[ Upstream commit 99b922f9ed ]
[why]
Some dongle doesn't have a valid extended dongle caps,
but we still set the extended dongle caps to be valid.
This causes validation fails for all timing.
[how]
If no dp_hdmi_max_pixel_clk is provided,
don't use extended dongle caps.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12750d1647 ]
[Why]
YCbCr420 packing format uses two chanels for luma, and 1
channel for both chroma component. Our previous implementation
did not account for this and results in every other pixel having
very high luma value, showing greyish color instead of black.
YCbCr444 = <Y1, Cb1, Cr1>; <Y2, Cb2, Cr2> .....
YCbCr420 = <Y1, Y2, Cb1>; <Y3, Y4, Cr1> .....
[How]
Program the second channel with the black color value for luma
as well.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Hugo Hu <Hugo.Hu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd4905a958 ]
[WHY]
On customer board, there is one pluse (1v , < 1ms) on
DDC_CLK pin when plug / unplug DP cable. Driver will read
it and config DP to HDMI/DVI dongle.
[HOW]
If there is a real dongle, DDC_CLK should be always pull high.
Try to read again to recovery this special case. Retry times = 3.
Need additional 3ms to detect DP passive dongle(3 failures)
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f79e03b1f ]
There exists a case where a flush of a plane/dma may have been triggered
& started from an async commit. If that plane/dma is subsequently disabled
by the next commit, the flush register will continue to hold the flush
bit for the disabled plane. Since the bit remains active,
pending_kickoff_cnt will never decrement and we'll miss frame_done
events.
This patch limits the check of flush_register to include only those bits
which have been updated with the latest commit.
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1866d44d1 ]
Fix the dsi clock names in the DSI 10nm PLL driver to
match the names in the dispcc driver as those are
according to the clock plan of the chipset.
Changes in v2:
- Update the clock diagram with the new clock name
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62d1a75287 ]
v3d_bo_get_pages() checks this to decide to map the imported buffer
instead of the backing shmem file. The caller was about to set this
value anyway, and there's no error path in between. Ideally we
wouldn't even allocate the shmem file for our imports, but that's a
more invasive fix.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 57692c94dc ("drm/v3d: Introduce a new DRM driver for Broadcom V3D V3.x+")
Link: https://patchwork.freedesktop.org/patch/msgid/20181128230927.10951-3-eric@anholt.net
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Dave Emett <david.emett@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa394b0dd6 ]
drm_atomic_helper_commit_duplicated_state() sets state->acquire_ctx to
the context given in the argument and leaves it in state after it
quits. The lifetime of state and context are not guaranteed to be the
same, so we shouldn't leave that pointer hanging around. This patch
resets the context to NULL to avoid any oopses.
Changes in v2:
- Added to the set
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181129150423.239081-1-sean@poorly.run
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08e1c28dd5 ]
[why]
phy_pix_clk is one of the variable used to check if one PLL can be shared
with displays having common mode set configuration. As of now
phy_pix_clock varialbe is calculated in function dc_validate_stream().
dc_validate_stream() function is called after clocks are assigned for the
new display. Due to this during hotplug, when PLL sharing conditions are
checked for new display phy_pix_clk variable will be 0 and for displays
that are already enabled phy_pix_clk will have some value. Hence PLL will
not be shared and if the display hardware doesn't have any more PLL to
assign, mode set will fail due to resource unavailability.
[how]
Instead of only calculating the phy_pix_clk variable after the PLL is
assigned for new display, this patch calculates phy_pix_clk also during
the before assigning the PLL for new display.
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ce504b938 ]
[why]
Gamma was always being set as identity on SDR monitor,
leading to no changes in gamma. This caused nightlight to
not apply correctly.
[how]
Added a default gamma structure to compare against
in the sdr case.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa68d4f847 ]
Some of the functions (like cdn_dp_dpcd_read, cdn_dp_get_edid_block)
allow to read 64KiB, but the cdn_dp_mailbox_read_receive, that is
used by them, can read only up to 255 bytes at once. Normally, it's
not a big issue as DPCD or EDID reads won't (hopefully) exceed that
value.
The real issue here is the revocation list read during the HDCP
authentication process. (problematic use case:
https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-4.4/drivers/gpu/drm/rockchip/cdn-dp-reg.c#1152)
The list can reach 127*5+4 bytes (num devs * 5 bytes per ID/Bksv +
4 bytes of an additional info).
In other words - CTSes with HDCP Repeater won't pass without this
fix. Oh, and the driver will most likely stop working (best case
scenario).
