Done using a mode witness, which ensures it's fixed everywhere.
Fixing catFileKey was a bear, because git cat-file does not provide a
nice way to query for the mode of a file and there is no other efficient
way to do it. Oh, for libgit2..
Note that I am looking at tree objects from HEAD, rather than the index.
Because I cat-file cannot show a tree object for the index.
So this fix is technically incomplete. The only cases where it matters
are:
1. A new large file has been directly staged in git, but not committed.
2. A file that was committed to HEAD as a symlink has been staged
directly in the index.
This could be fixed a lot better using libgit2.
Ie, when there'a a conflicted merge we may get foo.variant-xxxx
created in a merge. If a second merge conflict occurs on that new file,
it was not falling back to putting in the whole key (which should stop
the merge conflicts happening for good, but is ugly).
There may be already staged changes from a prior `git annex add`,
so always commit.
Also, suppressed the commit output, since it contains noise due to
typechanged files in direct mode.
This is so git remotes on servers without git-annex installed can be used
to keep clients' git repos in sync.
This is a behavior change, but since annex-sync can be set to disable
syncing with a remote, I think it's acceptable.
* since this is a crippled filesystem anyway, git-annex doesn't use
symlinks on it
* so there's no reason to use the mixed case hash directories that we're
stuck using to avoid breaking everyone's symlinks to the content
* so we can do what is already done for all bare repos, and make non-bare
repos on crippled filesystems use the all-lower case hash directories
* which are, happily, all 3 letters long, so they cannot conflict with
mixed case hash directories
* so I was able to 100% fix this and even resuming `git annex add` in the
test case will recover and it will all just work.
Pass subcommand as a regular param, which allows passing git parameters
like -c before it. This was already done in the pipeing set of functions,
but not the command running set.
Refactored annex link code into nice clean new library.
Audited and dealt with calls to createSymbolicLink.
Remaining calls are all safe, because:
Annex/Link.hs: ( liftIO $ createSymbolicLink linktarget file
only when core.symlinks=true
Assistant/WebApp/Configurators/Local.hs: createSymbolicLink link link
test if symlinks can be made
Command/Fix.hs: liftIO $ createSymbolicLink link file
command only works in indirect mode
Command/FromKey.hs: liftIO $ createSymbolicLink link file
command only works in indirect mode
Command/Indirect.hs: liftIO $ createSymbolicLink l f
refuses to run if core.symlinks=false
Init.hs: createSymbolicLink f f2
test if symlinks can be made
Remote/Directory.hs: go [file] = catchBoolIO $ createSymbolicLink file f >> return True
fast key linking; catches failure to make symlink and falls back to copy
Remote/Git.hs: liftIO $ catchBoolIO $ createSymbolicLink loc file >> return True
ditto
Upgrade/V1.hs: liftIO $ createSymbolicLink link f
v1 repos could not be on a filesystem w/o symlinks
Audited and dealt with calls to readSymbolicLink.
Remaining calls are all safe, because:
Annex/Link.hs: ( liftIO $ catchMaybeIO $ readSymbolicLink file
only when core.symlinks=true
Assistant/Threads/Watcher.hs: ifM ((==) (Just link) <$> liftIO (catchMaybeIO $ readSymbolicLink file))
code that fixes real symlinks when inotify sees them
It's ok to not fix psdueo-symlinks.
Assistant/Threads/Watcher.hs: mlink <- liftIO (catchMaybeIO $ readSymbolicLink file)
ditto
Command/Fix.hs: stopUnless ((/=) (Just link) <$> liftIO (catchMaybeIO $ readSymbolicLink file)) $ do
command only works in indirect mode
Upgrade/V1.hs: getsymlink = takeFileName <$> readSymbolicLink file
v1 repos could not be on a filesystem w/o symlinks
Audited and dealt with calls to isSymbolicLink.
(Typically used with getSymbolicLinkStatus, but that is just used because
getFileStatus is not as robust; it also works on pseudolinks.)
Remaining calls are all safe, because:
Assistant/Threads/SanityChecker.hs: | isSymbolicLink s -> addsymlink file ms
only handles staging of symlinks that were somehow not staged
(might need to be updated to support pseudolinks, but this is
only a belt-and-suspenders check anyway, and I've never seen the code run)
Command/Add.hs: if isSymbolicLink s || not (isRegularFile s)
avoids adding symlinks to the annex, so not relevant
Command/Indirect.hs: | isSymbolicLink s -> void $ flip whenAnnexed f $
only allowed on systems that support symlinks
Command/Indirect.hs: whenM (liftIO $ not . isSymbolicLink <$> getSymbolicLinkStatus f) $ do
ditto
Seek.hs:notSymlink f = liftIO $ not . isSymbolicLink <$> getSymbolicLinkStatus f
used to find unlocked files, only relevant in indirect mode
Utility/FSEvents.hs: | Files.isSymbolicLink s = runhook addSymlinkHook $ Just s
Utility/FSEvents.hs: | Files.isSymbolicLink s ->
Utility/INotify.hs: | Files.isSymbolicLink s ->
Utility/INotify.hs: checkfiletype Files.isSymbolicLink addSymlinkHook f
Utility/Kqueue.hs: | Files.isSymbolicLink s = callhook addSymlinkHook (Just s) change
all above are lower-level, not relevant
Audited and dealt with calls to isSymLink.
