'install' does not properly handle symlinks, it copies the entire file
instead of a symlink to it. This PR uses `cp -a` to preserve symlinks.
For example, with `install`, the files libc.musl-armhf.so.1 and
ld-musl-armhf.so.1 are the same size, despite the fact that in rootfs
libc.musl-armhf.so.1 is actually a symlink to ld-musl-armhf.so.1.
According to @drebrez research, the initramfs size shrunk from
1 567 930 to 1 168 591.
This adds a custom swap file service, which allows specifying a
recommended swap size in the deviceinfo file via
`deviceinfo_swap_size_recommended`. For the N900 this defaults
to 1024 MB now. As the swap file is created in the root partition,
we have encrypted swap now (unless encryption is disabled with
`--no-fde`).
* Check kernel config
* Allow specifying multiple kernel packages, and also no packages
which defaults to scanning all kernel configs (it is super fast
anyway)
* Add the check to Travis CI
* Adjust existing kernel configs, so they pass the kconfig_check.
(We've had to put in a lot of defaults in the aarch64
linux-postmarketos configs, that's why the diff is a bit unclean.)
* Increase modified kernel pkgrels
* Add msm-fb-refresher package and initfs config
* Bump version for pmos-mkinitfs
* Create msm-fb-refresher openrc service
* kill refresher when initfs is done
* weston: upgrade to 3.0.0
* removed no_0hz_refresh_rate patch, as this is upstreamed now
* fix regression in compositor-fbdev
* weston: compile with weston-launch enabled
The following patch is required in order to replace GNU's error()
https://lists.freedesktop.org/archives/wayland-devel/2016-September/031179.html
When modules are surrounded with quotes, modprobe seems to be treating
them as all one module and none of them are actually loaded.
On the N900, where a watchdog module MUST be loaded on boot, this
results in the device shutting down after 30 seconds. This commit
corrects this in init.sh.in
The sdl2 package is forked from upstream Alpine and:
1) adds directfb video support
2) adds a patch to work around a compile issue when directfb is enabled
This commit disables root autologin for postmarketos-base and enabled
root autologin for postmarketos-ui-weston (since weston-launcher is not
built, weston can only be run by root).
* Initial Mozilla Flame packages
* Update dtbtool to use LineageOS upstream
* Use mkbootimg --dt flag only when deviceinfo_bootimg_qcdt is defined
* Update mkbootimg to use LineageOS upstream
* Add sparse image flashing on device-mozilla-flame
* Only support SD card install on Mozilla Flame
* Remove useless profile.sh on mozilla flame
* Package DTBs in /usr/lib/linux-mozilla-flame/
* Build and install modules in linux-mozilla-flame
* Partially resolve#338: Configfs network setup was broken
* Ignore shellcheck warning
...because if we do what shellcheck recommends here, we end up with
exactly the code which we're reverting in this PR.
Thanks to Pablo Castellano and Martijn Braam!
In postmarketOS we are now able to generate system images with the
correct configuration so that they can boot already using qemu
This commit brings the `pmbootstrap qemu` action.
This command is very handy because you don't have to set all the
qemu parameters, pmbootstrap does it for you.
* device-qemu-vexpress: Added kernel command line according to wiki
* qemu: Added workaround for image writing permissions
* qemu: Added support to launch postmarketOS in a QEMU virtual machine
- Support for emulating these architectures in QEMU: arm, aarch64, x86_84
- Generate QEMU command correctly depending no guest architecture (arm/x86)
- Run QEMU in the same architecture as the host by default
- Refactoring in pmb.parse.arch and pmb.qemu.run
- Raise exception if DTB file or system image are not present
- Display more useful information when something fails (e.g. image not found)
- Run qemu version depending on arch (host or argument), not device configured
* device-qemu-amd64: set deviceinfo_kernel_cmdline to "PMOS_NO_OUTPUT_REDIRECT"
* qemu: added --memory argument to specific guest RAM
* device-qemu-amd64: adjusted deviceinfo_kernel_cmdline (console=tty1)
* Added /etc/network/interfaces for qemu-amd64
* qemu: Added KVM support if /dev/kvm if present
* Specify separate machines for architecture
* qemu: Check if QEMU is installed instead of crashing
* Added graphics driver to qemu-aarch64
- Use arm (as used in qemu) instead of armhf (used in Alpine)
- qemu argument is -dtb
- Follow same style to build the command + arguments
* qemu: Added SSH port redirection: ./pmbootstrap.py qemu -p 2222
* Automatically compute the minimum size for the partitions
* Automatically resize the pmOS_root partition during the boot process
* Resize root partition only if there is unallocated space at the end of the device.
* Added more echos to make debugging easier while looking at the pmOS_init.log.
* Updated static_code_analysis.sh script to run shellcheck with `-x` option.
