Ensure we call unmap_mapping_range() and sync dirty pages to disk before
doing an NFS direct write.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When we insert a new xfrm_state which potentially
subsumes an existing one, make sure all cached
bundles are flushed so that the new SA is used
immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
I reported a problem and gave hints to the solution, but nobody seemed
to react. So I prepared a patch against 2.6.14.4.
Tested on 2.6.14.4 with "ip monitor addr" and with the program
attached, while adding and removing IPv6 address. Both programs didn't
receive any messages. Tested 2.6.14.4 + this patch, and both programs
received add and remove messages.
Signed-off-by: Kristian Slavov <kristian.slavov@nomadiclab.com>
Acked-by: Jamal Hadi salim <hadi@cyberus.ca>
ACKed-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This (and the three subsequent patches) is working well on OMAP H4 with
2.6.15-rc4 kernel and passes the LTP fs test.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
DMA_MODE_{READ,WRITE} are declared in asm-powerpc/dma.h and their
declarations there match the definitions. Old declarations in
ppc4xx_dma.h are not right anymore (wrong type, to start with).
Killed them, added include of asm/dma.h where needed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sparc64, i386 and x86_64 have support for a special data section dedicated
to rarely updated data that is frequently read. The section was created to
avoid false sharing of those rarely read data with frequently written kernel
data.
This patch creates such a data section for ia64 and will group rarely written
data into this section.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The logic that decides that a fork() might be able to avoid copying a VM
area when it can be re-created by page faults didn't know about the new
vm_insert_page() case.
Also make some things a bit more anal wrt VM_PFNMAP.
Pointed out by Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The udelay() inline for ia64 uses the ITC. If CONFIG_PREEMPT is enabled
and the platform has unsynchronized ITCs and the calling task migrates
to another CPU while doing the udelay loop, then the effective delay may
be too short or very, very long.
This patch disables preemption around 100 usec chunks of the overall
desired udelay time. This minimizes preemption-holdoffs.
udelay() is now too big to be inline, move it out of line and export it.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
In the scenario that a link was broken, the devloss timer for each
rport was expire at roughly the same time, causing lots of "delete"
workqueue items being queued. Depth is dependent upon the number of
rports that were on the link.
The rport target remove calls were calling flush_scheduled_work(),
which would interrupt the stream, and start the next workqueue item,
which did the same thing, and so on until recursion depth was large.
This fix stops the recursion in the initial delete path, and pushes it
off to a host-level work item that reaps the dead rports.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rename scsi_print_msg to spi_print_msg and move its prototype from
scsi_dbg.h to scsi_transport_spi.h
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This merge is pretty extensive. The conflict is over the new
req->retries parameter, so I had to change the prototype to
scsi_setup_blk_pc_cmnd() and the usage in sd, sr and st.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- export __blk_put_request and blk_execute_rq_nowait
needed for async REQ_BLOCK_PC requests
- seperate max_hw_sectors and max_sectors for block/scsi_ioctl.c and
SG_IO bio.c helpers per Jens's last comments. Since block/scsi_ioctl.c SG_IO was
already testing against max_sectors and SCSI-ml was setting max_sectors and
max_hw_sectors to the same value this does not change any scsi SG_IO behavior. It only
prepares ll_rw_blk.c, scsi_ioctl.c and bio.c for when SCSI-ml begins to set
a valid max_hw_sectors for all LLDs. Today if a LLD does not set it
SCSI-ml sets it to a safe default and some LLDs set it to a artificial low
value to overcome memory and feedback issues.
Note: Since we now cap max_sectors to BLK_DEF_MAX_SECTORS, which is 1024,
drivers that used to call blk_queue_max_sectors with a large value of
max_sectors will now see the fs requests capped to BLK_DEF_MAX_SECTORS.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
http://bugzilla.kernel.org/show_bug.cgi?id=4320
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
For tape we need to control the retries. This patch adds a retries
counter on the request for REQ_BLOCK_PC commands originating from
scsi_execute* to use. REQ_BLOCK_PC commands comming from the block
layer SG_IO path continue to use the retires set in the ULD init_command.
(scsi_execute* does not set the gendisk so we do not execute
the init_command in that path).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add scsi helpers to create really-large-requests and convert
scsi-ml to scsi_execute_async().
Per Jens's previous comments, I placed this function in scsi_lib.c.
I made it follow all the queue's limits - I think I did at least :), so
I removed the warning on the function header.
