Package got renamed and "provides" wasn't added, so right now
`apk upgrade -a` with firmware-rtl8723bt installed results in
`ERROR: firmware-pine64-rtl8723bt-0_git20181104-r0: trying to overwrite lib/firmware/rtl_bt/rtl8723bs_config-pine64.bin owned by firmware-rtl8723bt-0_git20181104-r0.`
Add `replaces="firmware-rtl8723bt"` so `apk` prefers this package.
[ci:skip-build]: already built successfully in CI
Instead of encouraging the user to add the directory to
test_directory_structure.py, mention that we just moved the firmware to
device/{main,community,testing}/. This will be more helpful for users
who get the message after rebasing on master.
In the rare case that we need to change the directory structure, we will
figure out which file to edit.
[ci skip]: various firmware packages fail when built at the same time
(they use generic source files like "bcmdhd.cal" with different checksums)
Right now we have all firmware packages under firmware/*.
This is problematic for mainly two reasons:
- It's not immediately clear which firmware packages we need to keep
when forking a new stable branch. (Where we delete testing devices
at the moment...) We might end up deleting firmware packages that
are actually used by one of the devices in community.
- When backporting devices to the stable we cannot just cherry-pick
the commit that moved the device to community (since it does not
contain the firmware package). Instead we need to cherry-pick
earlier commits as well, which may touch a lot of deleted files
in the testing directory.
Let's make this consistent by also placing the firmware packages in
the device/* directory. We already have the common firmware- prefix
to distinguish them from device/kernel packages, which are already
both under the device/* directory.
For most firmware packages we use a vendor- prefix to make it clear
who has provided the firmware. The firmware-rtl8723bt package is only
used for Pine64 devices and actually contains configs that are specific
to Pine64 hardware (e.g. rtl8723bs_config-pine64.bin).
Let's rename it to firmware-pine64-rtl8723bt to make this more clear.
Also cleanup the APKBUILD a bit and provide the LICENSE file in a -doc
subpackage so we can legally redistribute that firmware.
This enables mult-sensor support in sun6i-csi, support for the
gc2145 front camera, the new panel driver from mainline linux
and a small fix for the anx7688 that prevents it spamming the
kernel log when no cable is plugged in on 1.2a hardware.
gitlab.com had a service disruption, so it was not possible to "git
clone" from gitlab.com from some regions, like where the sourcehut
infrastructure is located. Since we are building our packages on
builds.sr.ht, this caused all packages that should be built at that time
to fail. It is working again, so bump the pkgrels to restart the builds.
This switch has happened in the Alpine repos quite a while ago and most
of the pmOS packages were using it already too, so let's switch over the
last ones as well.
This also cleans up the APKBUILDs where necessary
This is the downstream u-boot port for the Galaxy S2.
The load script has been slightly altered to load the kernel from the
KERNEL partition at the 512 KiB offset, instead of loading it from the
RECOVERY partition, since PostmarketOS places the second initramfs in
the RECOVERY partition.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Newer Qualcomm SoCs (e.g. SDM845. MSM8953) seem to use a different
method to talk to the modem. There are no longer separate rpmsg/SMD
channels for QMI messags, instead the modem is also available through QRTR.
On these newer SoCs, installing msm-modem-mainline is pointless,
because the created /dev/modem device will not actually allow
communicating with the modem. However, you still need the part from
the base package (msm-modem), which installs+enables rmtfs.
To avoid confusion, rename the msm-modem-mainline subpackage to
msm-modem-rpmsg. Install only "msm-modem" on SDM845 because that
likely does not allow communication with the modem through RPMSG
anyway.
This upgrades the librem5-base config used to v21:
- better headphone support/detection
- enable runtime PM for usb/SD interface
This also removes the modemmanager subpackage, the udev rule that was
installed by that package is now in modemmanager in Alpine.
This upgrade includes:
1) enabling fb in deviceinfo: This was previously disabled for
debugging purposes, but can be re-enabled now so we get the
awesome postmarketOS splash screen!
2) fixing GPS, kinda: the device has changed, so this fixes the gpsd
config to use the correct device, and includes a udev rule to
make sure the device is owned by a group that gpsd can use
3) usbnet working with configfs
4) disables getty on /dev/ttyGS0, this was usb serial but isn't
configured now that this uses configfs
5) uses Mesa from Alpine, instead of mesa-git in pmaports. Upstream
Mesa has support for the vivante gpu, and no longer need to rely
on mesa master branch for support.
6) fix pulseaudio detection of profiles
7) update the librem5-base version used, includes a udev rule to
configure DDR freq governor as 'powersave' (reduces power, and
how much heat this thing puts out)
fixes#524fixes#526
Put virtual keyboard style into a subpackage, and let the main package
depend on it. That way, it can be used in postmarketos-ondev, without
pulling in all of plasma-phone-components.
