nukeFile replaced with removeWhenExistsWith removeLink, which allows
using RawFilePath. Utility.Directory cannot use RawFilePath since setup
does not depend on posix.
This commit was sponsored by Graham Spencer on Patreon.
No behavior changes (hopefully), just adding SeekInput and plumbing it
through to the JSON display code for later use.
Over the course of 2 grueling days.
withFilesNotInGit reimplemented in terms of seekHelper
should be the only possible behavior change. It seems to test as
behaving the same.
Note that seekHelper dummies up the SeekInput in the case where
segmentPaths' gives up on sorting the expanded paths because there are
too many input paths. When SeekInput later gets exposed as a json field,
that will result in it being a little bit wrong in the case where
100 or more paths are passed to a git-annex command. I think this is a
subtle enough problem to not matter. If it does turn out to be a
problem, fixing it would require splitting up the input
parameters into groups of < 100, which would make git ls-files run
perhaps more than is necessary. May want to revisit this, because that
fix seems fairly low-impact.
Added annex.skipunknown git config, that can be set to false to change the
behavior of commands like `git annex get foo*`, to not skip over files/dirs
that are not checked into git and are explicitly listed in the command
line.
Significant complexity was needed to handle git-annex add, which uses some
git ls-files calls, but needs to not use --error-unmatch because of course
the files are not known to git.
annex.skipunknown is planned to change to default to false in a
git-annex release in early 2022. There's a todo for that.
Git will eventually switch to sha2 and there will not be one single
shaSize anymore, but two (40 and 64).
Changed all parsers for git plumbing output to support both sizes of
shas.
One potential problem this does not deal with is, if somewhere in
git-annex it reads two shas from different sources, and compares them
to see if they're the same sha, it would fail if they're sha1 and sha256
of the same value. I don't know if that will really be a concern.
Adds a dependency on filepath-bytestring, an as yet unreleased fork of
filepath that operates on RawFilePath.
Git.Repo also changed to use RawFilePath for the path to the repo.
This does eliminate some RawFilePath -> FilePath -> RawFilePath
conversions. And filepath-bytestring's </> is probably faster.
But I don't expect a major performance improvement from this.
This is mostly groundwork for making Annex.Location use RawFilePath,
which will allow for a conversion-free pipleline.
The goal is to be able to run CommandStart in the main thread when -J is
used, rather than unncessarily passing it off to a worker thread, which
incurs overhead that is signficant when the CommandStart is going to
quickly decide to stop.
To do that, the message it displays needs to be displayed in the worker
thread, after the CommandStart has run.
Also, the change will mean that CommandStart will no longer necessarily
run with the same Annex state as CommandPerform. While its docs already
said it should avoid modifying Annex state, I audited all the
CommandStart code as part of the conversion. (Note that CommandSeek
already sometimes runs with a different Annex state, and that has not been
a source of any problems, so I am not too worried that this change will
lead to breakage going forward.)
The only modification of Annex state I found was it calling
allowMessages in some Commands that default to noMessages. Dealt with
that by adding a startCustomOutput and a startingUsualMessages.
This lets a command start with noMessages and then select the output it
wants for each CommandStart.
One bit of breakage: onlyActionOn has been removed from commands that used it.
The plan is that, since a StartMessage contains an ActionItem,
when a Key can be extracted from that, the parallel job runner can
run onlyActionOn' automatically. Then commands won't need to worry about
this detail. Future work.
Otherwise, this was a fairly straightforward process of making each
CommandStart compile again. Hopefully other behavior changes were mostly
avoided.
In a few cases, a command had a CommandStart that called a CommandPerform
that then called showStart multiple times. I have collapsed those
down to a single start action. The main command to perhaps suffer from it
is Command.Direct, which used to show a start for each file, and no
longer does.
Another minor behavior change is that some commands used showStart
before, but had an associated file and a Key available, so were changed
to ShowStart with an ActionItemAssociatedFile. That will not change the
normal output or behavior, but --json output will now include the key.
This should not break it for anyone using a real json parser.
This does not change the overall license of the git-annex program, which
was already AGPL due to a number of sources files being AGPL already.
Legally speaking, I'm adding a new license under which these files are
now available; I already released their current contents under the GPL
license. Now they're dual licensed GPL and AGPL. However, I intend
for all my future changes to these files to only be released under the
AGPL license, and I won't be tracking the dual licensing status, so I'm
simply changing the license statement to say it's AGPL.
(In some cases, others wrote parts of the code of a file and released it
under the GPL; but in all cases I have contributed a significant portion
of the code in each file and it's that code that is getting the AGPL
license; the GPL license of other contributors allows combining with
AGPL code.)
This is groundwork for nested seek loops, eg seeking over all files and
then performing commandActions on a list of remotes, which can be done
concurrently.
This commit was sponsored by Boyd Stephen Smith Jr. on Patreon.
ghc 8 added backtraces on uncaught errors. This is great, but git-annex was
using error in many places for a error message targeted at the user, in
some known problem case. A backtrace only confuses such a message, so omit it.
Notably, commands like git annex drop that failed due to eg, numcopies,
used to use error, so had a backtrace.
This commit was sponsored by Ethan Aubin.
Backend.lookupFile is changed to always fall back to catKey when
operating on a file that's not a symlink.
catKey is changed to understand pointer files, as well as annex symlinks.
Before, catKey needed a file mode witness, to be sure it was looking at a
symlink. That was complicated stuff. Now, it doesn't actually care if a
file in git is a symlink or not; in either case asking git for the content
of the file will get the pointer to the key.
This does mean that git-annex will treat a link
foo -> WORM--bar as a git-annex file, and also treats
a regular file containing annex/objects/WORM--bar as a git-annex file.
Calling catKey could make git-annex commands need to do more work than
before. This would especially be the case if a repo contained many regular
files, and only a few annexed files, as now git-annex will need to ask
git about the contents of the regular files.
This is a work in progress. It compiles and is able to do basic command
dispatch, including git autocorrection, while using optparse-applicative
for the core commandline parsing.
* Many commands are temporarily disabled before conversion.
* Options are not wired in yet.
* cmdnorepo actions don't work yet.
Also, removed the [Command] list, which was only used in one place.
