Protect script when ram_freq is not set
Safely load PSCI DTO to enable CPUidle driver: psci_idle
The PSCI DTO shall only be applied if TF-A & Crust
support CPU idle states [0]. Otherwise the CPU usage
will be at 100%. This will not be visible in top,
lead to overheating and battery drain.
Worst case scenario would lead to a fried chip if
the CPU thermal_zone does not work or is not enabled
in DTS.
[0] https://gitlab.com/postmarketOS/pmaports/-/issues/1901#note_1238456920
I have enough other devices to care about, and honestly haven't touched
my PinePhone in a while. Remove myself as Co-Maintainer from all
relevant packages.
[ci:skip-vercheck]: No rebuild necessary
[ci:skip-build]: Doesn't change resulting packages
Let /usr/share/alsa/ucm2/conf.d/simple-card/*.conf be a symlink,
as it is expected since alsa-lib 1.2.7.
Related: d6adde0e32
[ci:skip-build] already built successfully in CI
For the Biktorgj firmware the control/power file should be set to on
instead of auto. By matching on the serial number this only applies to
modems with the community firmware installed.
The package `device-pine64-pinephone-vccq-mod` installs a u-boot user script.
The user script was loaded at address 0x50100000 partially overwriting
the initramfs (0x4FF00000-0x5015facd), and causing a boot loop.
The user script load address was increased to 0x50700000, leaving 8MB
of free space for the initramfs, the current initramfs size is 2.37MB.
Use -f, so rm
* does not complain if the file does not exist
* does not exit with 1 if the file does not exist
Remove the stdout/stderr redirect (not needed with -f).
Add exit 0 at the end of the file, even though it clearly should not
exit with anything other than 0 anymore, as it's common practice in
these pre-upgrade etc. scripts.
With the old script, the problem was that it would exit 1 as soon as the
files did not exist at the time the script runs. Exit 1 in this
pre-upgrade script causes apk to show an error, and it would not go away
with 'apk fix' since it ran into the same problem.
Fixes: 7c511d ("pine64-pinephone: remove old u-boot...")
On the pinephone, callaudiod handles the switching of default outputs,
so wys is unnecessary and may be causing issues when running in parallel
with callaudiod.
fixes#1217
with 5.14, there's some change to the path that alsa searches for ucm2
for this device. the install path for PinePhone.conf is changed, and it
references "full" path to HiFi and VoiceCall profiles (which I kept in
`PinePhone` dir, so that there could be several configs for the same
driver later on, if necessary/desired)
`$DEV` was an undefined variable so the atinout commands were printing their
helptext instead of actually running. This was noticeable because
the "Failed to enable VoLTE profile auto selecting" log was being printed
along with said helptext to syslog.
The block that defined `$DEV` had been accidentally deleted in
bb41f53879 . This change restores it.
[ci:ignore-count]
[ci:skip-vercheck] needed for the postmarketos-ui-* packages in this
series
[ci:skip-build] already built ui-* packages in CI, and device pacakges
are just trivial deviceinfo change (manually built some just to verify)
Headset jack events emit 2 events: 'Headset Microphone Jack'
and 'Headphone Jack'. These were properly detected before,
but not headphone jack events only: 'Headphone Jack'.
This change allows to detect headphone jack events as well
and act on these events by setting the headphones as
default audio output while keeping the internal
microphone as audio input. For headsets,
the microphone is switched to the headset microphone as well.
