high_power_tx_gain_1p1 as a duplicate
* ar9331_1p1_mac_postamble is not a duplicate.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable the ALWAYS_KEYSEARCH bit in the initvals. Currently
this is done in the driver, but adding this to the initvals
makes it easier to be in sync with the INI files given
by the systems engineering team.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Certain baseband registers require different values
to be programmed when operating in a DFS channel to
ensure that radar detection works correctly. This
is required for AR9300, AR9340 and AR9580.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When not aggregating packets, fi->framelen should be passed in as length
to calculate the duration. Before the tx path rework, ath_tx_fill_desc
was called for either one aggregate, or one single frame, with the
length of the packet or the aggregate as a parameter.
After the rework, ath_tx_sched_aggr can pass a burst of single frames to
ath_tx_fill_desc and sets len=0.
Fix broken duration calculation by overriding the length in ath_tx_fill_desc
before passing it to ath_buf_set_rate.
Cc: stable@vger.kernel.org
Reported-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize first chain attempt counter to 1 in ath9k_build_tx99_skb().
Otherwise multi-retry chain is initialized to {idx,count} = {-1, 0} in
rate_control_fill_sta_table() and tx99 transmission rate is not configured in
rate_control_apply_mask() since first chain idx is set to -1
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is missing for AR9300, AR9580 and AR9340.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Baseband updates
* Remove ar9340Common_rx_gain_table_1p0 since it is a duplicate.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initvals for AR9462 v2.1 are very similar to v2.0.
Identify duplicate arrays and reuse the values from v2.0
to reduce module size.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
