Sped up seeking for files to operate on, when using options like --copies
or --in, by around 20%.
Benchmark showed an increase for --copies from 155 seconds to 121
seconds, and --in remote will be similar to that.
For --in here, the speedup was less, 5-10% or so.
(both warm cache)
This commit was sponsored by Jack Hill on Patreon.
Sped up seeking to around twice as fast, by avoiding a pass over the
worktree files when preferred content expressions of the local repo and
remotes don't use include=/exclude=.
Thanks to Lukey for identifying the optimisation.
This commit was sponsored by Brock Spratlen on Patreon.
matchNeedsFileContent is not used yet, but shows how to add information
about terminals. That one would be needed for
https://git-annex.branchable.com/todo/sync_fast_import/
Note the tricky bit in Annex.FileMatcher.call where it folds over the
included matcher to propagate the information.
This commit was sponsored by Svenne Krap on Patreon.
getPid returns Nothing if the process has already been stopped, and in that
case, the pid will not be displayed. I think that would only happen if
waitForProcess or similar gets called more than once on the same process
handle though.
getPid on unix has an overhead of only a MVar read. On Windows it needs to
make a syscall, so will be probably more expensive. While the added expense
happens even when debug logging is disabled, it should be small enough
compared with the overhead of starting a process that it's not a problem.
(It does occur to me that a debugM that took an IO String could only run it
when debugging is really enabled, which would improve performance. It does
not seem possible to use the current hslogger interface to do that though;
it does not expose the information that would be needed.)
With some hints for the user for what to do.
Took care to avoid changing the json output. It would have been ok to add
the new separated lists to it, in addition to the old list, but I didn't
do that because I didn't see much point.
add, addurl, importfeed, import: Added --no-check-gitignore option
for finer grained control than using --force.
(--force is used for too many different things, and at least one
of these also uses it for something else. I would like to reduce
--force's footprint until it only forces drops or a few other data
losses. For now, --force still disables checking ignores too.)
addunused: Don't check .gitignores when adding files. This is a behavior
change, but I justify it by analogy with git add of a gitignored file
adding it, asking to add all unused files back should add them all back,
not skip some. The old behavior was surprising.
In Command.Lock and Command.ReKey, CheckGitIgnore False does not change
behavior, it only makes explicit what is done. Since these commands are run
on annexed files, the file is already checked into git, so git add won't
check ignores.
--batch combined with -J now runs batch requests concurrently for many
commands. Before, the combination was accepted, but did not enable
concurrency. Since the output of batch requests can be in any order, --json
with the new "input" field is recommended to be used, to determine which
batch request each response corresponds to.
If --json is not used, batch mode still runs concurrently, using the usual
concurrent-output. That will not be very useful for most batch mode users,
probably, but who knows.
If a program was using --batch -J before, and was parsing non-json output,
this could break it. But, it was relying on git-annex not supporting
concurrency despite it being enabled, so it should have expected concurrent
output. So, I think that's ok.
annex.jobs does not enable concurrency in --batch mode, because that would
confuse programs that use --batch but don't expect concurrency.
So these special remotes are always supported.
IIRC these build flags were added because the dep chains were a bit too
long, or perhaps because the libraries were not available in Debian stable,
or something like that. That was long ago, those reasons no longer apply,
and users get confused when builtin special remotes are not available, so
it seems best to remove the build flags now.
If this does cause a problem it can be reverted of course..
This commit was sponsored by Jochen Bartl on Patreon.
Works better with automatic merge conflict resolution than git's ususual
default of "conflict".
This is not done when automatic merge conflict resolution is disabled.
This commit was sponsored by Mark Reidenbach on Patreon.
This case was handled by cleanConflictCruft, but only when the annexed
file's object was present. When not present, it left the annexed file
with the original name, not checked into git, while adding the variant
file. So, add an explicit deletion of the deleted file in this case.
My specific case where this happened actually involves
merge.directoryRenames=conflict. After a merge involving that,
the situation was the file appears as "added by them", because that
caused the file that they added to be moved into a directory we renamed.
That case is the same as them adding a modified version of the file,
while we deleted it. (Except for the history of the file, since it's a
new file, but this doesn't look at history.)
This commit was sponsored by Boyd Stephen Smith Jr. on Patreon.
This does not actually change how the merge conflict is resolved when
one side deleted the file, but it was not documented before, and I think
it only worked by accident.
This commit was sponsored by Brett Eisenberg on Patreon.
