Improvements from xfce4-phone source:
- Add screenshot to README.md
- Enable screen locking
- Disable Desktop icons "Home", "File System", "Trash"
- Enable single-click on Desktop
- Enable single-click in Thunar
- Change clock format
- Set postmarketos wallpaper
Additional changes in postmarketos-ui-xfce4:
- Installing greybird-themes (which is already set as default theme in
/etc/xdg/xfce4/xfconf/xfce-perchannel-xml/xsettings.xml).
- Changing /etc/skel/.config/autostart/onboard-autostart.desktop to
slightly speed up keysboard startup (overriding startup-delay of
/etc/xdg/autostart/onboard-autostart.desktop).
- Enabling scrollbars by /etc/profile.d/enable-scrollbars.sh, this is
helpful where touch-scrolling doesn't work like e.g. in whiskermenu.
(And re-ordered network-manager-applet in APKBUILD _pmb_recommends
section.)
Also removing xfce4 subpackages of device-qemu-amd64,
device-qemu-aarch64 and device-nokia-n900. The device specific monitor
to set the wallpaper will now be automatically derived from "monitor0"
in file xfce4-desktop.xml.
Additionally taking maintainership as discussed in merge request
(!2506).
Add pmb:cross-native/!tracedeps to applicable firmware packages and
secure both with a test.
This sets the pmb:cross-native and !tracedeps options on all firmware-*
packages that are compatible with the native compilation method. A unit
test ensures the presence of both options while maintaining a list of
exempted packages.
Fixes: #718
[ci:ignore-count] [ci:skip-vercheck] [ci:skip-build]
Use -f, so rm
* does not complain if the file does not exist
* does not exit with 1 if the file does not exist
Remove the stdout/stderr redirect (not needed with -f).
Add exit 0 at the end of the file, even though it clearly should not
exit with anything other than 0 anymore, as it's common practice in
these pre-upgrade etc. scripts.
With the old script, the problem was that it would exit 1 as soon as the
files did not exist at the time the script runs. Exit 1 in this
pre-upgrade script causes apk to show an error, and it would not go away
with 'apk fix' since it ran into the same problem.
Fixes: 7c511d ("pine64-pinephone: remove old u-boot...")
On the pinephone, callaudiod handles the switching of default outputs,
so wys is unnecessary and may be causing issues when running in parallel
with callaudiod.
fixes#1217
with 5.14, there's some change to the path that alsa searches for ucm2
for this device. the install path for PinePhone.conf is changed, and it
references "full" path to HiFi and VoiceCall profiles (which I kept in
`PinePhone` dir, so that there could be several configs for the same
driver later on, if necessary/desired)
The Alpine LTS kernel builds evdev as a module which means it's not automatically
available in the initfs. Including evdev allows osk-sdl to properly recognise
physical keyboards, just like on a real device.
Fixes: #1204
[ci:skip-build] already built successfully in CI
`$DEV` was an undefined variable so the atinout commands were printing their
helptext instead of actually running. This was noticeable because
the "Failed to enable VoLTE profile auto selecting" log was being printed
along with said helptext to syslog.
The block that defined `$DEV` had been accidentally deleted in
bb41f53879 . This change restores it.
[ci:ignore-count]
[ci:skip-vercheck] needed for the postmarketos-ui-* packages in this
series
[ci:skip-build] already built ui-* packages in CI, and device pacakges
are just trivial deviceinfo change (manually built some just to verify)
Workaround for https://source.puri.sm/Librem5/linux-next/-/issues/303.
It seems worth sacrificing some power savings for a modem that won't
disappear, at least until the above issue is fixed.
[ci:skip-build]: already built successfully in CI
Headset jack events emit 2 events: 'Headset Microphone Jack'
and 'Headphone Jack'. These were properly detected before,
but not headphone jack events only: 'Headphone Jack'.
This change allows to detect headphone jack events as well
and act on these events by setting the headphones as
default audio output while keeping the internal
microphone as audio input. For headsets,
the microphone is switched to the headset microphone as well.
The PMIC AXP803 sends an interrupt to the A64 CPU when the
battery is critical low. This wakes up the phone at ~10%
battery level, but UPower wasn't configured to add upon
this interrupt as the action level was way lower.
Therefore, the PMIC performed a hard shutdown when the
battery level dropped further, which may cause data loss.
We used to have it at 40% and just bumped it to 100%. With 100%, I can
hear static noise in the headphones when using the PinePhone (pmOS CE)
in a silent room, even if I turn the volume down in Pulseaudio (e.g.
18%-30% in Phosh). This was not the case when we had it at 40%.
70% seems to be the sweet spot, where no static noise can be heard when
using headphones in a silent room, but where volume can still be turned
up to a very high level if necessary.
Upstream changelog:
ca736e844a
Patches rebased, and includes some new fixes:
arm64-dts-imx8mq-librem5.dtsi-adjust-the-usdhc-bus-s.patch
- Being tested by Purism as well, has shown some promise improving GPS
reliability
arm64-dts-imx8mq-disable-SuperSpeed-instances-in-par.patch
- Fixes issue with modem disappearing
Upstream changelog:
4e76143d2e
Note, previous wifi driver behavior is not changed. The redpine module
still expects the fw to be in /lib/firmware on boot, and won't use the
fw on the card.. Theoretically this kernel version now supports both
loading fw from rootfs into ram AND using fw burned on the chip, but
since I haven't tested that well yet I'm leaving this as-is.
[ci:skip-build]: already built successfully in CI
uboot-tools is provided by u-boot-tools but sometimes apk still gets
confused. This change prevents errors such as
pine64-pinephone:~$ sudo apk upgrade --verbose
WARNING: Failed to perform initial self-upgrade, continuing with full upgrade.
ERROR: unable to select packages:
uboot-tools (virtual):
provided by: u-boot-tools
required by: device-pine64-pinephone-0.25-r1[uboot-tools]
[ci:ignore-count]
[ci:skip-build]: already built in CI successfully
mce is used by both Glacier and Asteroid to do all kind of power
management related stuff, including blanking the display. However,
obviously we don't ever want to blank the display on Qemu
Upstream changelog:
6dcba4b588
The redpine interrupt handler patch has been dropped since it's now
merged in Purism's tree.
[ci:skip-build]: already built successfully in CI
