When a nonexistant file is passed to a command and --json-error-messages
is enabled, output a JSON object indicating the problem.
(But git ls-files --error-unmatch still displays errors about such files in
some situations.)
I don't like the duplication of the name of the command introduced by this,
but I can't see a great way around it. One way would be to pass the Command
instead.
When json is not enabled, the stderr is unchanged. This is necessary
because some commands like find have custom output. So dislaying
"find foo not found" would be wrong. So had to complicate things with
toplevelFileProblem having different output with and without json.
When not using --json-error-messages but still using --json, it displays
the error to stderr, but does display a json object without the error. It
does have an errorid though. Unsure how useful that behavior is.
Sponsored-by: Dartmouth College's Datalad project
These are quite low-level, but still there is no point in displaying
escape sequences that have been embedded in a key to the terminal.
I think these are the only remaining commands that didn't use safe
output, except for cases where git-annex is speaking a protocol to
itself.
Sponsored-by: Kevin Mueller on Patreon
No behavior changes (hopefully), just adding SeekInput and plumbing it
through to the JSON display code for later use.
Over the course of 2 grueling days.
withFilesNotInGit reimplemented in terms of seekHelper
should be the only possible behavior change. It seems to test as
behaving the same.
Note that seekHelper dummies up the SeekInput in the case where
segmentPaths' gives up on sorting the expanded paths because there are
too many input paths. When SeekInput later gets exposed as a json field,
that will result in it being a little bit wrong in the case where
100 or more paths are passed to a git-annex command. I think this is a
subtle enough problem to not matter. If it does turn out to be a
problem, fixing it would require splitting up the input
parameters into groups of < 100, which would make git ls-files run
perhaps more than is necessary. May want to revisit this, because that
fix seems fairly low-impact.
This removes all calls to inAnnex, except for some involving --batch.
It may be that the batch code could get a similar speedup, but I don't
know if people habitually pass a huge number of files through --batch
that git-annex does not need to do anything to process, so I skipped it
for now.
A few calls to ifAnnexed remain, and might be worth doing more to
convert. In particular, Command.Sync has one that would probably speed
it up by a good amount.
(also removed some dead code from Command.Lock)
Added annex.skipunknown git config, that can be set to false to change the
behavior of commands like `git annex get foo*`, to not skip over files/dirs
that are not checked into git and are explicitly listed in the command
line.
Significant complexity was needed to handle git-annex add, which uses some
git ls-files calls, but needs to not use --error-unmatch because of course
the files are not known to git.
annex.skipunknown is planned to change to default to false in a
git-annex release in early 2022. There's a todo for that.
The hoped for optimisation of CommandStart with -J did not materialize.
In fact, not runnign CommandStart in parallel is slower than -J3.
So, CommandStart are still run in parallel.
(The actual bad performance I've been seeing with -J in my big repo
has to do with building the remoteList.)
But, this is still progress toward making -J faster, because it gets rid
of the onlyActionOn roadblock in the way of making CommandCleanup jobs
run separate from CommandPerform jobs.
Added OnlyActionOn constructor for ActionItem which fixes the
onlyActionOn breakage in the last commit.
Made CustomOutput include an ActionItem, so even things using it can
specify OnlyActionOn.
In Command.Move and Command.Sync, there were CommandStarts that used
includeCommandAction, so output messages, which is no longer allowed.
Fixed by using startingCustomOutput, but that's still not quite right,
since it prevents message display for the includeCommandAction run
inside it too.
The goal is to be able to run CommandStart in the main thread when -J is
used, rather than unncessarily passing it off to a worker thread, which
incurs overhead that is signficant when the CommandStart is going to
quickly decide to stop.
To do that, the message it displays needs to be displayed in the worker
thread, after the CommandStart has run.
Also, the change will mean that CommandStart will no longer necessarily
run with the same Annex state as CommandPerform. While its docs already
said it should avoid modifying Annex state, I audited all the
CommandStart code as part of the conversion. (Note that CommandSeek
already sometimes runs with a different Annex state, and that has not been
a source of any problems, so I am not too worried that this change will
lead to breakage going forward.)
The only modification of Annex state I found was it calling
allowMessages in some Commands that default to noMessages. Dealt with
that by adding a startCustomOutput and a startingUsualMessages.
This lets a command start with noMessages and then select the output it
wants for each CommandStart.
One bit of breakage: onlyActionOn has been removed from commands that used it.
The plan is that, since a StartMessage contains an ActionItem,
when a Key can be extracted from that, the parallel job runner can
run onlyActionOn' automatically. Then commands won't need to worry about
this detail. Future work.
Otherwise, this was a fairly straightforward process of making each
CommandStart compile again. Hopefully other behavior changes were mostly
avoided.
In a few cases, a command had a CommandStart that called a CommandPerform
that then called showStart multiple times. I have collapsed those
down to a single start action. The main command to perhaps suffer from it
is Command.Direct, which used to show a start for each file, and no
longer does.
Another minor behavior change is that some commands used showStart
before, but had an associated file and a Key available, so were changed
to ShowStart with an ActionItemAssociatedFile. That will not change the
normal output or behavior, but --json output will now include the key.
This should not break it for anyone using a real json parser.
This does not change the overall license of the git-annex program, which
was already AGPL due to a number of sources files being AGPL already.
Legally speaking, I'm adding a new license under which these files are
now available; I already released their current contents under the GPL
license. Now they're dual licensed GPL and AGPL. However, I intend
for all my future changes to these files to only be released under the
AGPL license, and I won't be tracking the dual licensing status, so I'm
simply changing the license statement to say it's AGPL.
(In some cases, others wrote parts of the code of a file and released it
under the GPL; but in all cases I have contributed a significant portion
of the code in each file and it's that code that is getting the AGPL
license; the GPL license of other contributors allows combining with
AGPL code.)
This is groundwork for nested seek loops, eg seeking over all files and
then performing commandActions on a list of remotes, which can be done
concurrently.
This commit was sponsored by Boyd Stephen Smith Jr. on Patreon.
Chose to make this only handle files actively being downloaded, not temp
files for downloads that were interrupted or files that have been fully
downloaded.
This commit was sponsored by Ole-Morten Duesund on Patreon.
