No behavior changes (hopefully), just adding SeekInput and plumbing it
through to the JSON display code for later use.
Over the course of 2 grueling days.
withFilesNotInGit reimplemented in terms of seekHelper
should be the only possible behavior change. It seems to test as
behaving the same.
Note that seekHelper dummies up the SeekInput in the case where
segmentPaths' gives up on sorting the expanded paths because there are
too many input paths. When SeekInput later gets exposed as a json field,
that will result in it being a little bit wrong in the case where
100 or more paths are passed to a git-annex command. I think this is a
subtle enough problem to not matter. If it does turn out to be a
problem, fixing it would require splitting up the input
parameters into groups of < 100, which would make git ls-files run
perhaps more than is necessary. May want to revisit this, because that
fix seems fairly low-impact.
The goal is to be able to run CommandStart in the main thread when -J is
used, rather than unncessarily passing it off to a worker thread, which
incurs overhead that is signficant when the CommandStart is going to
quickly decide to stop.
To do that, the message it displays needs to be displayed in the worker
thread, after the CommandStart has run.
Also, the change will mean that CommandStart will no longer necessarily
run with the same Annex state as CommandPerform. While its docs already
said it should avoid modifying Annex state, I audited all the
CommandStart code as part of the conversion. (Note that CommandSeek
already sometimes runs with a different Annex state, and that has not been
a source of any problems, so I am not too worried that this change will
lead to breakage going forward.)
The only modification of Annex state I found was it calling
allowMessages in some Commands that default to noMessages. Dealt with
that by adding a startCustomOutput and a startingUsualMessages.
This lets a command start with noMessages and then select the output it
wants for each CommandStart.
One bit of breakage: onlyActionOn has been removed from commands that used it.
The plan is that, since a StartMessage contains an ActionItem,
when a Key can be extracted from that, the parallel job runner can
run onlyActionOn' automatically. Then commands won't need to worry about
this detail. Future work.
Otherwise, this was a fairly straightforward process of making each
CommandStart compile again. Hopefully other behavior changes were mostly
avoided.
In a few cases, a command had a CommandStart that called a CommandPerform
that then called showStart multiple times. I have collapsed those
down to a single start action. The main command to perhaps suffer from it
is Command.Direct, which used to show a start for each file, and no
longer does.
Another minor behavior change is that some commands used showStart
before, but had an associated file and a Key available, so were changed
to ShowStart with an ActionItemAssociatedFile. That will not change the
normal output or behavior, but --json output will now include the key.
This should not break it for anyone using a real json parser.
This does not change the overall license of the git-annex program, which
was already AGPL due to a number of sources files being AGPL already.
Legally speaking, I'm adding a new license under which these files are
now available; I already released their current contents under the GPL
license. Now they're dual licensed GPL and AGPL. However, I intend
for all my future changes to these files to only be released under the
AGPL license, and I won't be tracking the dual licensing status, so I'm
simply changing the license statement to say it's AGPL.
(In some cases, others wrote parts of the code of a file and released it
under the GPL; but in all cases I have contributed a significant portion
of the code in each file and it's that code that is getting the AGPL
license; the GPL license of other contributors allows combining with
AGPL code.)
This is groundwork for nested seek loops, eg seeking over all files and
then performing commandActions on a list of remotes, which can be done
concurrently.
This commit was sponsored by Boyd Stephen Smith Jr. on Patreon.
Added annex.commitmessage config that can specify a commit message for the
git-annex branch instead of the usual "update".
This commit was supported by the NSF-funded DataLad project.
This is a work in progress. It compiles and is able to do basic command
dispatch, including git autocorrection, while using optparse-applicative
for the core commandline parsing.
* Many commands are temporarily disabled before conversion.
* Options are not wired in yet.
* cmdnorepo actions don't work yet.
Also, removed the [Command] list, which was only used in one place.
I've been disliking how the command seek actions were written for some
time, with their inversion of control and ugly workarounds.
The last straw to fix it was sync --content, which didn't fit the
Annex [CommandStart] interface well at all. I have not yet made it take
advantage of the changed interface though.
The crucial change, and probably why I didn't do it this way from the
beginning, is to make each CommandStart action be run with exceptions
caught, and if it fails, increment a failure counter in annex state.
So I finally remove the very first code I wrote for git-annex, which
was before I had exception handling in the Annex monad, and so ran outside
that monad, passing state explicitly as it ran each CommandStart action.
This was a real slog from 1 to 5 am.
Test suite passes.
Memory usage is lower than before, sometimes by a couple of megabytes, and
remains constant, even when running in a large repo, and even when
repeatedly failing and incrementing the error counter. So no accidental
laziness space leaks.
Wall clock speed is identical, even in large repos.
This commit was sponsored by an anonymous bitcoiner.
Eventually, git-annex might try running this after making changes to
a remote. I have not yet thought of a good way for it to tell which
remotes it needs to run it on though. It can't just do it when
shutting down a cached ssh connection, because ssh connection caching
is optional, and that would not handle local remotes not accessed over ssh
either.
