When a page is loaded, the javascript requests an notification url, and
does long polling on the url to be informed of changes. But if a change
occured before the notification url was requested, it would not be notified
of that change, and so the page display would not update.
I fixed this by *always* updating the page display after it gets
the notification url. This is extra work, but the overhead is not noticable
in the other overhead of loading a page.
(A nicer way would be to somehow record the version of a page initially
loaded, and then compare it with the current version when getting the
notification url, and only force an update if it's changed. But getting
the "version" of the different parts of the page that use long polling
is difficult.)
Like the old one, but does not mention which remotes are scanned.
I think this is less confusing, as it does not imply the remotes
were somehow accessed (which they are not; inaccessible remotes
can be scanned.)
If transferkey crashes or even fails to run, the TransferWatcher will not
see the transfer info file be created, so will not remove the transfer
from the list of active transfers. This causes the list to grow
continually, and all active transfers are displayed in the webapp. So, put
in a guard.
I assume that transferkey will not exit 0 while neglecting to clean up.
Rather than forking a git-annex transferkey only to have it fail,
just immediately record the failed transfer (so when the drive is plugged
in, the scan will retry it).
This may work around google talk's horrible presence handling, in which
clients often don't learn about other clients, at least when using the same
account. This way, every time we start a git push over xmpp, we'll waste
bandwidth asking clients to please try again to identify themselves.
Just before starting a transfer, do one last check that it's still
preferred content.
I was just doing this for uploads, as part of the smarter flood filling
bug, but realized it's also possible for a download that was preferred
content to change to not be before the download begins, so check that too.
Rather than wait a full second, which may be longer than needed, or too
short to get all the rename events, we start a mode where we wait 1/10th of
a second, and if there are Changes received, wait again. Basically we're
back in batch mode when this happens.
This cleaned up the code quite a bit; now the committer just looks at the
Change to see if it's a change that needs to have a transfer queued for it.
If I later want to add dropping keys for files that were removed, or
something like that, this should make it straightforward.
This also fixes a bug. In direct mode, moving a file out of an archive
directory failed to start a transfer to get its content. The problem
was that the file had not been committed to git yet, and so the transfer
code didn't want to touch it, since fileKey failed to get its key.
Only starting transfers after a commit avoids this problem.
This is not perfect, because on loss of connection, we do not currently
immediately detect it and stop the client. It has to time out, and then
the buddy list will clear.
The NetWatcher should detect disconnects too..
Noticed that, At startup or network reconnect, git push messages were sent,
often before presence info has been gathered, so were not sent to any
buddies.
To fix this, keep track of which buddies have seen such messages,
and when new presence is received from a buddy that has not yet seen it,
resend.
This is done only for push initiation messages, so very little data needs
to be stored.
This fixes the issue mentioned in the last commit.
Turns out just collecting UUID of clients behind a XMPP remote is
insufficient (although I should probably still do it for other reasons),
because a single remote repo might be connected via both XMPP and local
pairing. So a way is needed to know when a push was received from any
client using a given XMPP remote over XMPP, as opposed to via ssh.
Make manualPull send push requests over XMPP.
When reconnecting with remotes, those that are XMPP remotes cannot
immediately be pulled from and scanned, so instead maintain a set of
(probably) desynced remotes, and put XMPP remotes on it. (This set could be
used in other ways later, if we can detect we're out of sync with other
types of remotes.)
The merger handles detecting when a XMPP push is received from a desynced
remote, and triggers a scan then, if they have in fact diverged.
This has one known bug: A single XMPP remote can have multiple clients
behind it. When this happens, only the UUID of one client is recorded
as the UUID of the XMPP remote. Pushes from the other XMPP clients will not
trigger a scan. If the client whose UUID is expected responds to the push
request, it'll work, but when that client is offline, we're SOL.
Watcher wants to rewrite symlink to fix it. But in direct mode, the symlink
could be replaced at any time with file content that has finished being
transferred by some other process. So, just don't touch it.
FWIW, I audited the rest of the assistant for places where it removes
files, and the rest is ok. I have not audited the rest of git-annex.
assistant: Fix bug in direct mode that could occur when a symlink is moved
out of an archive directory, and resulted in the file not being set to
direct mode when it was transferred.
The bug was that the direct mode mapping was not up-to-date when the
transferrer finished. So, finding no direct mode place to store the object,
it was put into .git/annex in indirect mode.
To fix this, just make the watcher update the direct mode mapping to
include the new file before it starts the transfer. (Seems we don't need to
update it to remove the old file if the link was moved, because the direct
mode code will notice it's not present and the mapping gets updated for its
removal later.)
The reason this was a race, and was probably not seen often is because
the committer came along and updated the direct mode mapping as part of
adding the moved symlink. But when the file was sufficiently small or
the remote sufficiently fast, this could happen after the transfer
finished.
Looking through the git sources (documentation is unclear),
it seems commit doesn't ever trigger git-gc, mostly fetching and merging
seems to. I cannot easily override the setting in all those places, so
instead set gc.auto in git config when initializing a repository with
the assistant.
This does mean that the user cannot set gc.auto=0 and completely avoid
repacks, as the assistant does it daily. But, it only does it after there
are 100x the default number of loose objects, so this is probably not going
to be too annoying.
Pass subcommand as a regular param, which allows passing git parameters
like -c before it. This was already done in the pipeing set of functions,
but not the command running set.
