* firmware-asus-flo: packaged all flo firmware
* device-asus-flo: depend on firmware-asus-flo package
* default android wifi config
* Add wifi and freedreno support
* change to console=ttyMSM0 - as per https://dflund.se/~triad/krad/nexus7-flo/
* Add current kernel config as it is currently working with wifi.
* Increase pkgrel to account for changes in the kernel config.
Quite a few things use dbus (plasma, hildon, ofono, connman,
networkmanager, etc) that I think it makes sense to just have this
started by default in pmOS rather than have every device package
implement this on their own.
In case someone shows up with a use-case, where dbus by default
is not desired, please speak up. Possible solutions are in #628.
* Started with stock kernel config (fairphone-perf_defconfig)
* Enabled DEVTMPFS
* Deactivated MSM_KGSL
* Enabled the serial console
* Enabled USB networking
'install' does not properly handle symlinks, it copies the entire file
instead of a symlink to it. This PR uses `cp -a` to preserve symlinks.
For example, with `install`, the files libc.musl-armhf.so.1 and
ld-musl-armhf.so.1 are the same size, despite the fact that in rootfs
libc.musl-armhf.so.1 is actually a symlink to ld-musl-armhf.so.1.
According to @drebrez research, the initramfs size shrunk from
1 567 930 to 1 168 591.
This adds a custom swap file service, which allows specifying a
recommended swap size in the deviceinfo file via
`deviceinfo_swap_size_recommended`. For the N900 this defaults
to 1024 MB now. As the swap file is created in the root partition,
we have encrypted swap now (unless encryption is disabled with
`--no-fde`).
This is a workaround for #429, until the iteration count can be
specified directly in cryptsetup.
* Add default iter-time option, and option to override
* set SHA1 default hash for luksFormat, add option to override
* [RX51] load omap-sham in initramfs for HW accel. sha1
* Add LG G Watch (dory) support
* Use github.com mirror instead of googlesource.com to have fixed checksum
* Fix kernel compilation and remove unnecessary initfs-hook for framebuffer settings
* Check kernel config
* Allow specifying multiple kernel packages, and also no packages
which defaults to scanning all kernel configs (it is super fast
anyway)
* Add the check to Travis CI
* Adjust existing kernel configs, so they pass the kconfig_check.
(We've had to put in a lot of defaults in the aarch64
linux-postmarketos configs, that's why the diff is a bit unclean.)
* Increase modified kernel pkgrels
* Add msm-fb-refresher package and initfs config
* Bump version for pmos-mkinitfs
* Create msm-fb-refresher openrc service
* kill refresher when initfs is done
- Revert to LineageOS 14.1 kernel
- Enable virtual terminal
- Update touchscreen settings
At the moment, display output works, but only when the following is run:
while [ ! ]; do cat /sys/class/graphics/fb0/modes >
/sys/class/graphics/fb0/mode; done.
Adding INSTALL_MOD_STRIP will cause modules to be stripped after
they are installed (option --strip-debug will be used)
In case someone isn't happy with it, please open a PR that reverts
it for your device, or start a discussion as a new issue.
* weston: upgrade to 3.0.0
* removed no_0hz_refresh_rate patch, as this is upstreamed now
* fix regression in compositor-fbdev
* weston: compile with weston-launch enabled
The following patch is required in order to replace GNU's error()
https://lists.freedesktop.org/archives/wayland-devel/2016-September/031179.html
