This device runs on linux-postmarketos-rockchip which at the moment of
writing is 5.13.0 with (only) 6 patches applied, so close-to mainline.
I personally use 2 of these devices with postmarketOS installed daily as
my homeserver setup and it has worked really well. It's also a good
target to run Plasma Bigscreen on as a TV setupbox
Now that CPU scaling is enabled, there is no need to disable the big cluster,
which was hurting performance before by staying at 19.2 MHz. Remove maxcpus=2
from the command line arguments.
[ci:skip-build] Already built successfully on CI
The update to Linux v5.13.1 also includes updating the haptics driver
to the latest one posted to the mailing lists, which was renamed to
qcom-spmi-haptics. Rename the udev rule for this driver and update the
driver name in it.
[ci:skip-build] already built successfully in CI
[ci:ignore-count]
[ci:skip-vercheck] needed for the postmarketos-ui-* packages in this
series
[ci:skip-build] already built ui-* packages in CI, and device pacakges
are just trivial deviceinfo change (manually built some just to verify)
Some msm8916 devices, primarily with two sim slots, require slot
to be selected. Install uim-selection script for all msm8916 devices
with modem enabled.
[ci:skip-build] already built successfully in CI
I sometimes test DB410c via mainline U-Boot, which wants to have the
DTB in the "second" part of the Android boot image. Otherwise it works
fine. Include it there additionally to simplify this.
[ci:skip-build] already built successfully in CI
Having RMTFS at runlevel boot makes it start the modem too fast and causes
crashes. Move it to runlevel default with a post-install.
[ci:skip-build] already built successfully in CI
My engineering prototype 1 Gb pinetab is close to unusable,
so I can't use it to test pmOS. Also, PINE64 is no longer
selling these devices, and the ones that were sent previously
to some developers use different display panel anyway.
Martijn Braam and Dylan Van Assche agreed to maintain it.
[skip ci]
- Add SLPI to nonfree_firmware description
- Add touchscreen and fuel gauge modules to the initramfs in preparation for
osk-sdl and charging-sdl (or any new alternative) support
- Add pointercal file for osk-sdl
[ci:skip-vercheck]
Set package dependency "swclock-offset" to "soc-qcom-msm8916" and
"soc-qcom-sdm845".
These SoC's have a read-only real-time clock (RTC). The package
"swclock-offset" keeps an offset between the RTC and the system time.
Add the missing depends to add the GPU firmware to the initramfs
so that osk-sdl works properly, as well as the haptics driver.
Also make all logs go to UART, this will clean up the splash screen and
let developers with UART access debug the boot process.
[ci:skip-build] This MR was already built on CI
Add the missing depends for our soc package alsa ucm configs. Also add
the missing depends to add the GPU firmware to the initramfs so that
osk-sdl works properly!
Also enable logs and point them to UART, this will clean up the splash
screen and let any developers with UART attached to debug the boot
process.
The PMIC AXP803 sends an interrupt to the A64 CPU when the
battery is critical low. This wakes up the tablet at ~10%
battery level, but UPower wasn't configured to add upon
this interrupt as the action level was way lower.
Therefore, the PMIC performed a hard shutdown when the
battery level dropped further, which may cause data loss.
uboot-tools is provided by u-boot-tools but sometimes apk still gets
confused. This change prevents errors such as
pine64-pinephone:~$ sudo apk upgrade --verbose
WARNING: Failed to perform initial self-upgrade, continuing with full upgrade.
ERROR: unable to select packages:
uboot-tools (virtual):
provided by: u-boot-tools
required by: device-pine64-pinephone-0.25-r1[uboot-tools]
[ci:ignore-count]
[ci:skip-build]: already built in CI successfully
As of MR 2039, the kernel modules are now stripped (INSTALL_MOD_STRIP=1).
It turns out that this massively reduces their size so that including
the panel + touchscreen modules in the initfs still fits into the
partition. This allows the splash screen and osk-sdl to work correctly.
As of MR 2039, the kernel modules are now stripped (INSTALL_MOD_STRIP=1).
It turns out that this massively reduces their size so that including
the panel + touchscreen modules in the initfs still fits into the
partition. This allows the splash screen and osk-sdl to work correctly.
As of MR 2039, the kernel modules are now stripped (INSTALL_MOD_STRIP=1).
It turns out that this massively reduces their size so that including
the panel + touchscreen modules in the initfs still fits into the
partition. This allows the splash screen and osk-sdl to work correctly.
As of MR 2039, the kernel modules are now stripped (INSTALL_MOD_STRIP=1).
It turns out that this massively reduces their size so that including
the panel + touchscreen modules in the initfs still fits into the boot
partition. This allows the splash screen and osk-sdl to work correctly.
Make needed deviceinfo changes to support osk-sdl, add "quiet" to the
cmdline and bump the package version to 1.
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
[ci:skip-vercheck]
Make needed deviceinfo changes to support osk-sdl, add "quiet" to the
cmdline and bump the package version to 1.
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Add a subpackage to ensure that GPU firmware is included in initramfs so
that osk-sdl can work.
[ci:skip-vercheck]
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