I think the scsi_execute_* functions should eventually take a request_queue
and be placed some place where the dm-multipath hw_handler can use them
if that failover code is going to stay in the kernel. That conversion
patch will be sent in another mail though.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
To send async requests we need these two functions exported.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes here include removing all of CONFIG_PM while it is being repeatedly
smacked with a lead pipe, moving the BURSTMODE param to a #define (it should
be defined almost always anyway), fixing the rqsize stuff, pulling ide_ioreg_t,
and general cleanups and whatnot.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some motherboards (such as the Asus P5V800-MX) ship a
PCI_DEVICE_ID_VIA_82C586_1 IDE controller alongside a VT8251 southbridge.
This southbridge is currently unrecognised in the via82cxxx IDE driver,
preventing those users from getting DMA access to disks.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Patch from Daniel Jacobowitz
Handle new EABI relocations when loading kernel modules. This is
necessary for CONFIG_AEABI kernels, and also for some broken
(since fixed) old ABI toolchains.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This follows on from Jens' patch and consolidates all of the ULD
separate handlers for REQ_BLOCK_PC into a single call which has his
fix for our direction bug.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add forward declarations to allow scsi_transport_spi.h to be compiled by
itself.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make the vendor, model and rev fields in scsi_device pointers to const
and update a few prototypes of functions using them.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ERR_SEVERITY item is defined as a 8 bits item in SAL documentation
($B.2.1 rev december 2003), but as an u16 in sal.h.
This has the side effect that current code in mca.c may not call
ia64_sal_clear_state_info() upon receiving corrected platform errors
if there are bits set in the validation byte. Reported by Xavier Bru.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Some hardware does not support the PACKET command at all.
Other hardware supports ATAPI, but the driver does something nasty such
as calling BUG() when an ATAPI command is issued.
For these such cases, we mark them with a new flag, ATA_FLAG_NO_ATAPI.
Initial version contributed by Ben Collins.
There is no user of qc->waiting left after ata_exec_internal()
changes. Kill the field.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch implements ata_exec_internal() function which performs
libata internal command execution. Previously, this was done by each
user by manually initializing a qc, issueing it, waiting for its
completion and handling errors. In addition to obvious code
factoring, using ata_exec_internal() fixes the following bugs.
* qc not freed on issue failure
* ap->qactive clearing could race with the next internal command
* race between timeout handling and irq
* ignoring error condition not represented in tf->status
Also, qc & hardware are not accessed anymore once it's completed,
making internal commands more conformant with general semantics.
ata_exec_internal() also makes it easy to issue internal commands from
multiple threads if that becomes necessary.
This patch only implements ata_exec_internal(). A following patch
will convert all users.
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
Jeff, all patches have been regenerated against upstream branch as of
today. (575ab52a21)
Also, I took out a debug printk from ata_exec_internal (don't know how
that one got left there). Other than that, all patches are identical
to the previous posting.
Thanks. :-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The drawing function cfbfillrect does not work correctly when access is not
unsigned-long aligned. It manifests as extra lines of pixels that are not
complete drawn. Reversing the shift operator solves the problem, so I would
presume that this bug would manifest only on little endian machines. The
function cfbcopyarea may also have this bug.
Aligned access should present no problems.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Every framebuffer driver relies on the assumption that the set_par()
function of the driver is called before drawing functions and other
functions dependent on the hardware state are executed.
Whenever you switch from X to a framebuffer console for the very first
time, there is a chance that a broken X system has _not_ set the mode to
KD_GRAPHICS, thus the vt and framebuffer code executes a screen redraw and
several other functions before a set_par() is executed. This is believed
to be not a bug of linux but a bug of X/xdm. At least some X releases used
by SuSE and Debian show this behaviour.
There was a 2nd case, but that has been fixed by Antonino Daplas on
10-dec-2005.
This patch allows drivers to set a flag to inform fbcon_switch() that they
prefer a set_par() call on every console switch, working around the
problems caused by the broken X releases.
The flag will be used by the next release of cyblafb and might help other
drivers that assume a hardware state different to the one used by X.
As the default behaviour does not change, this patch should be acceptable
to everybody.
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Acked-by: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add hooks to save and restore the graphics state. These hooks are called in
fbcon_blank() when entering/leaving KD_GRAPHICS mode. This is needed by
savagefb at least so it can cooperate with savage_dri and by cyblafb.
State save/restoration can be full or partial.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
