gzip results in a boot.img that's too big (over 8 MB) for e.g.
samsung-i9300, so let's replace it with something that produces
smaller kernels. With this, the entire boot.img is 6,3 MB (down
from 8MiB, or 8.5458944 MB) which leaves plenty of space on the
8 MB partition and prevents the recovery from being overwritten
when this kernel is flashed.
Tested and works on samsung-i9300.
[ci:skip-build] already built successfully in CI
This provides a mobile-friendly music player in the default
installation which is something that's currently lacking.
[ci:skip-vercheck]: _pmb_recommends change doesn't need pkgrel bump
The networkmanager hotspot needs to have DHCP input enabled on the wifi
interfaces so the temporary dnsmasq instance can work. The
networkmanager backend is also switched to the nftables one so it can
create the ad-hoc hotspot forwarding/masquerade table.
Proper fix for the monospace fonts seen when postmarketos-ondev is
installed without also installing osk-sdl. This doesn't happen anymore
with pmbootstrap install --ondev, because it will always pull in osk-sdl
again for other reasons. However, since postmarketos-ondev is using this
font, let's directly depend on it instead of having it pulled in as side
effect of also having osk-sdl installed.
And extend bootloader CMDLINE per default, giving us the option to
change the CMDLINE both via the kernel config and from samsung's
S-BOOT shell.
Note: the default console in exynos_defconfig (which this config is
based on) is ttySAC1, but all midas devices uses ttySAC2, so set it to
ttySAC2 instead. Also remove all other variables. They are not needed,
and (at least) root=/dev/ram0 seem to prevent us from booting pmos.
[ci:skip-build] already built successfully in CI
NymphCast is a FOSS Chromecast replacement (not a drop-in one though)
and allows you to "cast" audio and video to your device running the
nymphcast server. Plasma Bigscreen seems like an ideal use-case for this
so let's install and launch it by default. People can always uninstall
it anyways
This allows using lm_sensors to read temperature data on the pinebook
pro (and probably other devices too)
❯ sensors
gpu_thermal-virtual-0
Adapter: Virtual device
temp1: +41.1°C (crit = +95.0°C)
tcpm_source_psy_4_0022-i2c-4-22
Adapter: rk3x-i2c
in0: 5.00 V (min = +5.00 V, max = +5.00 V)
curr1: 2.50 A (max = +2.50 A)
cw2015_battery-i2c-4-62
Adapter: rk3x-i2c
in0: 4.24 V
curr1: 0.00 A
cpu_thermal-virtual-0
Adapter: Virtual device
temp1: +47.5°C (crit = +95.0°C)
nvme-pci-0100
Adapter: PCI adapter
Composite: +31.9°C (low = -273.1°C, high = +80.8°C)
(crit = +80.8°C)
Sensor 1: +31.9°C (low = -273.1°C, high = +65261.8°C)
Sensor 2: +37.9°C (low = -273.1°C, high = +65261.8°C)
[ci:skip-build] Already built on CI
5.13.5 had some rockchip-related fixes in the changelog, so I figured
why not upgrade to it.
These patches from Manjaro seem to be the bare minimum required to get
usb-c charging and device peripherial support working again (external
display still doesn't work)
[ci:skip-build] already built successfully in CI
llvm was left over from Martijn's efforts to reduce the kernel size
The drivers for external DP are enabled here, but all patches from
manjaro that deal with DP/typec alt mode, etc are dropped since they do
not solve anything on their own and may cause display instability
issues...
[ci:skip-build]: already built successfully in CI
prevent the creation of a fake NUMA node
saving a few CPU cycles each DRAM access:
[ 0.000000] NUMA: No NUMA configuration found
[ 0.000000] NUMA: Faking a node at ...
[ 0.000000] NUMA: NODE_DATA [mem 0xff9c2100-0xff9c3fff]
if you boot on QEMU make sure to review vCPU topology:
set socket to 1
This is needed to get ethernet working on most 64-bit sunxi boards.
Basically just synced with armv7 config a bit.
[ci:skip-build] already built successfully in CI
Install obex-capabilities and a modified DBus Service
for BlueZ's obexd when BlueZ OBEX support is installed.
UIs depending on BlueZ are now also depending on
bluez-obexd for OBEX support through various MRs at Alpine.
Anbox, nftables, and containers aren't set up for now because I'm not
sure how useful Anbox would be on devices using this SoC given that most
(all?) of them have around 1 GB of RAM, aren't very fast, and I have
heard that Anbox isn't very well-Asupported on ARMv7. As for nftables,
I don't want debug it at this time in case breaks something. Setting up
container support made the phone hang while booting, however that might
have been due to that I only booted the new kernel without getting the
new modules in the rootfs.
[ci:skip-build] already built successfully in CI
Pulseaudio is used by other graphical UIs to manage audio, so having it
installed for sway is useful for having audio working "out of the box"
[ci:skip-build] already built successfully in CI
This package used to be installed through osk-sdl, but now osk-sdl is only
installed when FDE is enabled, and so when it is not enabled the system has no
fonts to use, which means UIs like Sway and Weston have broken fonts. This
commit fixes the issue.
[ci:skip-build] already built successfully in CI
This adds a new 'UI' that includes networking support (network manager), firewall (by way
of postmarketos-base-ui), and anything else that will give a basic,
working image without any graphical UI.
The intention is for bpo to build this instead of the 'none' UI. 'none'
UI will continue to be around for mainlining and testing purposes.
