Since audio over DisplayPort (over USB-C) is supported in the kernel,
add a UCM config to complete support.
To be clear, this might not work out of the box yet, I hope it'll start
working better when another audio route (speaker or microphone) is
working from kernel side.
[ci:skip-build]: Already built successfully in CI.
Since the GPU is supported since a while enable
deviceinfo_gpu_accelerated to let pmbootstrap show UIs like phosh.
Also with modem working with patched tqftpserv, we need the
msm-modem-uim-selection dependency, so add that as well.
In mainline Linux these paths will be used, move the firmware packaging
there. By doing this we drop downstream support. Support could be
restored by adding some symlinks in a downstream-specific package if
required.
We also start squashing the firmware into .mbn format with pil-squasher.
For now we keep the files in _wififiles in their old location, I'm not
sure yet where they need to go since I didn't have wcnss working on
mainline yet.
Required for getting mobile data up, otherwise ModemManager fails to
connect with:
Status | connected: no
| connection error name: org.freedesktop.ModemManager1.Error.MobileEquipment.Unknown
| connection error message: failed to create net link for device: failed to add link for device: Could not allocate link: Failed to add link with mux id 1: Netlink message with transaction 27 failed
[ci:skip-build]: already built successfully in CI
Required for getting mobile data up, otherwise ModemManager fails to
connect with:
Status | connected: no
| connection error name: org.freedesktop.ModemManager1.Error.MobileEquipment.Unknown
| connection error message: failed to create net link for device: failed to add link for device: Could not allocate link: Failed to add link with mux id 1: Netlink message with transaction 27 failed
Previously, the modem firmware would be loaded from the modem partition
using this firmware loader. As of the 6.5.4 SDM670 kernel upgrade, the
firmware is installed and loaded from the firmware package. Drop the
dependency on the msm-firmware-loader, which is now unused.
Krane doesn't have a headphone jack, which caused audio server issues
for me. Add a check to only enable the headphone and headset mic device
on non-Krane boards. Also improve the formatting and remove
ChromeOS-specifc options.
[ci:skip-build]: already built successfully in CI
I was building a branch archive previously, which meant that rebuilding
would fail if someone pushed to the branch upstream (the archive
checksum would change)... so I've reverted back to building from a
specific commit for now.
pkgrel was increased because this commit includes a couple of
audio-related patches that weren't included in the previous packaging of
the 6.7 branch.
[ci:skip-build] Already build-tested on Gitlab CI
Similarly to how it was done for xiaomi-beyllium with varying
display panels, add kernel variant for clover-plus.
Mi Pad 4 Plus is very very similar to regular Mi Pad 4,
but it has different panel and different touchscreen.
Therefore it uses different device tree in kernel - and it
is the only changed line in deviceinfo file.
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
[ci:skip-build]: Already built successfully in CI.
In order to make it work properly, the fcc unlock script from MM should
also be enabled... This info will be added to the device's wiki page for
now since upstream MM discourages distros from enabling these unlock
scripts by default...
fixes https://gitlab.com/postmarketOS/pmaports/-/issues/2489
[ci:skip-build]: Already built successfully in CI.
The fbdev backend was removed with Weston 10 which has been out for a
good while now. As such, it doesn't matter whether Xwayland works or not
since Weston won't work at all --- the DRM backend, which is what would
get used instead of fbdev with this removed, won't work on downstream
kernels like the one used by this device.
[ci:ignore-count]
[ci:skip-build]: Already built successfully in CI.
The fbdev backend was removed with Weston 10 which has been out for a
good while now. As such, it doesn't matter whether Xwayland works or not
since Weston won't work at all --- the DRM backend, which is what would
get used instead of fbdev with this removed, won't work on downstream
kernels like the one used by this device.
There is no dri-backend.so. I don't know if this ever existed. May have
been a typo where the author meant to type drm-backend.so. The DRM
backend should be the default anyway, so just remove it instead of
fixing what may have been a typo.
The fbdev backend was removed with Weston 10 which has been out for a
good while now. This device should be able to use the DRM backend
anyway given that it uses the A64 SoC which also e.g. the PinePhone
uses.
Additionally, the comment about Xwayland being broken contradicts the
actual configuration file where Xwayland actually is being enabled
(xwayland=true), so this shouldn't be causing any regressions even if it
actually is broken.
