pmaports/device/testing/linux-clockworkpi-uconsole-cm4/0004-arm-dts-overlays-add-uconsole-cm4.patch

Original patch: https://github.com/PotatoMania/uconsole-cm3/blob/dev/PKGBUILDs/linux-uconsole-cm3-rpi64/0004-arm-dts-overlays-add-uconsole.patch
Adapted from Raspberry Pi CM3 to Raspberry Pi CM4

diff --git a/arch/arm/boot/dts/overlays/Makefile b/arch/arm/boot/dts/overlays/Makefile
index 04a9c9a8ab90..ddd90f3f087d 100644
--- a/arch/arm/boot/dts/overlays/Makefile
+++ b/arch/arm/boot/dts/overlays/Makefile
@@ -284,6 +284,7 @@ dtbo-$(CONFIG_ARCH_BCM2835) += \
 	uart4.dtbo \
 	uart4-pi5.dtbo \
 	uart5.dtbo \
+	uconsole.dtbo \
 	udrc.dtbo \
 	ugreen-dabboard.dtbo \
 	upstream.dtbo \
diff --git a/arch/arm/boot/dts/overlays/uconsole.dts b/arch/arm/boot/dts/overlays/uconsole.dts
new file mode 100644
index 000000000000..bfc12f7a029b
--- /dev/null
+++ b/arch/arm/boot/dts/overlays/uconsole.dts
@@ -0,0 +1,233 @@
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+/* uConsole All In One */
+
+/ {
+	compatible = "brcm,bcm2835";
+
+	fragment@70 {
+		target-path = "/aliases";
+		__overlay__ {
+			i2c_uconsole = "/i2c@0";
+		};
+	};
+
+	fragment@71 {
+		target-path = "/__symbols__";
+		__overlay__ {
+			i2c_uconsole = "/i2c@0";
+		};
+	};
+
+	fragment@80 {
+		target-path = "/chosen";
+		__overlay__ {
+			bootargs = "snd_bcm2835.enable_headphones=1";
+		};
+	};
+
+	fragment@90 {
+        target-path = "/";
+		__overlay__ {
+			audio_amplifier: audio-amplifier {
+				compatible = "simple-amplifier-switch";
+				sw-gpios = <&gpio 10 1>; /* GPIO10, GPIO_ACTIVE_LOW */
+				outputs-gpios = <&gpio 11 0>; /* GPIO11, GPIO_ACTIVE_HIGH */
+				// vdd-supply = <&uc_reg_5v0>;
+			};
+
+			ocp8178_backlight: backlight@0 {
+				compatible = "ocp8178-backlight";
+				backlight-control-gpios = <&gpio 9 0>; /* GPIO9 ACTIVE HIGH */
+				default-brightness = <5>;
+				// vdd-supply = <&uc_reg_5v0>;
+			};
+
+			battery: battery@0 {
+				compatible = "simple-battery";
+				constant-charge-current-max-microamp = <2100000>;
+				voltage-min-design-microvolt = <3300000>;
+				voltage-max-design-microvolt = <4200000>;
+			};
+
+			i2c_uconsole: i2c@0 {
+				reg = <3>;
+				compatible = "i2c-gpio";
+				gpios = <&gpio 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN) /* sda */
+					 &gpio 1 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN) /* scl */
+					>;
+				i2c-gpio,delay-us = <2>;        /* ~100 kHz */
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			/* TPS61178, the supply for 5V bus, including USB, backlight
+			 */
+			// uc_reg_5v0: uc-reg-5v0 {
+			// 	compatible = "fixed-regulator";
+			// 	regulator-name = "sys-5v0";
+			// 	regulator-boot-on;
+			// 	regulator-always-on; /* cannot be turned off anyway */
+			// 	vin-supply = <&usb_power_supply>;
+			// };
+		};
+	};
+};
+
+&leds {
+	/delete-node/ led-act;
+
+	/* This is the green LED under the power button,
+	 * However this is not usable without a hardware modification(move R117 to R116)
+	 */
+	// act_led: led-act {
+	//	linux,default-trigger = "default-on";
+	// 	gpios = <&axp_gpio 0 1>; /* gpio0 on pmu, low active */
+	// 	// function = "activity";
+	// };
+
+	/* This is the orange charging LED under the power button.
+	 * Requires a patch to the pinctrl-axp209 driver, because
+	 * charge led is not a gpio thus not supported.
+	 */
+	// chg_led: led-chg {
+	// 	linux,default-trigger = "axp20x-battery-charging-blink-full-solid";
+	// 	gpios = <&axp_gpio 99 1>; /* CHGLED on pmu, low active */
+	// };
+};
+
+/* PMU */
+&i2c_uconsole {
+
+	axp22x: pmic@34 {
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		compatible = "x-powers,axp228", "x-powers,axp223", "x-powers,axp221";
+		reg = <0x34>; /* i2c address */
+		interrupt-parent = <&gpio>;
+		interrupts = <2 8>;  /* IRQ_TYPE_LEVEL_LOW */
+		irq-gpios = <&gpio 2 0>;
+
+		/* TODO: figure out the initial output states */
+		regulators {
+
+			x-powers,dcdc-freq = <3000>;
+
+			reg_dcdc1: dcdc1 {
+				regulator-name = "sys-3v3";
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			reg_dcdc3: dcdc3 {
+				regulator-name = "sys-1v8";
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			/* TODO: switch this on demand? */
+			reg_aldo1: aldo1 {
+				regulator-name = "aud-3v3";
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			reg_aldo2: aldo2 {
+				regulator-name = "disp-3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			/* DLDO2-DLDO4 are connected in parallel.
+			 * They seem not necessary, BUT they are connected to the TPS2553's enable pin!
+			 * Disable them will shutdown the USB 5V line.
+			 */
+			reg_dldo2: dldo2 {
+				regulator-name = "vcc-3v3-ext-a";
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			reg_dldo3: dldo3 {
+				regulator-name = "vcc-3v3-ext-b";
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			reg_dldo4: dldo4 {
+				regulator-name = "vcc-3v3-ext-c";
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+
+		battery_power_supply: battery-power-supply {
+			compatible = "x-powers,axp221-battery-power-supply";
+			monitored-battery = <&battery>;
+		};
+
+		ac_power_supply: ac_power_supply {
+			compatible = "x-powers,axp221-ac-power-supply";
+		};
+
+		axp_adc: adc {
+			compatible = "x-powers,axp221-adc";
+			#io-channel-cells = <1>;
+		};
+
+		axp_gpio: gpio {
+			compatible = "x-powers,axp221-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+
+			gpio0_out: gpio0-out-pin {
+				pins = "GPIO0";
+				function = "gpio_out";
+			};
+		};
+
+		/* IPSOUT, feed to on-board buck to get 5V output */
+		/* TODO: figure out how to configure it properly */
+		usb_power_supply: usb-power {
+			compatible = "x-powers,axp221-usb-power-supply";
+		};
+	};
+};
+
+&dsi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	port {
+		dsi_out_port: endpoint {
+			remote-endpoint = <&panel_dsi_port>;
+		};
+	};
+
+	panel_cwu50: panel@0 {
+		compatible = "clockwork,cwu50";
+		reg = <0>;
+		reset-gpio = <&gpio 8 1>; /* GPIO8 ACTIVE LOW */
+		backlight = <&ocp8178_backlight>;
+		rotation = <90>;
+		iovcc-supply = <&reg_dcdc3>;
+		vci-supply = <&reg_aldo2>;
+
+		port {
+			panel_dsi_port: endpoint {
+				remote-endpoint = <&dsi_out_port>;
+			};
+		};
+	};
+};