We should count also dropped packets, otherwise the NAPI handler may
end up running too long.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: devel@driverdev.osuosl.org
Cc: linux-mips@linux-mips.org
Cc: David Daney <david.daney@cavium.com>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: richard@nod.at
Patchwork: https://patchwork.linux-mips.org/patch/5809/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Double wide mode is only available on pipe A, except on GDG where
pipe B is also double wide capable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pipe horizontal source size must be even when either LVDS dual channel
mode, DVO ganged mode, or pipe double wide mode is used.
We must round it down since we can never increase the user specified
viewport size.
The actual error from an odd pipe source width looks like a diagonal
shift, like you might get from a bad stride.
v2: s/ganaged/ganged/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't want to try to push the hardware beyond it's capabilities,
so check the pixel clock against the display core clock limit. Do
it for pre-gen4 for now since that's where we alread have the double
wide pixel clock limit check.
Let's assume that when double wide mode is enabled the max
pixel clock limit is also doubled.
FIXME: panel fitter downscaling probably affects the limit on
non-pch platforms too, so we'd need another version of
ilk_pipe_pixel_rate() to figure that out.
FIXME: should check the limits on all platforms. Also sprites
affect the max allowed pixel rate on some platforms, so we need
to eventually tie all the planes and pipes into one check in
the future. But we need plane state pre-compute before that can
happen.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read the double wide pipe information from hardware in
i9xx_get_pipe_config(), and check it in intel_pipe_config_compare()
For gen4+ double_wide is always false so the comparison can be done
on all platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Determine the need for double wide mode already in compute_config
stage as we need that information to figure out if horizontal
coordinates need to be adjusted.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simply inline the 100MHz default we're using. Having gunk around that
has leftover LVDS support on a platform that just doesn't have this
isn't of any use.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First of all we should not be looking at fb->{width,height} as those do
not tell us what the actual pipe size is. Second of all we need to use
>= for the comparison.
So fix the comparison, and make use of the new pipe_src_{w,h} to
determine the real pipe source dimensions.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the cursor x coordinate is exactly -cursor_width, the cursor is
invisible. And obviously the same holds for the y coordinate and
cursor_height.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to clarify the purpose of requested_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Especially intel_gmch_panel_fitting was shifting way too much over the
right edge and also was way too long. So extract two helpers, one for
gen4+ and one for gen2/3. Now the entire thing is again almost
readable ...
Spurred by checkpatch freaking out about a Ville's pipeconfig rework
in intel_panel.c
Otherwise just two lines that needed appropriate breaking.
Not functional change in this patch.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
the wake_up_process func is included by spin_lock/unlock in
vhost_work_queue,
but it could be done outside the spin_lock.
I have test it with kernel 3.0.27 and guest suse11-sp2 using iperf,
the num as below.
original modified
thread_num tp(Gbps) vhost(%) | tp(Gbps) vhost(%)
1 9.59 28.82 | 9.59 27.49
8 9.61 32.92 | 9.62 26.77
64 9.58 46.48 | 9.55 38.99
256 9.6 63.7 | 9.6 52.59
Signed-off-by: Chuanyu Qin <qinchuanyu@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The patch "0b7a76a ARM: dts: imx6q{dl}: add DTE pads for uart"
adds the DTE pads for uart. For PAD_EIM_D29, the offset of the
Pad Mux register should be 0x0c8, not 0x0c4.
This patch fixes it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0
The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2
But according to ARM PL310 errata: 752271
ID: 752271: Double linefill feature can cause data corruption
Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2
Workaround: The only workaround to this erratum is to disable the
double linefill feature. This is the default behavior.
without this patch, you will meet the following error when run the
memtester application at: http://pyropus.ca/software/memtester/
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365664.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365668.
FAILURE: 0x00100000 != 0x00200000 at offset 0x0136566c.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365670.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365674.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365678.
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Commit 718a350 (ARM: i.MX51: Add PATA support) adds pata support to the
imx51.dtsi file and is using clock 161. The problem is that the right
clock is 172, according to commit 5d530bb (ARM: i.MX5: Add PATA and SRTC
clocks). Using the clock 172 makes things work again (and kills a nasty
system freeze).
Tested-by: Steev Klimaszewski <steev@gentoo.org>
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit beb2d1c1ba (ARM i.MX5: Add S/PDIF clocks), the following clock
error appears on mx51:
TrustZone Interrupt Controller (TZIC) initialized
i.MX51 clk 180: register failed with -17
i.MX5 clk 180: register failed with -17
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
CPU identified as i.MX51, silicon rev 3.0
...
Clock 180 corresponds to 'spdif1_podf' and this clock is getting registered
twice.
Fix it, by properly registering the 'spdif1_pred' clock, which should not
reference 'spdif1_podf'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The clk_init_data.flags of clk-fixup-mux is left there without
initialization. It may hold some random data and cause clock framework
interpret the clock in an unexpected way. At least on imx6sl, the
following division by zero error with sched_clock is seen because of it.
Division by zero in kernel.
