Done using a mode witness, which ensures it's fixed everywhere.
Fixing catFileKey was a bear, because git cat-file does not provide a
nice way to query for the mode of a file and there is no other efficient
way to do it. Oh, for libgit2..
Note that I am looking at tree objects from HEAD, rather than the index.
Because I cat-file cannot show a tree object for the index.
So this fix is technically incomplete. The only cases where it matters
are:
1. A new large file has been directly staged in git, but not committed.
2. A file that was committed to HEAD as a symlink has been staged
directly in the index.
This could be fixed a lot better using libgit2.
Note that it would be possible to extend the display to show all
repositories. But there can be a lot of repositories that are not set up as
remotes, and it would significantly clutter the display to show them all.
Since we're not showing all repositories, it's not worth trying to show
numcopies count either.
I decided to embrace these limitations and call the command remotes.
This is a git-remote-gcrypt encrypted special remote. Only sending files
in to the remote works, and only for local repositories.
Most of the work so far has involved making initremote work. A particular
problem is that remote setup in this case needs to generate its own uuid,
derivied from the gcrypt-id. That required some larger changes in the code
to support.
For ssh remotes, this will probably just reuse Remote.Rsync's code, so
should be easy enough. And for downloading from a web remote, I will need
to factor out the part of Remote.Git that does that.
One particular thing that will need work is supporting hot-swapping a local
gcrypt remote. I think it needs to store the gcrypt-id in the git config of the
local remote, so that it can check it every time, and compare with the
cached annex-uuid for the remote. If there is a mismatch, it can change
both the cached annex-uuid and the gcrypt-id. That should work, and I laid
some groundwork for it by already reading the remote's config when it's
local. (Also needed for other reasons.)
This commit was sponsored by Daniel Callahan.
The second commit had some bad refs which resulted in the race detection
code running. But that commit was unnecessary anyway, it only was there to
merge in the other refs.
Wrote nice pure transition calculator, and ugly code to stage its results
into the git-annex branch. Also had to split up several Log modules
that Annex.Branch needed to use, but that themselves used Annex.Branch.
The transition calculator is limited to looking at and changing one file at
a time. While this made the implementation relatively easy, it precludes
transitions that do stuff like deleting old url log files for keys that are
being removed because they are no longer present anywhere.
Having one module that knows about all the filenames used on the branch
allows working back from an arbitrary filename to enough information about
it to implement dropping dead remotes and doing other log file compacting
as part of a forget transition.
Works, more or less. --dead is not implemented, and so far a new branch
is made, but keys no longer present anywhere are not scrubbed.
git annex sync fails to push the synced/git-annex branch after a forget,
because it's not a fast-forward of the existing synced branch. Could be
fixed by making git-annex sync use assistant-style sync branches.
The reversion was that, if a file was git rm'd, but still in branches, it
would not be seen as used. Looking at both the added and the removed (or
changed) files from the diff-index is a cheap way to fix that.
Instead of populating the second-level Bloom filter with every key
referenced in every Git reference, consider only those which differ
from what's referenced in the index.
Incidentaly, unlike with its old behavior, staged
modifications/deletion/... will now be detected by 'unused'.
Credits to joeyh for the algorithm. :-)
When quvi is installed, git-annex addurl automatically uses it to detect
when an page is a video, and downloads the video file.
web special remote: Also support using quvi, for getting files,
or checking if files exist in the web.
This commit was sponsored by Mark Hepburn. Thanks!
This is a simple approach for setting up a mirroring repository.
It will work with any type of remotes.
Mirror --from is more expensive than mirror --to in general.
OTOH, mirror --from will get the file from any remote that has it, not only
the named mirror remote. And if the named mirror remote is not the fastest
available remote with a file, that can speed things up.
It would be possible to make the assistant or watch command do a more
dynamic mirroring, that didn't need to scan every time.
Note that --deduplicate currently checksums each file twice,
once to see if it's a known key, and once when importing it.
Perhaps this could be revisited and the extra checksum gotten rid of,
at the cost of not locking down the file when adding it.
Started with a problem when running addurl on a really long url,
because the whole url is munged into the filename. Ended up doing
a fairly extensive review for places where filenames could get too large,
although it's hard to say I'm not missed any..
Backend.Url had a 128 character limit, which is fine when the limit is 255,
but not if it's a lot shorter on some systems. So check the pathconf()
limit. Note that this could result in fromUrl creating different keys
for the same url, if run on systems with different limits. I don't see
this is likely to cause any problems. That can already happen when using
addurl --fast, or if the content of an url changes.
Both Command.AddUrl and Backend.Url assumed that urls don't contain a
lot of multi-byte unicode, and would fail to truncate an url that did
properly.
A few places use a filename as the template to make a temp file.
While that's nice in that the temp file name can be easily related back to
the original filename, it could lead to `git annex add` failing to add a
filename that was at or close to the maximum length.
Note that in Command.Add.lockdown, the template is still derived from the
filename, just with enough space left to turn it into a temp file.
This is an important optimisation, because the assistant may lock down
a bunch of files all at once, and using the same template for all of them
would cause openTempFile to iterate through the same set of names,
looking for an unused temp file. I'm not very happy with the relatedTemplate
hack, but it avoids that slowdown.
Backend.WORM does not limit the filename stored in the key.
I have not tried to change that; so git annex add will fail on really long
filenames when using the WORM backend. It seems better to preserve the
invariant that a WORM key always contains the complete filename, since
the filename is the only unique material in the key, other than mtime and
size. Since nobody has complained about add failing (I think I saw it
once?) on WORM, probably it's ok, or nobody but me uses it.
There may be compatability problems if using git annex addurl --fast
or the WORM backend on a system with the 255 limit and then trying to use
that repo in a system with a smaller limit. I have not tried to deal with
those.
This commit was sponsored by Alexander Brem. Thanks!
When there's no extension, don't use "none", but "".
When there is an extension, it starts with a dot, so don't put a redundant
dot in the default format.
