gzip results in a boot.img that's too big (over 8 MB) for e.g.
samsung-i9300, so let's replace it with something that produces
smaller kernels. With this, the entire boot.img is 6,3 MB (down
from 8MiB, or 8.5458944 MB) which leaves plenty of space on the
8 MB partition and prevents the recovery from being overwritten
when this kernel is flashed.
Tested and works on samsung-i9300.
[ci:skip-build] already built successfully in CI
This provides a mobile-friendly music player in the default
installation which is something that's currently lacking.
[ci:skip-vercheck]: _pmb_recommends change doesn't need pkgrel bump
The networkmanager hotspot needs to have DHCP input enabled on the wifi
interfaces so the temporary dnsmasq instance can work. The
networkmanager backend is also switched to the nftables one so it can
create the ad-hoc hotspot forwarding/masquerade table.
Proper fix for the monospace fonts seen when postmarketos-ondev is
installed without also installing osk-sdl. This doesn't happen anymore
with pmbootstrap install --ondev, because it will always pull in osk-sdl
again for other reasons. However, since postmarketos-ondev is using this
font, let's directly depend on it instead of having it pulled in as side
effect of also having osk-sdl installed.
And extend bootloader CMDLINE per default, giving us the option to
change the CMDLINE both via the kernel config and from samsung's
S-BOOT shell.
Note: the default console in exynos_defconfig (which this config is
based on) is ttySAC1, but all midas devices uses ttySAC2, so set it to
ttySAC2 instead. Also remove all other variables. They are not needed,
and (at least) root=/dev/ram0 seem to prevent us from booting pmos.
[ci:skip-build] already built successfully in CI
When kernel variants were renamed in
69cd6ff843
these dtb vars were forgotten, making it impossible to boot a kernel
build with `pmbootstrap build linux-postmarketos-exynos4`, no dtb is
appended to the zImage and we get stuck on samsungs boot logo.
uim-selection has "after *" in it's dependencies to make sure the
theoretical up to ~1min delay can't be observed. Unfortunaely this
causes incorrect dependencies ordering if one of other services depends
on ofono or modemmanager. Drop "after *" so modem can always be started
properly.
NymphCast is a FOSS Chromecast replacement (not a drop-in one though)
and allows you to "cast" audio and video to your device running the
nymphcast server. Plasma Bigscreen seems like an ideal use-case for this
so let's install and launch it by default. People can always uninstall
it anyways
Merged in mainline since 5.9-rc2-next-grate:
- all previously applied patches specific for Tegra and Nexus 7
New features, not merged yet in mainline (only in -next-grate):
- improved power management
- implemented USB OTG
New configuration options
- enable F2FS support (incl. compression), which leads to prolonging
eMMC life
Tested on E1565.
Signed-off-by: David Heidelberg <david@ixit.cz>
This allows using lm_sensors to read temperature data on the pinebook
pro (and probably other devices too)
❯ sensors
gpu_thermal-virtual-0
Adapter: Virtual device
temp1: +41.1°C (crit = +95.0°C)
tcpm_source_psy_4_0022-i2c-4-22
Adapter: rk3x-i2c
in0: 5.00 V (min = +5.00 V, max = +5.00 V)
curr1: 2.50 A (max = +2.50 A)
cw2015_battery-i2c-4-62
Adapter: rk3x-i2c
in0: 4.24 V
curr1: 0.00 A
cpu_thermal-virtual-0
Adapter: Virtual device
temp1: +47.5°C (crit = +95.0°C)
nvme-pci-0100
Adapter: PCI adapter
Composite: +31.9°C (low = -273.1°C, high = +80.8°C)
(crit = +80.8°C)
Sensor 1: +31.9°C (low = -273.1°C, high = +65261.8°C)
Sensor 2: +37.9°C (low = -273.1°C, high = +65261.8°C)
[ci:skip-build] Already built on CI
5.13.5 had some rockchip-related fixes in the changelog, so I figured
why not upgrade to it.
These patches from Manjaro seem to be the bare minimum required to get
usb-c charging and device peripherial support working again (external
display still doesn't work)
[ci:skip-build] already built successfully in CI
There's a generic udev rule to set group ownership of backlights to
'video', but it only runs on the ADD action, which seems to be too
late(?) since the backlight device is never owned by 'video' on boot.
This rule will run on CHANGE too, which might be overkill but seems to
get the job done. It's now possible to set the backlight brightness on
the PBP as a normal user.
llvm was left over from Martijn's efforts to reduce the kernel size
The drivers for external DP are enabled here, but all patches from
manjaro that deal with DP/typec alt mode, etc are dropped since they do
not solve anything on their own and may cause display instability
issues...
[ci:skip-build]: already built successfully in CI