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.11.0-rc3+ #19
Backtrace:
[<80011af0>] (dump_backtrace+0x0/0x10c) from [<80011c90>] (show_stack+0x18/0x1c)
r6:3b9aca00 r5:00000020 r4:00000000 r3:00000000
[<80011c78>] (show_stack+0x0/0x1c) from [<8055e02c>] (dump_stack+0x78/0x94)
[<8055dfb4>] (dump_stack+0x0/0x94) from [<80011924>] (__div0+0x18/0x20)
r4:00000000 r3:00000000
[<8001190c>] (__div0+0x0/0x20) from [<8026c408>] (Ldiv0_64+0x8/0x18)
[<8006330c>] (clocks_calc_mult_shift+0x0/0xf8) from [<8072f604>] (setup_sched_clock+0x88/0x1f0)
[<8072f57c>] (setup_sched_clock+0x0/0x1f0) from [<8071ad48>] (mxc_timer_init+0xe8/0x17c)
[<8071ac60>] (mxc_timer_init+0x0/0x17c) from [<807290b0>] (imx6sl_clocks_init+0x1db8/0x1dc0)
r8:807a9ca4 r7:00000000 r6:80777564 r5:8100c1f4 r4:c0820000
[<807272f8>] (imx6sl_clocks_init+0x0/0x1dc0) from [<807420ac>] (of_clk_init+0x40/0x6c)
[<8074206c>] (of_clk_init+0x0/0x6c) from [<807290cc>] (imx6sl_timer_init+0x14/0x18)
r5:807a8e80 r4:ffffffff
[<807290b8>] (imx6sl_timer_init+0x0/0x18) from [<80716e1c>] (time_init+0x24/0x34)
[<80716df8>] (time_init+0x0/0x34) from [<80713738>] (start_kernel+0x1b0/0x310)
[<80713588>] (start_kernel+0x0/0x310) from [<80008074>] (0x80008074)
r7:80770b08 r6:80754cd4 r5:8076c8c4 r4:10c53c7d
sched_clock: 32 bits at 0 Hz, resolution 0ns, wraps every 0ms
Fix the bug by initializing init.flags as zero.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Ben Hutchings says:
====================
Some bug fixes and future-proofing for the recently added SFC9120
support:
1. Minimal support for the 40G configuration.
2. Disable the incomplete PTP/hardware timestamping support.
3. Reset MAC stats properly after a firmware upgrade.
4. Re-check the datapath firmware capabilities after the controller is
reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt the same behaviour for SCTP as present in TCP for ICMP redirect
messages. For IPv6, RFC4443, section 2.4. says:
...
(e) An ICMPv6 error message MUST NOT be originated as a result of
receiving the following:
...
(e.2) An ICMPv6 redirect message [IPv6-DISC].
...
Therefore, do not report an error to user space, just invoke dst's redirect
callback and leave, same for IPv4 as done in TCP as well. The implication
w/o having this patch could be that the reception of such packets would
generate a poll notification and in worst case it could even tear down the
whole connection. Therefore, stop updating sk_err on redirects.
Reported-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use USB_DEVICE_AND_INTERFACE_INFO and USB_VENDOR_AND_INTERFACE_INFO
macros to reduce boilerplate.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: <stable@vger.kernel.org> # 3.0+ as far back as it applies cleanly
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_IPTUN_LOCAL and IFLA_IPTUN_REMOTE were inverted.
Introduced by c075b13098 (ip6tnl: advertise tunnel param via rtnl).
Signed-off-by: Ding Zhi <zhi.ding@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch it is impossible to read et_swtype, because the 1
byte space is needed for the terminating null byte. The max expected
value is 0xF, so now it should be possible to read decimal form ("15")
and hex form ("0xF").
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.
Use correct bit for switch initialization and fix typo in the define.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Use separate table for alias entries in the ehea module, otherwise the
probe() function will operate on the separate ports instead of the
lhea-"root" entry of the device-tree
Addresses https://bugzilla.novell.com/show_bug.cgi?id=435215
[ Thadeu notes that: "... this issue might happen with the generation of
initrd, when the scripts check for /sys/class/net/eth0/device/modalias,
which links to the port device at
/sys/devices/ibmebus/23c00400.lhea/port0/" ]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Olaf Hering <ohering@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If O_CREAT|O_EXCL are passed to open, then we know that either
- the file is successfully created, or
- the operation fails in some way.
So previously we set FILE_CREATED before calling ->atomic_open() so the
filesystem doesn't have to. This, however, led to bugs in the
implementation that went unnoticed when the filesystem didn't check for
existence, yet returned success. To prevent this kind of bug, require
filesystems to always explicitly set FILE_CREATED on O_CREAT|O_EXCL and
verify this in the VFS.
Also added a couple more verifications for the result of atomic_open():
- Warn if filesystem set FILE_CREATED despite the lack of O_CREAT.
- Warn if filesystem set FILE_CREATED but gave a negative dentry.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Set FILE_CREATED on O_CREAT|O_EXCL. If the NFS server honored our request
for exclusivity then this must be correct.
