Apparently f2fs has a soft dependency on this driver, so if it's =m in
the kernel then let's make sure it's always in the initramfs since f2fs
is a supported filesystem.
Fixes https://gitlab.com/postmarketOS/pmaports/-/issues/2711
[ci:skip-build]: already built successfully in CI
How to boot from USB drives:
1. Make sure the extcon has OTG support and included in initramfs
2. Make sure the PMIC supports the power to OTG devices, and included in initramfs. Otherwise, a hub with external power supply is required.
3. Make sure module `usb-storage` is enabled in initramfs
4. `pmbootstrap install --sdcard=/dev/<usb_drive>`
- postmarketOS/pmbootstrap@942ee20789 is required to ignore sdcard check. Thanks @ollieparanoid for the patch.
5. `pmbootstrap flasher flash_kernel`
6. Insert the USB drive to OTG and boot
[ci:skip-build]: already built successfully in CI
Reading the `ifname` of a gadget that has not been configured with a UDC
succeeds with the content `(unnamed net_device)` instead of failing.
So we need to explicitly check that a UDC was configured before we read
the interface name.
Ref: #2648
Sometimes, there can be more than 10M of stuff collected for logging,
which breaks things.. bump the size to 32M which should still be small
enough for low end / old devices.
Signed-off-by: Caleb Connolly <caleb@postmarketos.org>
/dev/pmsg0 may be created by pstore driver. When it is available,
write logs into it so logs can be recovered through pstore after
a failed boot. This is useful for devices without console or hard
to get console.
Some devices take time to initialize storage, e.g. Qualcomm laptops
using ADSP need to load firmware firstly, and initramfs script does
not always manage to mount boot partition in time.
Unfortunately, there is no reliable way to reproduce the issue, but
this patch should fix cases like this.
Before this change the script assumed that the device has only one UDC.
However it is possible for a device to have multiple UDCs, in which case
the deviceinfo is the appropriate place to specify which one should be used.
This change adds an optional deviceinfo variable `deviceinfo_usb_network_udc`
to specify the UDC that should be used.
Also, before this change the script assumed the USB network interface name is
"usb0". But other gadget drivers like `g_cdc` can claim USB interfaces
before the initramfs script gets around to creating one for USB networking,
so the interface might be "usb1" or something else. The configfs gadget itself
can provide the actual interface name, so this change makes the script
use that.
Currently, when postmarketOS fails to boot up, retrieving any
information necessary to root cause the issue is non-trivial, requiring
building a custom initramfs with debug-shell enabled and then manually
copying out data.
Let's improve the situation by exporting logs automatically on boot
failure. This is safer than just exposing a root shell but still
provides a whole lot of useful info that should make duplicating and
triaging issues much easier for developers.
This commit implements the functionality and includes some generally
useful data. We then generate a README and expose files for each command/log
as well as an archive that can be easily attached to a GitLab issue.
To help with triaging, also record the version of the postmarketos-initramfs
package and hash the init.sh and init_functions.sh files.
For testing purposes, you can trigger the log recovery mode on-time by
creating an empty file named ".pmos_export_logs" in the /boot partition.
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
As described in [0] let's switch away from RNDIS and use NCM instead.
Since we cannot force all kernels to switch at the same time, let's keep
a fallback to RNDIS in the setup function.
We can also remove usb_f_rndis from modprobe as the module gets loaded
automatically when needed, but instead we need to load libcomposite
manually so that $configfs/usb_gadget gets created.
[0] https://gitlab.com/postmarketOS/pmaports/-/issues/1797
[ci:skip-build] already built successfully in CI
This shows the OS version (from /etc/os-release), e.g. "edge", on the splash
screen. os-release is a tiny text file, adding it to the initramfs doesn't seem
too bad, and having this information on the splash screen can be helpful.
Note that this uses "VERSION" and not "PRETTY_NAME" from the os-release file,
since the splash already shows "postmarketOS" (and the pretty name includes
that too), it seemed redundant and took up valuable display space.
[ci:skip-build]: already built successfully in CI
Enable using the postmarketOS initramfs for boot-testing devices, in
this scenario we don't care about some components like the splash, mdev,
or subpartitions, instead we want to run full udev (to load all devices)
and then run hooks. The ci hook will deadloop after running tests.
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Explicitly pull in the blkid package (we already added it to
00-initramfs-base.files), and replace uses of busybox findfs. Full fat
blkid supports PARTLABEL (so the /dev/disk/by-partlabel symlinks will
work consistently now), and has some nice optimisations that make the
lookup times a lot faster than busybox findfs.
[ci:skip-build]: already built successfully in CI
Drop in mdev.conf and the /lib/mdev/persistent-storage script, these
cause /dev/disk/by-* to be populated in the ramdisk, making it
possible to do look up partition by-label and by-partlabel for free,
compared to findfs which can take some time.
As a first optimisation based on this, check for some partitions using
these paths and prioritise them when looking for subpartitions. Drop the
first find_boot_partition call as it doesn't really save time over the
call in the while loop.
The mdev config also handles setting up /dev/null, /dev/random, etc, so
these don't have to be done manually.
These files aren't owned by mkinitfs, or used to configure mkinitfs, so
I think it makes sense that they belong in a dir specific to this
package instead of cluttering up mkinitfs's config dirs.
Mount /dev (and /run) in initramfs so util-linux switch_root can move
the mounts over to the new sysroot before changing root.
BusyBox switch_root doesn't even attempt to move anything so use
util-linux's switch_root for this.
Explicitly disable tests too...
Make it possible to load modules from the file installed by devicepkg-dev,
that will be there when extra modules are needed. This is coded in a
backwards-compatible way, so that it can be independent of the main modules
MR.
The code changes create a new function which takes a list of modules
and possibly a file (that should contain a list of modules too). The
idea is to be able to support also loading modules for initramfs-extra
in the future, and having a similar file would be more convenient than
extracting all the modules each time. In addition, the "[ -d /lib/modules]"
check has been removed. If there's no modules directory, as all
modules might be built-in, modprobe will fail, but that will not be
fatal. This will most likely only exclusively happen in some android
downstream kernel, so it should not be a big concern.
This appears to be an ancient leftover from the telnet-based FDE
unlocking mechanism that has been present many many years ago.
But since this was removed a while ago, it's time to also finally remove
telnetd from the initramfs.
As a preparation for #1836, move the sourcing of deviceinfo to its own
function. This should allow to have a single point in the whole of the
initramfs for the sourcing of the deviceinfo, instead of every script
that needs it sourcing it. This allows to change the way deviceinfo is
sourced in the future with a lot less effort.
This is a revert of the change introduced in 4eda0715 to support an
uncompressed initramfs-extra. osk-sdl support results in an initramfs-extra
that is too big for some devices with a small (traditional) /boot partition
Also see: https://gitlab.com/postmarketOS/pmaports/-/issues/2009
[ci:skip-build]: Already built successfully in CI
This package contains base file and module lists for the initramfs /
initramfs-extra archives, along with the init.sh
The primary reason for doing this is so that changes to these
files/lists can be properly versioned (in pkgver), and (re)building
mkinitfs itself is no longer required for these changes.
- Add base file list for initramfs. The dirs at path
/usr/share/postmarketos-mkinitfs/* are "new" in mkinitfs 2.0
- Install default modules to /usr/share
- Install system config to /usr/share/mkinifs
- Add base files for -extra archive
- Create user config dirs
- Update hook dirs in init.sh, change from mkinitfs 2.0
- Remove splash images, obsolete since pbsplash
- Support uncompressed initramfs-extra