Remaining calls are all safe, because:
Annex/Direct.hs: | isSymLink (getmode item) =
This is looking at git diff-tree objects, not files on disk
Command/Unused.hs: | isSymLink (LsTree.mode l) = do
This is looking at git ls-tree, not file on disk
Utility/FileMode.hs:isSymLink :: FileMode -> Bool
Utility/FileMode.hs:isSymLink = checkMode symbolicLinkMode
low-level
Done!!
This fixes a problem I was seeing in the assistant where two remotes would
attempt to sync with one another at the same time, and both failed pushing
the diverged git-annex branch. Then when both tried to resolve the failed
push, they each modified their git-annex branch, which again each blocked
the other from pushing into it. The result was that the git-annex
branches were perpetually diverged (despite having the same content!) and
once the assistant fell into this trap, it couldn't get out and always
had to do the slow push/fail/pull/merge/push/fail cycle.
Found a very cheap way to determine when a disconnected remote has
diverged, and has new content that needs to be transferred: Piggyback on
the git-annex branch update, which already checks for divergence.
However, this does not check if new content has appeared locally while
disconnected, that should be transferred to the remote.
Also, this does not handle cases where the two git repos are in sync,
but their content syncing has not caught up yet.
This code could have its efficiency improved:
* When multiple remotes are synced, if any one has diverged, they're
all queued for transfer scans.
* The transfer scanner could be told whether the remote has new content,
the local repo has new content, or both, and could optimise its scan
accordingly.
This commit includes a paydown on technical debt incurred two years ago,
when I didn't know that it was bad to make custom Read and Show instances
for types. As the routes need Read and Show for Transfer, which includes a
Key, and deriving my own Read instance of key was not practical,
I had to finally clean that up.
So the compact Key read and show functions are now file2key and key2file,
and Read and Show are now derived instances.
Changed all code that used the old instances, compiler checked.
(There were a few places, particularly in Command.Unused, and the test
suite where the Show instance continue to be used for legitimate
comparisons; ie show key_x == show key_y (though really in a bloom filter))
While this word may be less familiar to some users, it avoids the
connotation that version 2 is better than version 1, which is wrong
when the two variants were conflicting.
Note that, since this always pushes branch synced/master to the remote, it
assumes that master has already gotten all the commits that are on the
remote merged in. Otherwise, fast-forward prevention may prevent the push.
That's probably ok, because the next stage is to automatically detect
incoming pushes and merge.
This has two benefits.
1. When a lot of refs are going to be received, get them via lower cost
connection when possible.
2. Allows ctrl-c of sync after the cheaper remotes have been pulled from
(or pushed to).
Now changes are staged into the branch's index, but not committed,
which avoids growing a large journal. And sync and merge always
explicitly commit, ensuring that even when they do nothing else,
they commit the staged changes.
Added a flag file to indicate that the branch's journal contains
uncommitted changes. (Could use git ls-files, but don't want to run
that every time.)
In the future, this ability to have uncommitted changes staged in the
journal might be used on remotes after a series of oneshot commands.
With --fast, unavailable local remotes are filtered out of the fast set.
This way, if there are local remotes, --fast always acts only on them,
and if none are mounted, acts on nothing. This consistency is better
than --fast acting on different remotes depending on what's mounted.
Some changes to make automated syncing nicer. Merge from both the remote's
$branch and its synced/$branch; either could have new changes. Create
synced/$branch on the remote when pushing.
This optimises away the need to run anything in some common cases.
It's particularly useful on push; no need to push if the tracking branch
we just pulled is the same as the branch we're going to push.
The other uses of it can all be simplified using Git.Ref.base,
Git.Ref.under, and show.
In some cases, describe was being used to shorten the branch name
unnecessarily, and I instead pass the fully qualified name to git.
git-annex normally only runs the branch update once per run, for speed, but
since this fetches new remote git-annex tracking branches, they need to be
merged in after that fetch. An earlier call to Remote.byName was causing
the update to run before the fetch sometimes, but it could have been
anything. Just force the update to happen in the right place.
