- Add support for Samsung Galaxy Note 3 (hlte)
- Changes to kernel config:
- add support for anbox
- add support for nftables
- add support for lxc, docker
- add support for Wireguard
- Disable CONFIG_ARM_APPENDED_DTB (for lk2nd compatibility)
[ci:skip-build] Already built on CI in a MR
Don't suspend the device while alsa is playing. I ran this for two days
in combination with suspend time set to 1 min on the pinephone and it
works great. Finally no suspend while VLC is playing podcasts.
Add the missing depends to add the GPU firmware to the initramfs
so that osk-sdl works properly, as well as the haptics driver.
Also make all logs go to UART, this will clean up the splash screen and
let developers with UART access debug the boot process.
[ci:skip-build] This MR was already built on CI
Add the missing depends for our soc package alsa ucm configs. Also add
the missing depends to add the GPU firmware to the initramfs so that
osk-sdl works properly!
Also enable logs and point them to UART, this will clean up the splash
screen and let any developers with UART attached to debug the boot
process.
This updates to the Linux stable 5.12.8 release, it also adds the kernel
side support for the speaker and headphone jack on the OnePlus 6 (
unfortunately not the 6T)
AsteroidOS uses this config file to determine how the UI should look
(e.g. a round or a square screen), and if some things like Wi-Fi are
supported. Upstream auto generates this config file, but it seems so
simple and small that I think it's better for us to just ship the file
next to the APKBUILD
AsteroidOS uses this config file to determine how the UI should look
(e.g. a round or a square screen), and if some things like Wi-Fi are
supported. Upstream auto generates this config file, but it seems so
simple and small that I think it's better for us to just ship the file
next to the APKBUILD
The PMIC AXP803 sends an interrupt to the A64 CPU when the
battery is critical low. This wakes up the tablet at ~10%
battery level, but UPower wasn't configured to add upon
this interrupt as the action level was way lower.
Therefore, the PMIC performed a hard shutdown when the
battery level dropped further, which may cause data loss.
The PMIC AXP803 sends an interrupt to the A64 CPU when the
battery is critical low. This wakes up the phone at ~10%
battery level, but UPower wasn't configured to add upon
this interrupt as the action level was way lower.
Therefore, the PMIC performed a hard shutdown when the
battery level dropped further, which may cause data loss.
TF201 nvram was updated since previous did not work on some devices.
Added support for TF101, TF300TG and TF300TL.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
On my librem 5 when using directfb in initfs, touch input is really
inconsistent... the cursor seems to jump around and it's hard to enter
keys in osk-sdl. This is completely 'fixed' by disabling the ps2mouse
input module in dfb.
I guess this might cause mice to stop working (?), but I can't think of
any situation where someone would run osk-sdl in initfs on a device that
has a ps2 mouse but no keyboard (which would make more sense to use for
entry than the mouse..)
Next release of ModemManager needs Qualcomm RMNET support
for QMAP mobile data support.
armv7 config doesn't have ethernet enabled at all,
so this is only enabled for the aarch64 config.
I rebased all of the patches (only 2 needed some changes, the rest I
just did for good measure).
These two patches were dropped since they are already merged in the new
kernel:
0008-leds-gpio-Set-max-brightness-to-1.patch
0009-dts-pinephone-Add-pine64-pinephone-to-compat-list.patch was dropped
The kconfig changes are just after running kconfig edit, and making no
changes so that it would generate a config with any new options in 5.12,
to make maintenance easier moving forward.
* Prevent interactive warning to pop once already approved when
[over/down]clocking DRAM
* Make sure $freq is always set
Co-Authored-By: Oliver Smith <ollieparanoid@postmarketos.org>
In 35f283a8ef sxmo was made to install
sxmo on clean installs, but due to
9387842aec was getting uninstalled if it
was installed before. Let's properly depend on it instead so people
don't end up without working networking
Gummiboot was dropped from Alpine. Switch to grub, which is what we use
for tablet-x86uefi too.
In contrary to tablet-x86uefi, run the grub-mkimage command directly
inside the device package:
* This avoids creating another confusing grub-x86 like package (looks
like the x86 version of alpine's grub package, as it's the case with
grub-efi-x86, but actually it is just the result of grub-mkimage).
* In contrary to grub-efi-x86, the resulting efi file is not shared
across several devices.
* It's consistent with uboot mkimage commands, which we also run in
device packages.
Related: 398b7aef0b