The fbdev backend was removed with Weston 10 which has been out for a
good while now. As such, Weston won't work with the downstream port
anyway which is likely where Xwayland supposedly was broken. As such,
remove this unnecessary configuration file.
We did set these variables, so it is possible to flash boot and root
partitions separately for booting with stock partition table. This
is useful for U-Boot as secondary bootloader. But it's not good for
U-Boot as primary bootloader because the resulting images have boot
and root partitions separated, so users have to create partitions
themselves and this is very confusing.
I'm suggesting to disable it in favor of doing U-Boot as primary
bootloader, this may be harder for users, but it needs to be done
only once, and this way is more fancy and is supported on more
devices than secondary bootloader.
If someone still wants to use this port with U-Boot as secondary
bootloader they can do "pmbootstrap install --split" and
"pmbootstrap export" to get 2 separate partitions to flash.
[ci:skip-build]: Already built successfully in CI.
bcm4330 has 2 wifi sdio firmwares, one with IEEE 802.11а support
and one without. One without was missing which caused some
devices to have wireless network issues.
Additionally Oyua specific bluetooth firmware was found and it
is included as well.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
[ci:skip-build]: Already built successfully in CI.
Fixes#2349. Patches refreshed because some didn't apply when I built
directly from local repo and tried to import them with "git am".
Known issue: NetworkManager fails to assign IP to usb0, I had to
assign it manually to use USB networking.
In the mainline ds2482 onewire kernel driver, active_pullup defaults to
1 which is setting the APU register. This caused the connection to the
ds2784_battery slave to be unstable and flaky. In the AOSP manta project
this flag is set to 0 as well.
This is a device-specific package. The only device that depends on
this, device-nokia-n900, is in community, so let's move it there too.
[ci:skip-build]: already built successfully in CI
This is a device-specific package. No need to keep it in main where it
gets included in stable releases unnecessarily. The only device that
depends on this, device-inet-a33, is in testing, so let's move it there
too.
Also start squashing the .mdt files into .mbn and provide compatibility
symlinks so old kernels that look for .mdt still find it.
Also move the zap firmware into a device-specific subdirectory.
Symlinks for venus are skipped since that one's not used in any
production branch yet for sm7225.
[ci:skip-build]: Already built successfully in CI.
These cmdline params are not needed because the issues they worked
around were fixed in 6.7 or in this kernel branch we are using.
Additional modules are included in the initramfs since they may not be
builtin in the future, and not having them loaded in the initfs can break booting
kconfig changes:
- Most are due to running 'pmb kconfig migrate'
- Enable USB_F_FS
- Build ath11k as a module + enable debug, to help with debugging
pma#2361
- Enable support for BT BR/EDR stuff (like HFP)
- Enable CRYPTO_MD4 for EAP_MSCHAPv2
This uses oem-specific packages for configuring Intel and AMD systems,
and installs them all by default for new images using pmbootstrap's
pmb_recommends feature.
The intention is to provide pre-built images with support for Intel and
AMD already enabled/configured, and users can remove an unwanted set of
packages (e.g., `apk del device-generic-x86_64-intel` when on an AMD
system) if they want to.
Upgrading existing systems should work, in that I haven't observed any
apk conflicts with it. But you do need to manually install the new
oem-specific package if you need it (e.g. `oem-intel`)
fixes https://gitlab.com/postmarketOS/pmaports/-/issues/2484
The panel driver has been renmaed in the kernel sources to be in line
with what's going to be upstreamed.
[ci:skip-build]: Already built successfully in CI.
In preparation of new sdm660-mainline kernel release all
downstream ports will become irrelevant.
If needed, downstream port can still be chosen as
'xiaomi-lavender-downstream' during pmbootstrap init.
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
[ci:skip-build]: already built successfully in CI
non-free firmware not (yet?) submitted to linux-firmware, this is pulled
directly from the latest versions distributed by lenovo, instead of some
probably outdated repo distributed by random folks.
The bt firmware here fixes an issue where the bt range on the 21bx is
extremely poor (like ~1 meter or less)
linux3.4-ARM-8933-1-replace-Sun-Solaris-style-flag-on-section-xz-supplementation.patch
contains an addition that was not part of
linux3.4-ARM-8933-1-replace-Sun-Solaris-style-flag-on-section.patch
simply because error did not occur with the config I tested with.
[ci:skip-build]: already built successfully in CI
