git-annex/doc/design/git-remote-daemon.mdwn

# goals

* be configured like a regular git remote, with an unusual url
  or other configuration
* receive notifications when a remote has received new commits,
  and take some action
* optionally, do receive-pack and send-pack to a remote that
  is only accessible over an arbitrary network transport
  (like assistant does with XMPP)
* optionally, send/receive git-annex objects to remote
  over an arbitrary network transport

# difficulties

* authentication & configuration
* multiple nodes may be accessible over a single network transport,
  with it desirable to sync with any/all of them. For example, with
  XMPP, there can be multiple friends synced with. This means that
  one git remote can map to multiple remote nodes. Specific to git-annex,
  this means that a set of UUIDs known to be associated with the remote
  needs to be maintained, while currently each remote can only have one
  annex-uuid in .git/config.

# payoffs

* support [[assistant/telehash]]!
* Allow running against a normal ssh git remote. This would run
  git-annex-shell on the remote, watching for changes, and so be able to
  notify when a commit was pushed to the remote repo. This would let the
  assistant immediately notice and pull. So the assistant would be fully
  usable with a single ssh remote and no other configuration!
  **do this first**
* clean up existing XMPP support, make it not a special case, and not
  tightly tied to the assistant
* git-remote-daemon could be used independantly of git-annex,
  in any git repository.

# design

Let git-remote-daemon be the name. Or for git-annex,
`git annex remotedaemon`.

It runs in one of two ways:

1. Forked to background, using a named pipe for the control protocol.
2. With --foreground, the control protocol goes over stdio.

Either way, behavior is the same:

* Get a list of remotes to act on by looking at .git/config
* Automatically notices when a remote has changes to branches
  matching remote.$name.fetch, and pulls them down to the appropriate
  location.
* When the control protocol informs it about a new ref that's available,
  it offers the ref to any interested remotes.

# control protocol

This is an asynchronous protocol. Ie, either side can send any message
at any time, and the other side does not send a reply.

It is line based and intended to be low volume and not used for large data.

TODO: Expand with commands for sending/receiving git-annex objects, and
progress during transfer.

TODO: Will probably need to add something for whatever pairing is done by
the webapp.

## emitted messages

* `CONNECTED $remote`

  Sent when a connection has been made with a remote.

* `DISCONNECTED $remote`

  Sent when connection with a remote has been lost.

* `SYNCING $remote`

  Indicates that a pull or a push with a remote is in progress.
  Always followed by DONESYNCING.

* `DONESYNCING 1|0 $remote`

  Indicates that syncing with a remote is done, and either succeeded
  (1) or failed (0).

## consumed messages

* `PAUSE`

  This indicates that the network connection has gone down,
  or the user has requested a pause.
  git-remote-daemon should close connections and idle.

  Affects all remotes.

* `RESUME`

  This indicates that the network connection has come back up, or the user
  has asked it to run again. Start back up network connections.

  Affects all remotes.

* `CHANGED ref ...`

  Indicates that a ref is new or has changed. These can be offered to peers,
  and peers that are interested in them can pull the content.

* `RELOAD`

  Indicates that configs have changed. Daemon should reload .git/config
  and/or restart.

  Possible config changes include adding a new remote, removing a remote,
  or setting `remote.<name>.annex-sync` to configure whether to sync with a
  particular remote.

* `STOP`

  Shut down git-remote-daemon

  (When using stdio, it also should shutdown when it reaches EOF on 
  stdin.)

# encryption & authentication

For simplicity, the network transports have to do their own end-to-end
encryption. Encryption is not part of this design.

(XMPP does not do end-to-end encryption, but might be supported
transitionally.)

Ditto for authentication that we're talking to who we indend to talk to.
Any public key data etc used for authenticion is part of the remote's
configuration (or hidden away in a secure chmodded file, if neccesary).
This design does not concern itself with authenticating the remote node,
it just takes the auth token and uses it.

For example, in telehash, each node has its own keypair, which is used
or authentication and encryption, and is all that's needed to route
messages to that node.

# network level protocol

How do peers communicate with one another over the network?

This seems to need to be network-layer dependant. Telehash will need
one design, and git-annex-shell on a central ssh server has a very different
(and much simpler) design.

## ssh

`git-annex-shell notifychanges` is run, and speaks a simple protocol
over stdio to inform when refs on the remote have changed.

No pushing is done for CHANGED, since git handles ssh natively.

TODO:

* Remote system might not be available. Find a smart way to detect it,
  ideally w/o generating network traffic. One way might be to check
  if the ssh connection caching control socket exists, for example.
* Remote system might be available, and connection get lost. Should
  reconnect, but needs to avoid bad behavior (ie, constant reconnect
  attempts.)
* Detect if old system had a too old git-annex-shell and avoid bad behavior
* CONNECTED and DISCONNECTED are not wired into any webapp UI; could be
  used to show an icon when a ssh remote is available

## telehash 

TODO

## xmpp

Reuse [[assistant/xmpp]]