Currently this is a no-op, since the VFS sets FILE_CREATED anyway. The
next patch will, however, require this flag to be always set by
filesystems.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In gfs2_create_inode() set FILE_CREATED in *opened.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If an error occurs after having called finish_open() then fput() needs to
be called on the already opened file.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Steve French <sfrench@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix documentation of ->atomic_open() and related functions: finish_open()
and finish_no_open(). Also add details that seem to be unclear and a
source of bugs (some of which are fixed in the following series).
Cc-ing maintainers of all filesystems implementing ->atomic_open().
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Steve French <sfrench@samba.org>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Don't drop ->wq_mutex before calling autofs4_notify_daemon() only to regain it
there. Besides being pointless, that opens a race window where autofs4_wait_release()
could've come and freed wq->name.name. And do the debugging printk in the "reused an
existing wq" case before dropping ->wq_mutex - the same reason...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Ian Kent <raven@themaw.net>
Rather that mess about with hdisplay/vdisplay from requested_mode, add
explicit pipe src size information to pipe config.
Now requested_mode is only really relevant for dvo/sdvo output timings.
For everything else either adjusted_mode or pipe src size should be
used.
In many places where we end up using pipe source size, we should
actually use the primary plane size, but we don't currently store
that information explicitly. As long as we treat primaries as full
screen only, we can get away with this. Eventually when we move
primaries over to drm_plane, we need to fix it all up.
v2: Add a comment to explain what pipe_src_{w,h} are
Add a note about primary planes to commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
adjusted_mode contains our real timings, not requested_mode. Use the
correct thing in DSI PLL code.
Also constify adjusted_mode since we don't change it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than dig up the pipe source size from crtc->mode, use
intel_crtc->config.requested_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move intel_crtc_active() to intel_display.c and make it available
elsewhere as well.
intel_edp_psr_match_conditions() already has one open coded copy,
so replace that one with a call to intel_crtc_active().
v2: Copy paste a big comment from danvet's mail explaining
when we can ditch the extra checks
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_edp_psr_match_conditions() currently looks at crtc->mode
when it really needs to look at adjusted_mode. Fix it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The clock in crtc->mode doesn't necessarily mean anything. Let's look
at the clock in adjusted_mode instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently most of the watermark code looks at crtc->mode which is the
user requested mode. The only piece of information there that is
relevant is hdisplay, the rest must come from adjusted_mode. Convert
all of the code to use requested_mode and adjusted_mode from
pipe config appropriately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check the mode flags from the adjusted_mode, not user requested mode.
The hdisplay/vdisplay check actually checkes the primary plane size,
so those still need to come from the user requested mode.
Extract both modes from pipe config instead of the drm_crtc.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pixel clock should come from adjusted_mode not requested_mode.
In this case the two should be the same as we don't currently
overwrite the clock in the case of HDMI. But let's make the code
safe against such things happening in the future.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
lpt_program_iclkip() wants to know the pixel clock. It should get that
information from adjusted_mode, not crtc->mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i9xx_set_pipeconf() attempts to get the current pixel clock from
requested_mode. requested_mode.clock may be totally bogus, so the
clock should come from adjusted_mode.
v2: Dropped the intel_compute_config() hunk due to killing of the
INTEL_FDI_FREQ check
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check and dump for port_clock.
v2: Also dump port_clock
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new pipe config check macro PIPE_CONF_CHECK_CLOCK_FUZZY() to make
it trivial and error proof to compare clocks in a fuzzy manner.
v2: Drop extra curly braces
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that adjusted_mode.clock no longer contains the pixel_multiplier, we
can kill the get_clock() callback and instead do the clock readout
in get_pipe_config().
Also i9xx_crtc_clock_get() can now extract the frequency of the PCH
DPLL, so use it to populate port_clock accurately for PCH encoders.
For DP in port A the encoder is still responsible for filling in
port_clock. The FDI adjusted_mode.clock extraction is kept in place
for some extra sanity checking, but we no longer need to pretend it's
also the port_clock.
In the encoder get_config() functions fill out adjusted_mode.clock
based on port_clock and other details such as the DP M/N values,
HDMI 12bpc and SDVO pixel_multiplier. For PCH encoders we will then
do an extra sanity check to make sure the dotclock we derived from
the FDI configuratiuon matches the one we derive from port_clock.
DVO doesn't exist on PCH platforms, so it doesn't need to anything
but assign adjusted_mode.clock=port_clock. And DDI is HSW only, so
none of the changes apply there.
v2: Use hdmi_reg color format to detect 12bpc HDMI case
v3: Set adjusted_mode.clock for LVDS too
v4: Rename ironlake_crtc_clock_get to ironlake_pch_clock_get,
eliminate the useless link_freq variable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add the 120MHz refernce clock case for PCH DPLLs.
Also determine the reference clock frequency more accurately by
checking for the PLLB_REF_INPUT_SPREADSPECTRUMIN refclk input
mode. The gen2 code already checked it, but it stil assumed a
fixed 66MHz refclk. Instead we need to consult the VBT for the
real value.
v2: Fix refclk for SSC panel case
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
