* Enable flash/torch LED (CONFIG_LEDS_QCOM_FLASH)
* Fix USB init when not plugged in during bootloader stage
[ci:skip-build] already built successfully in CI
Fix included in this build:
- Patch which sets GPIO pin for stk3311 as input
- ppp: don't reset 'display state of charge' (dsoc) to 0 on vbat low interrupt
[ci:skip-build]: already built successfully in CI
Update the omap kernel to stable 6.1 release. This commit also contains a patch that
fixes broken usb, which should only be needed for versions 5.19 to 6.1 as later
releases will have a proper fix merged.
[ci:skip-build]: already built successfully in CI
CONFIG_USB_GADGET=y
CONFIG_USB_DWC3_DUAL_ROLE=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_PLATFORM=y
CONFIG_USB_DWC2=y
remove un-necessary activated configs
[ci:skip-build]: already built successfully in CI
- Also enabled LRU_GEN by default like on the PinePhone OG
- Set Ext4 module to built-in as this currently is the main fs used for PPP.
Contains the following patch:
- pinephone pro: finished fix for LCD to make it refresh at precisely 60 Hz
[ci:skip-build]: already built successfully in CI
Add the CONFIG_DW9714 symbol to the PinephonePro defconfig.
The PinephonePro rear camera module uses the DW9714 VCM to drive the
lens, and a driver is required to successfully complete the media
graph probe sequence.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
In SDM845, the q6voice kernel driver connects modem and audio backends.
Callaudiod seems to switch to correct audio device and prepares it, however, the audio
device get's closed since no one from the userspace is actively listening to it.
This cuts the audio in call. As a workaround, I have added to script to disable the
suspend-on-idle pulseaudio module during calls, so the audio devices don't close automatically.
Includes the following changes:
- rebase onto rc4
- squash a few changes which were marked to get squashed/fixups
- dropped "wcd934x: use .prepare and .shutdown instead of .trigger"
- OP6 audio device tree changes
- revert of a DSI DCS commit[1], which caused havoc in unprepare
hooks of panel drivers
[1] - https://lore.kernel.org/linux-arm-msm/1892d0af-8aa4-dc03-887a-e44bb623b836@linaro.org/
Change-Id: I4790a278c0d35618ca824a036982769e66767ffd
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
Since 00648d0282dcca1da453c0b20d27e24bf901a854, the correct serial console name
is ttySx instead of the older ttyOx. Reflect this in cmdline passed to kernel
via u-boot
[ci:skip-build]: already built successfully in CI
Change-Id: Ice7c2942892eb0a173dcded835d5fac5a8f32066
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
[ci:skip-build]: already built successfully in CI
Update the ALSA UCM package for the SDM845 so the ALSA UCM configs for
the SHIFT6mq are included. Speaker, microphones, headset work fine in
HiFi mode. In Voice Call mode, the microphone works, but the earpiece is
still silent.
[ci:skip-build]: already built successfully in CI
q6voiced is a daemon to allow voice calls with the q6voice kernel
driver. Add its config so it can open the right audio device on the
SHIFT6mq during a call.
Explicitly set Fn key as Mod5. In xkeyboard-config up to 2.36, this was somehow
set implicitly, since it was working, although I am not sure where/how. In 2.37
it only works when specified.
[ci:skip-build]: already built successfully in CI
Since N900 rtc works fine, remove swclock from boot as it causes time to be set
wrong. Additionally, rtc device is set correctly in kernel, so remove old,
adjusted hwclock config.
Partially reverts pmaports 0e502a5139
[ci:skip-build]: already built successfully in CI
Venji10 is no longer involved in actively maintaining the package for more than a year plus.
Changing myself to be the maintainer and also updated my email id.
[ci:skip-build]: already built successfully in CI
Because of recent changes to kernel and alsa-ucm-conf,
the q6voiced device is changed.
Venji10 is no longer involved in actively maintaining the package for more than a year plus.
Changing myself to be the maintainer and also updated my email id.
Rebased our work on top of latest upstram alsa-ucm-conf.
The beryllium ucm conf is also reworked to fix wrong default audio device issue
and now headphones auto-switching on plugin also works as expected.
Adding myself as a co-maintainer for this package.
Change-Id: I360c60d1675c884c9e85cd95f940fa6cb4b75e83
Signed-off-by: Joel Selvaraj <joelselvaraj.oss@gmail.com>
Change-Id: I986b3401fd81ac18b7336f8f0be53e2cf4c4515c
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
Signed-off-by: Joel Selvaraj <joelselvaraj.oss@gmail.com>
