ghc 8.0.2 may make this unncessary, but it's not in a stackage version yet,
so put in a workaround.
Note that the linux builds already delete the RPATHs for similar reasons.
This commit was sponsored by Josh Taylor on Patreon.
When used with an older version of ssh, any ServerAliveInterval in
~/.ssh/config will be overridden by .git/annex/ssh.config.
This commit was sponsored by Josh Taylor on Patreon.
The Makefile was putting them in git-annex.linux/i18n/i18n, and so I18NPATH
did not point to the files. I think that on close enough to Debian systems,
localedef then fell back to using the system-wide locale files, while on
other systems it would fail to generate locales.
So that stalled transfers will be noticed within about 3 minutes,
even if TCPKeepAlive is disabled or doesn't work.
Rather than setting with -o, use -F with another config file,
so that any settings in ~/.ssh/config or /etc/ssh/ssh_config overrides this.
If a transfer fails for some reason, but some data managed to be sent, the
transfer will be retried. (The assistant already did this.)
Possible impacts:
* More ssh prompts if ssh needs to prompt for a password to connect to a
host, or is prompting about some other problem like a ssh key mismatch.
* More data transfer due to retrying, epecially when a remote does not
support resuming a transfer.
In the worst case, a lot of data will be transferred but it fails before
the end, and then all that data gets transferred again plus one byte more;
repeat until it manages to get the whole file.
Closes https://github.com/datalad/datalad/issues/1020
The use of runWriter in scanUnlockedFiles broke due to this change;
it failed with blocked indefinitely in mvar, because the database write
handle was taken while linkFromAnnex needed to also write to it (to update
the inode cache). So, switched to using a separate runWriter for each call
to addAssociatedFileFast. A little less efficient, but not greatly; the
writes should all still be cached.
When adding a tree like a/b/c/d when a/b already exists, fixes the bug that
the tree that got created was a/b/a/b/c/d
Just need to flatten out the top N directories of the tree that's being
grafted in, so we get the c/d part. This was complicated by the Tree
data type being a rose tree rather than a regular tree.
This commit was sponsored by Nick Daly on Patreon.
The modification flag was not being set when making modifications deep
in a tree, so parent trees were not updated to contain the modified tree.
Seems to have exposed another bug where the wrong filename gets grafted in.
This commit was sponsored by Brock Spratlen on Patreon.
An easy change now that supportedVersions is a list. Since v3 and v5 are
identical other than version number, just add v3 to the list.
This commit was sponsored by andrea rota.
.. and have to be checked to see if they are a pointed to an annexed file.
Cases where such memory use could occur included, but were not limited to:
- git commit -a of a large unlocked file (in v5 mode)
- git-annex adjust when a large file was checked into git directly
Generally, any use of catKey was a potential problem.
Fix by using git cat-file --batch-check to check size before catting.
This adds another git batch process, which is included in the CatFileHandle
for simplicity.
There could be performance impact, anywhere catKey is used. Particularly
likely to affect adjusted branch generation speed, and operations on
unlocked files in v6 mode. Hopefully since the --batch-check and
--batch read the same data, disk buffering will avoid most overhead.
Leaving only the overhead of talking to the process over the pipe and
whatever computation --batch-check needs to do.
This commit was sponsored by Bruno BEAUFILS on Patreon.
* sync: Previously, when run in a branch with a slash in its name,
such as "foo/bar", the sync branch was "synced/bar". That conflicted
with the sync branch used for branch "bar", so has been changed to
"synced/foo/bar".
* adjust: Previously, when adjusting a branch with a slash in its name,
such as "foo/bar", the adjusted branch was "adjusted/bar(unlocked)".
That conflicted with the adjusted branch used for branch "bar",
so has been changed to "adjusted/foo/bar(unlocked)"
* Also, running sync in an adjusted branch did not correctly sync
changes back to the parent branch when it had a slash in its name.
This bug has been fixed.
Eliminate use of Git.Ref.under and Git.Ref.basename; using
Git.Ref.underBase and Git.Ref.base make everything handle deep branches
correctly.
Probably noone was adjusting deep branches, and v6 is still experimental
anyway, so I'm not going to worry about the mess that was left by that bug.
In the case of git-annex sync, using a fixed git-annex with an old unfixed
one will mean they use different sync branches for a deep branch, and so
they may stop syncing until the old one is upgraded. However, that's only
a problem when syncing between repositories without going via a central
bare repository. Added a warning about this to the CHANGELOG, but it's
probably not going to affect many people at all.
This commit was sponsored by Riku Voipio.
And any other messages that might be output before a command starts.
Fixes a reversion introduced in version 5.20150727.
During the optparse-applicative conversion, I needed a place to run
per-command global option setters, and I made it get run during the seek stage. But
that is too late to have --json and --quiet disable output produced in the
check stage. Fix is just to run those per-command global option setters at
the same time as the all-command global option setters.
This commit was sponsored by Thom May.
