This fixes gnss out of the box on the librem 5, by configuring geoclue
to use gnss-share as a nmea source.
I went this route, of overriding a .service file that invokes geoclue
with a command line option, because forking this .service file is much
nicer than forking geoclue.conf. The conf file will likely change over
time to add new app permissions or whatever, and it's unlikely
(hopefull!) that this .service file will change much upstream...
[ci:skip-build] already built successfully in CI
CONFIG_USB_GADGET=y
CONFIG_USB_DWC3_DUAL_ROLE=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_PLATFORM=y
CONFIG_USB_DWC2=y
remove un-necessary activated configs
[ci:skip-build]: already built successfully in CI
Add rules for regulator-haptic, which is used on:
- samsung-e5/e7
- samsung-cprime/gprime
- samsung-j3/j5(x)
Note that regulator-haptic is not supported on some devices yet,
and samsung-e5 is not ported at the moment.
[ci:skip-build]: already built successfully in CI
- Also enabled LRU_GEN by default like on the PinePhone OG
- Set Ext4 module to built-in as this currently is the main fs used for PPP.
Contains the following patch:
- pinephone pro: finished fix for LCD to make it refresh at precisely 60 Hz
[ci:skip-build]: already built successfully in CI
Add new patches:
- enable serial console
- save relocation address to find KASLR
- buttons as keyboard input driver to navigate bootmenu
- bootmenu loop entry selection
Apparently upstream names udev rules with the .udev extension... which
doesn't work with udev (I guess debian has a helper for installing rules
and it renames them?). This adds the expected ".rules" extension to them
so that udev actually uses them.
This update also includes improved ucm config from Purism.
"Lockdown suppport" is also added here, which allows toggling off all of
the hks on the L5 to disable all radios, etc without breaking some
sensors. For more info, see 65ec7038 in librem5-base.
Based on some new (to me...) info from Purism's Sebastian K, there are
apparently Evergreen devices that return different values for board rev,
so we shouldn't assume only r4 are Evergreen, and default to the r2 DT.
But many earlier devices (Birch, Chestnut, Dogwood) may or may not have
the board rev set either. Who knows! Defaulting to the Evergreen DT on
these devices is bad too, but there weren't many of those shipped (I
guess?), at least not compared to the number of Evergreens that aren't
properly identifiable in u-boot... so this using this DT by default is
the best of the two bad options we have.
This comment thread has more info:
https://gitlab.com/postmarketOS/pmaports/-/issues/1643#note_1147248594fixes#1643
[ci:skip-build] already built successfully in CI
Add the CONFIG_DW9714 symbol to the PinephonePro defconfig.
The PinephonePro rear camera module uses the DW9714 VCM to drive the
lens, and a driver is required to successfully complete the media
graph probe sequence.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Kernel source updated to 6.1-rc7
Ext2 and Ext3 modules in aarch64 config disabled because Ext4 is backwards compatible.
2 fixes for PinePhone included in this source:
pinephone: fix power key behavior during suspend (avoid stuck key during resume)
pinephone keyboard: wait for 100ms after enabling power supply and before probing.
[ci:skip-build]: already built successfully in CI
In SDM845, the q6voice kernel driver connects modem and audio backends.
Callaudiod seems to switch to correct audio device and prepares it, however, the audio
device get's closed since no one from the userspace is actively listening to it.
This cuts the audio in call. As a workaround, I have added to script to disable the
suspend-on-idle pulseaudio module during calls, so the audio devices don't close automatically.
Includes the following changes:
- rebase onto rc4
- squash a few changes which were marked to get squashed/fixups
- dropped "wcd934x: use .prepare and .shutdown instead of .trigger"
- OP6 audio device tree changes
- revert of a DSI DCS commit[1], which caused havoc in unprepare
hooks of panel drivers
[1] - https://lore.kernel.org/linux-arm-msm/1892d0af-8aa4-dc03-887a-e44bb623b836@linaro.org/
Change-Id: I4790a278c0d35618ca824a036982769e66767ffd
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
It should have depended on mutter-mobile-schemas instead of
mutter-mobile. Looks like mutter-mobile-schemas was getting installed
instead of mutter-mobile for it only by chance until now.
[ci:skip-build]: already built successfully in CI
Downstream for kernel development, not for actual use.
Kernel defconfig taken from stock with:
- CONFIG_ANDROID_PARANOID_NETWORK unset
- CONFIG_DEVTMPFS set
- CONFIG_EXT4_FS_POSIX_ACL set
- CONFIG_LOCALVERSION set to "-downstream"
- CONFIG_SYSVIPC set
- CONFIG_USB_CONFIGFS_RNDIS set
- CONFIG_USER_NS set
Change-Id: I22bfd30dfc664dfaa2123c856b3662ddb37e760f
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
[ci:skip-build]: already built successfully in CI
The variable describes the configfs function name to use, no matter if
it's rndis, ncm, ecm or any other function. So change the name of the
variable, the string we write to the configuration file and some
comments.
