Make use of stock depthcharge bootloader to not deal with U-Boot issues:
- broken USB
- broken eMMC
- broken latest version of U-Boot
Use extlinux instead of Grub for users with U-Boot to simplify process.
Also, some of old U-Boot builds may not support EFI.
[ci:skip-build] already built successfully in CI
Make use of stock depthcharge bootloader to not deal with U-Boot issues:
- broken USB
- broken eMMC
- broken latest version of U-Boot
Use extlinux instead of Grub for users with U-Boot to simplify process.
Also, some of old U-Boot builds may not support EFI.
[ci:skip-build] already built successfully in CI
New features:
* msm8994-huawei-angler: Add sdhc1 definition (internal SD card).
Backporting 3 patches:
* 0001-arm64-dts-msm8992-bullhead-add-memory-hole-region.patch
fixes bullhead boot since 6.0-rc1, already in qcom tree
* 0002-arm64-dts-qcom-msm8992-bullhead-Fix-cont_splash_mem-.patch
memory fix, likely to be merged
* 0003-arm64-dts-qcom-msm8992-bullhead-Disable-dfps_data_me.patch
memory fix, likely to be merged
* 0004-arm64-dts-qcom-msm8992-Don-t-use-sfpb-mutex.patch
memory fix, likely to be merged
* 0005-arm64-dts-msm8994-angler-fix-the-memory-map.patch
fixes angler reset during starting services in rootfs,
likely to be merged
Remove all backported commits from newer versions.
While at it, remove various CONFIG_NET_VENDOR_.* and
CONFIG_MSM_.* and CONFIG_.*_QCOM_.* for other SOCs.
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
[ci:skip-build]: already built successfully in CI
Shared SoC package for MSM8909
Currently provides a dummy soc-qcom-msm8909 package that depends on
soc-qcom-msm8916 and a soc-qcom-msm8909-modem package for modem support.
Since the RTC like on most Qualcomm chips is read-only, use
swclock-offset package to fix up time after boot.
And since we don't need msm-fb-refresher on mainline, move it to the
downstream kernel subpackage.
Basic support for the Kobo Libra H2O ebook reader.
Waveform handling shares the same oddities as for the Kobo Clara HD, the
existing waveform from eMMC is used.
Preferred way to install is to export the eMMC as USB Mass storage,
backing it up, and installing there.
U-Boot is a more recent one than the factory u-boot, supporting easy
access for buttons/LEDs. Pressing PageUp while powering on gives you the
possibility to enable USB mass storage mode to restore your backup.
Kernel is the near mainline kernel also used by the Kobo Clara HD.
It lacks some devicetree additions which are planned for the next
update, but basic things like buttons, usb, serial and wifi are
supported.
The WCNSS firwmare used for motorola-harpia seems to have weird issues
that prevent using WiFi properly except for a few limited channels. It
is not clear why this happens, it seems to be some peculiar firmware
difference (perhaps the channels need to be enabled with some
non-standard command).
Since Motorola uses the same signing keys for all their MSM8916
devices, it is possible to use the firmware from other devices instead.
Initial testing shows promising results when using the older WCNSS
firmware from motorola-osprey instead, it does not seem to have this
issue.
It's not clear yet if this has any negative effects. The WCNSS firmware
should not be device-specific, but theoretically it could be (if
Motorola made some weird changes inside it).
For now just package it in firmware-motorola-osprey-wcnss. This package
can be easily installed on harpia devices for testing (using apk add)
and will then take precendence over the default firmware from the
firmware partition (via msm-firmware-loader).
Move firmware-motorola-osprey from testing to community so that the
package is preserved for motorola-harpia users (testing is deleted in
stable branches).
[ci:skip-build]: already built successfully in CI
motorola-osprey can generally use the firmware from motorola-harpia
(which is a bit newer). However, the WCNSS_qcom_wlan_nv.bin is usually
device specific (it contains some kind of calibration values for
WiFi/BT).
The file packaged in firmware-motorola-osprey-wcnss-nv is identical to
the file in firmware-motorola-harpia-wcnss-nv. However, It looks a bit
like this might be a mistake in the source repository
(https://github.com/pmsourcedump/firmware-motorola-osprey). The
wlan/prima folder there is completely identical to the one used for
motorola-harpia, but the stock ROM and LineageOS use different files.
Fix this by packaging the file from TheMuppets. Also modernize the
firmware-motorola-osprey package by applying pil-squasher to the
venus/video firmware.
motorola-osprey has a very clunky name at the moment "Motorola Moto G
3rd gen. (2015)". The device was mostly just called "Motorola Moto G"
by Motorola, so it is hard to choose a fitting (but unique) name.
In the postmarketOS wiki it is called "Motorola Moto G 2015" so let's
just drop the "3rd gen." in the pmOS device package as well.
Also make the deviceinfo consistent with harpia while at it.
This adds initial support to CutiePi tablet, with basic peripherals, sound, touchscreen, and wireless support.
Signed-off-by: Raffaele Tranquillini <raffaele.tranquillini@gmail.com>
Add peripheral overlays
Signed-off-by: Raffaele Tranquillini <raffaele.tranquillini@gmail.com>
[ci:skip-build]: Already built successfully in CI
