Having RMTFS at runlevel boot makes it start the modem too fast and causes
crashes. Move it to runlevel default with a post-install.
[ci:skip-build] already built successfully in CI
My engineering prototype 1 Gb pinetab is close to unusable,
so I can't use it to test pmOS. Also, PINE64 is no longer
selling these devices, and the ones that were sent previously
to some developers use different display panel anyway.
Martijn Braam and Dylan Van Assche agreed to maintain it.
[skip ci]
- Add SLPI to nonfree_firmware description
- Add touchscreen and fuel gauge modules to the initramfs in preparation for
osk-sdl and charging-sdl (or any new alternative) support
- Add pointercal file for osk-sdl
[ci:skip-vercheck]
Set package dependency "swclock-offset" to "soc-qcom-msm8916" and
"soc-qcom-sdm845".
These SoC's have a read-only real-time clock (RTC). The package
"swclock-offset" keeps an offset between the RTC and the system time.
Add the missing depends to add the GPU firmware to the initramfs
so that osk-sdl works properly, as well as the haptics driver.
Also make all logs go to UART, this will clean up the splash screen and
let developers with UART access debug the boot process.
[ci:skip-build] This MR was already built on CI
Add the missing depends for our soc package alsa ucm configs. Also add
the missing depends to add the GPU firmware to the initramfs so that
osk-sdl works properly!
Also enable logs and point them to UART, this will clean up the splash
screen and let any developers with UART attached to debug the boot
process.
The PMIC AXP803 sends an interrupt to the A64 CPU when the
battery is critical low. This wakes up the tablet at ~10%
battery level, but UPower wasn't configured to add upon
this interrupt as the action level was way lower.
Therefore, the PMIC performed a hard shutdown when the
battery level dropped further, which may cause data loss.
uboot-tools is provided by u-boot-tools but sometimes apk still gets
confused. This change prevents errors such as
pine64-pinephone:~$ sudo apk upgrade --verbose
WARNING: Failed to perform initial self-upgrade, continuing with full upgrade.
ERROR: unable to select packages:
uboot-tools (virtual):
provided by: u-boot-tools
required by: device-pine64-pinephone-0.25-r1[uboot-tools]
[ci:ignore-count]
[ci:skip-build]: already built in CI successfully
As of MR 2039, the kernel modules are now stripped (INSTALL_MOD_STRIP=1).
It turns out that this massively reduces their size so that including
the panel + touchscreen modules in the initfs still fits into the
partition. This allows the splash screen and osk-sdl to work correctly.
As of MR 2039, the kernel modules are now stripped (INSTALL_MOD_STRIP=1).
It turns out that this massively reduces their size so that including
the panel + touchscreen modules in the initfs still fits into the
partition. This allows the splash screen and osk-sdl to work correctly.
As of MR 2039, the kernel modules are now stripped (INSTALL_MOD_STRIP=1).
It turns out that this massively reduces their size so that including
the panel + touchscreen modules in the initfs still fits into the
partition. This allows the splash screen and osk-sdl to work correctly.
As of MR 2039, the kernel modules are now stripped (INSTALL_MOD_STRIP=1).
It turns out that this massively reduces their size so that including
the panel + touchscreen modules in the initfs still fits into the boot
partition. This allows the splash screen and osk-sdl to work correctly.
Make needed deviceinfo changes to support osk-sdl, add "quiet" to the
cmdline and bump the package version to 1.
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
[ci:skip-vercheck]
Make needed deviceinfo changes to support osk-sdl, add "quiet" to the
cmdline and bump the package version to 1.
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Add a subpackage to ensure that GPU firmware is included in initramfs so
that osk-sdl can work.
[ci:skip-vercheck]
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Resize the partition when using a pre-built image. We didn't notice that
this was missing, because N900 images are new and we only tested from
pmbootstrap install --sdcard, which already uses the full SD card size.
This allows loading nonfree fw from rootfs (/lib/firmware), to work
around: https://source.puri.sm/Librem5/linux-next/-/issues/290
This change will break wifi unless the nonfree
firmware-siliconlabs-rs9116 package is installed.
Actually the display in asus-me176c has a width of 800px, which means
that the splash screen isn't perfectly centered. Correct this in
deviceinfo to make it show up correctly.
Also, add configuration file for Phosh to reduce scaling a bit to 1.75.
It's kind of subjective but scaling = 2 definitely feels too large.
[ci:skip-build]: already built successfully in CI
