This avoids some apparently otherwise unsolveable problems involving
races that resulted in the manifest listing bundles that were deleted.
Removed the annex-max-git-bundles config because it can't actually
result in deleting old bundles. It would still be possible to have a
config that controls how often to do a full push, which would avoid
needing to download too many bundles on clone, as well as needing to
checkpresent too many bundles in verifyManifest. But it would need a
different name and description.
Added a backup manifest key, which is used if the main manifest key is
not present. When uploading a new Manifest, it makes sure that it never
drops one key except when the other key is present.
It's entirely possible for the two manifest keys to get out of sync, due
to races. The main one wins when it's present, it is possible for the
main one being dropped to expose the backup one, which has a different
push recorded.
On push, first try to drop all outManifest keys listed in the current
manifest file, which resumes from an interrupted push that didn't
get a chance to delete those keys.
The new manifest gets its outManifest populated with the keys that were
in the old manifest, plus any of the keys that were unable to be
dropped.
Note that it would be possible for uploadManifest to skip dropping old
keys at all. The old keys would get dropped on the next push. But it
seems better to delete stuff immediately rather than waiting. And the
extra work is limited to push and typically is small.
A remote where dropKey always fails will result in an outManifest that
grows longer and longer. It would be possible to check if the remote
has appendonly = True and avoid populating the outManifest. Of course,
an appendonly remote will grow with every git push anyway. And currently
only Remote.GitLFS sets that, which can't be used as a git-remote-annex
remote anyway.
Implemented alternateJournal, which git-remote-annex
uses to avoid any writes to the git-annex branch while setting up
a special remote from an annex:: url.
That prevents the remote.log from being overwritten with the special
remote configuration from the url, which might not be 100% the same as
the existing special remote configuration.
And it prevents an overwrite deleting of other stuff that was
already in the remote.log.
Also, when the branch was created by git-remote-annex, only delete it
at the end if nothing else has been written to it by another command.
This fixes the race condition described in
797f27ab05, where git-remote-annex
set up the branch and git-annex init and other commands were
run at the same time and their writes to the branch were lost.
This turns out to only be necessary is edge cases. Most of the
time, git-annex unused --from remote doesn't see git-remote-annex keys
at all, because it does not record a location log for them.
On the other hand, git-annex unused does find them, since it does not
rely on the location log. And that's good because they're a local cache
that the user should be able to drop.
If, however, the user ran git-annex unused and then git-annex move
--unused --to remote, the keys would have a location log for that
remote. Then git-annex unused --from remote would see them, and would
consider them unused. Even when they are present on the special remote
they belong to. And that risks losing data if they drop the keys from
the special remote, but didn't expect it would delete git branches they
had pushed to it.
So, make git-annex unused --from skip git-remote-annex keys whose uuid
is the same as the remote.
I hope to support importtree=yes eventually, but it does not currently
work.
Added remote.<name>.allow-encrypted-gitrepo that needs to be set to
allow using it with encrypted git repos.
Note that even encryption=pubkey uses a cipher stored in the git repo
to encrypt the keys stored in the remote. While it would be possible to
not encrypt the GITBUNDLE and GITMANIFEST keys, and then allow using
encryption=pubkey, it doesn't currently work, and that would be a
complication that I doubt is worth it.
Updating the remote list needs the config to be written to the git-annex
branch, which was not done for good reasons. While it would be possible
to instead use Remote.List.remoteGen without writing to the branch, I
already have a plan to discard git-annex branch writes made by
git-remote-annex, so the simplest fix is to write the config to the
branch.
Sponsored-by: k0ld on Patreon
Put the annex objects in .git/annex/objects/ inside the export remote.
This way, when importing from the remote, they will be filtered out.
Note that, when importtree=yes, content identifiers are used, and this
means that pushing to a remote updates the git-annex branch. Urk.
Will need to try to prevent that later, but I already had a todo about
that for other reasons.
Untested!
Sponsored-By: Brock Spratlen on Patreon
Otherwise, it can be confusing to clone from a wrong url, since it fails
to download a manifest and so appears as if the remote exists but is empty.
Sponsored-by: Jack Hill on Patreon
This will eventually be used to recover from an interrupted fullPush
and drop the old bundle keys it was unable to delete.
Sponsored-by: Luke T. Shumaker on Patreon
Update its todo with remaining items.
Add changelog entry.
Simplified internals document to no longer be notes to myself, but
target users who want to understand how the data is stored
and might want to extract these repos manually.
Sponsored-by: Kevin Mueller on Patreon
Added to git-annex_proxies todo because this is something OpenNeuro
would need in order to use the git-annex proxy.
Sponsored-by: Dartmouth College's OpenNeuro project
Added rclone special remote, which can be used without needing to install
the git-annex-remote-rclone program. This needs a new version of rclone,
which supports "rclone gitannex".
This is implemented as a variant of an external special remote, that
runs "rclone gitannex" instead of the usual git-annex-remote- command.
Parameterized Remote.External to support that.
Sponsored-by: Luke T. Shumaker on Patreon
