Clean the standalone environment before running the su command
to run "sh". Otherwise, PATH leaked through, causing it to run
git-annex.linux/bin/sh, but GIT_ANNEX_DIR was not set,
which caused that script to not work:
[2022-10-26 15:07:02.145466106] (Utility.Process) process [938146] call: pkexec ["sh","-c","cd '/home/joey/tmp/git-annex.linux/r' && '/home/joey/tmp/git-annex.linux/git-annex' 'enable-tor' '1000'"]
/home/joey/tmp/git-annex.linux/bin/sh: 4: exec: /exe/sh: not found
Changed programPath to not use GIT_ANNEX_PROGRAMPATH,
but instead run the scripts at the top of GIT_ANNEX_DIR.
That works both when the standalone environment is set up, and when it's
not.
Sponsored-by: Kevin Mueller on Patreon
Make --batch mode handle unstaged annexed files consistently whether the
file is unlocked or not. Before this, a unstaged locked file
would have the symlink on disk examined and operated on in --batch mode,
while an unstaged unlocked file would be skipped.
Note that, when not in batch mode, unstaged files are skipped over too.
That is actually somewhat new behavior; as late as 7.20191114 a
command like `git-annex whereis .` would operate on unstaged locked
files and skip over unstaged unlocked files. That changed during
optimisation of CmdLine.Seek with apparently little fanfare or notice.
Turns out that rmurl still behaved that way when given an unstaged file
on the command line. It was changed to use lookupKeyStaged to
handle its --batch mode. That also affected its non-batch mode, but
since that's just catching up to the change earlier made to most
other commands, I have not mentioed that in the changelog.
It may be that other uses of lookupKey should also change to
lookupKeyStaged. But it may also be that would slow down some things,
or lead to unwanted behavior changes, so I've kept the changes minimal
for now.
An example of a place where the use of lookupKey is better than
lookupKeyStaged is in Command.AddUrl, where it looks to see if the file
already exists, and adds the url to the file when so. It does not matter
there whether the file is staged or not (when it's locked). The use of
lookupKey in Command.Unused likewise seems good (and faster).
Sponsored-by: Nicholas Golder-Manning on Patreon
While ErrorBusy and other exceptions were caught and the write retried for
up to 10 seconds, it was still possible for git-annex to eventually
give up and error out without writing to the database. Now it will retry
as long as necessary.
This does mean that, if one git-annex process is suspended just as sqlite
has locked the database for writing, another git-annex that tries to write
it it might get stuck retrying forever. But, that could already happen when
opening the sqlite database, which retries forever on ErrorBusy. This is an
area where git-annex is known to not behave well, there's a todo about the
general case of it.
Sponsored-by: Dartmouth College's Datalad project
When importing from versioned remotes, fix tracking of the content of
deleted files.
Only S3 supports versioning so far, so only it was affected.
But, the draft import/export interface for external remotes also seemed to
need a change, so that versionedExport could be set.
S3: Speed up importing from a large bucket when fileprefix= is set by only
asking for files under the prefix.
getBucket still returns the files with the prefix included, so the rest of
the fileprefix stripping still works unchanged.
Sponsored-by: Dartmouth College's DANDI project
move: Fix openFile crash with -J
This does make them a bit slower, although usually the log file is not
very big, so even when it's being rewritten, they will not block for
long taking the lock. Still, little slowdowns may add up when moving a lot
file files.
A less expensive fix would be to use something lower level than openFile
that does not check if the file is already open for write by another
thread. But GHC does not seem to provide anything convenient; even mkFD
checks for a writing thread.
fullLines is no longer necessary since these functions no longer will
read the file while it's being written.
Sponsored-by: Dartmouth College's DANDI project
* trust, untrust, semitrust, dead: Fix behavior when provided with
multiple repositories to operate on.
* trust, untrust, semitrust, dead: When provided with no parameters,
do not operate on a repository that has an empty name.
The man page and usage already indicated that multiple repos could be
provided to these commands, but they actually used unwords to combine
everything into string, and found a repo matching that string. This was
especially bad when no parameters resulted in the empty string and some
repo happened to have an empty description.
This does change the behavior, and it's possible someone relied on the
current behavior to eg, trust a repo by name with the name not quoted into
a single parameter. But fixing the empty string bug and matching the
documentation are worth breaking that usage.
Note that git-annex init/reinit do still unwords multiple parameters when
provided to them. That is inconsistent behavior, but it certianly seems
possible that something does run git-annex init with an unquoted
description, and I don't think it's worth breaking that just to make it more
consistent with these other commands.
Sponsored-by: Boyd Stephen Smith Jr. on Patreon
Avoids displaying warning about git-annex restage needing to be run in
situations where it does not.
Closing a handle flushes it anyway, so no need for an explict flush. The
handle does get closed twice, but that's fine, the second one does nothing.
Sponsored-by: Dartmouth College's DANDI project
