When quvi is installed, git-annex addurl automatically uses it to detect
when an page is a video, and downloads the video file.
web special remote: Also support using quvi, for getting files,
or checking if files exist in the web.
This commit was sponsored by Mark Hepburn. Thanks!
Started with a problem when running addurl on a really long url,
because the whole url is munged into the filename. Ended up doing
a fairly extensive review for places where filenames could get too large,
although it's hard to say I'm not missed any..
Backend.Url had a 128 character limit, which is fine when the limit is 255,
but not if it's a lot shorter on some systems. So check the pathconf()
limit. Note that this could result in fromUrl creating different keys
for the same url, if run on systems with different limits. I don't see
this is likely to cause any problems. That can already happen when using
addurl --fast, or if the content of an url changes.
Both Command.AddUrl and Backend.Url assumed that urls don't contain a
lot of multi-byte unicode, and would fail to truncate an url that did
properly.
A few places use a filename as the template to make a temp file.
While that's nice in that the temp file name can be easily related back to
the original filename, it could lead to `git annex add` failing to add a
filename that was at or close to the maximum length.
Note that in Command.Add.lockdown, the template is still derived from the
filename, just with enough space left to turn it into a temp file.
This is an important optimisation, because the assistant may lock down
a bunch of files all at once, and using the same template for all of them
would cause openTempFile to iterate through the same set of names,
looking for an unused temp file. I'm not very happy with the relatedTemplate
hack, but it avoids that slowdown.
Backend.WORM does not limit the filename stored in the key.
I have not tried to change that; so git annex add will fail on really long
filenames when using the WORM backend. It seems better to preserve the
invariant that a WORM key always contains the complete filename, since
the filename is the only unique material in the key, other than mtime and
size. Since nobody has complained about add failing (I think I saw it
once?) on WORM, probably it's ok, or nobody but me uses it.
There may be compatability problems if using git annex addurl --fast
or the WORM backend on a system with the 255 limit and then trying to use
that repo in a system with a smaller limit. I have not tried to deal with
those.
This commit was sponsored by Alexander Brem. Thanks!
Most remotes have meters in their implementations of retrieveKeyFile
already. Simply hooking these up to the transfer log makes that information
available. Easy peasy.
This is particularly valuable information for encrypted remotes, which
otherwise bypass the assistant's polling of temp files, and so don't have
good progress bars yet.
Still some work to do here (see progressbars.mdwn changes), but this
is entirely an improvement from the lack of progress bars for encrypted
downloads.
* addurl: Register transfer so the webapp can see it.
* addurl: Automatically retry downloads that fail, as long as some
additional content was downloaded.
In indirect mode, now checks the inode cache to detect changes to a file.
Note that a file can still be changed if a process has it open for write,
after landing in the annex.
In direct mode, some checking of the inode cache was done before, but
from a much later point, so fewer modifications could be detected. Now it's
as good as indirect mode.
On crippled filesystems, no lock down is done before starting to add a
file, so checking the inode cache is the only protection we have.
This avoids some small overhead by only running the check once per command;
it also ensures that, even if the command doesn't find anything to run on,
it still fails to run when in a bare repo.
Kqueue needs to remember which files failed to be added due to being open,
and retry them. This commit gets the data in place for such a retry thread.
Broke KeySource out into its own file, and added Eq and Ord instances
so it can be stored in a Set.
Now gitattributes are looked up, efficiently, in only the places that
really need them, using the same approach used for cat-file.
The old CheckAttr code seemed very fragile, in the way it streamed files
through git check-attr.
I actually found that cad8824852
was still deadlocking with ghc 7.4, at the end of adding a lot of files.
This should fix that problem, and avoid future ones.
The best part is that this removes withAttrFilesInGit and withNumCopies,
which were complicated Seek methods, as well as simplfying the types
for several other Seek methods that had a Backend tupled in.
Can be used to specify what file the url is added to. This can be used to
override the default filename that is used when adding an url, which is
based on the url. Or, when the file already exists, the url is recorded as
another location of the file.
Many functions took the repo as their first parameter. Changing it
consistently to be the last parameter allows doing some useful things with
currying, that reduce boilerplate.
In particular, g <- gitRepo is almost never needed now, instead
use inRepo to run an IO action in the repo, and fromRepo to get
a value from the repo.
This also provides more opportunities to use monadic and applicative
combinators.
This new approach allows filtering out checks from the default set that are
not appropriate for a command, rather than having to list every check
that is appropriate. It also reduces some boilerplate.
Haskell does not define Eq for functions, so I had to go a long way around
with each check having a unique id. Meh.