Signed-off-by: Damian Kos <dkos@cadence.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1541518625-25984-1-git-send-email-dkos@cadence.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0560054da5 ]
For the YUV conversion to work properly, ->x_scaling[1] should never
be set to VC4_SCALING_NONE, but vc4_get_scaling_mode() might return
VC4_SCALING_NONE if the horizontal scaling ratio exactly matches the
horizontal subsampling factor. Add a test to turn VC4_SCALING_NONE
into VC4_SCALING_PPF when that happens.
The old ->x_scaling[0] adjustment is dropped as I couldn't find any
mention to this constraint in the spec and it's proven to be
unnecessary (I tested various multi-planar YUV formats with scaling
disabled, and all of them worked fine without this adjustment).
Fixes: fc04023faf ("drm/vc4: Add support for YUV planes.")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109102633.32603-1-boris.brezillon@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 819bec35c8 ]
Prevent possible race by parallel threads between ipu_image_convert_run()
and ipu_image_convert_unprepare(). This involves setting ctx->aborting
to true unconditionally so that no new job runs can be queued during
unprepare, and holding the ctx->aborting flag until the context is freed.
Note that the "normal" ipu_image_convert_abort() case (e.g. not during
context unprepare) should clear the ctx->aborting flag after aborting
any active run and clearing the context's pending queue. This is because
it should be possible to continue to use the conversion context and queue
more runs after an abort.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c96d62215f ]
It turns out that TCON TOP registers in H6 SoC have non-zero reset
value. This may cause issues if bits are not changed during
configuration.
To prevent that, initialize registers to 0.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-24-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5c04dff24 ]
Modify vgem_init to take platform dev as parent in drm_dev_init.
This will make drm device available at "/sys/devices/platform/vgem"
in x86 chromebook.
v2: rebase, address checkpatch typo and line over 80 characters
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Deepak Sharma <deepak.sharma@amd.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023163550.15211-1-emil.l.velikov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a378050989 ]
idx can be indirectly controlled by user-space, hence leading to a
potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/gpu/drm/drm_bufs.c:1420 drm_legacy_freebufs() warn: potential
spectre issue 'dma->buflist' [r] (local cap)
Fix this by sanitizing idx before using it to index dma->buflist
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181016095549.GA23586@embeddedor.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c878a628e0 upstream.
When debugfs is disabled, but coredump is turned on, the adreno driver fails to build:
drivers/gpu/drm/msm/adreno/a3xx_gpu.c:460:4: error: 'struct msm_gpu_funcs' has no member named 'show'
.show = adreno_show,
^~~~
drivers/gpu/drm/msm/adreno/a3xx_gpu.c:460:11: note: (near initialization for 'funcs.base')
drivers/gpu/drm/msm/adreno/a3xx_gpu.c:460:11: error: initialization of 'void (*)(struct msm_gpu *, struct msm_gem_submit *, struct msm_file_private *)' from incompatible pointer type 'void (*)(struct msm_gpu *, struct msm_gpu_state *, struct drm_printer *)' [-Werror=incompatible-pointer-types]
drivers/gpu/drm/msm/adreno/a3xx_gpu.c:460:11: note: (near initialization for 'funcs.base.submit')
drivers/gpu/drm/msm/adreno/a4xx_gpu.c:546:4: error: 'struct msm_gpu_funcs' has no member named 'show'
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:1460:4: error: 'struct msm_gpu_funcs' has no member named 'show'
drivers/gpu/drm/msm/adreno/a6xx_gpu.c:769:4: error: 'struct msm_gpu_funcs' has no member named 'show'
drivers/gpu/drm/msm/msm_gpu.c: In function 'msm_gpu_devcoredump_read':
drivers/gpu/drm/msm/msm_gpu.c:289:12: error: 'const struct msm_gpu_funcs' has no member named 'show'
Adjust the #ifdef to make it build again.
Fixes: c0fec7f562 ("drm/msm/gpu: Capture the GPU state on a GPU hang")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce0210c124 upstream.
Since commit 2bcd3ecab7 when switching mode from X11 (ubuntu mate for
example) the display gets blurry, looking like an invalid framebuffer width.
This commit fixed atomic crtc modesetting in a totally wrong way and
introduced a local unnecessary ->enabled crtc state.
This commit reverts the crctc _begin() and _enable() changes and simply
adds drm_atomic_helper_commit_tail_rpm as helper.
Reported-by: Tony McKahan <tonymckahan@gmail.com>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Fixes: 2bcd3ecab7 ("drm/meson: Fixes for drm_crtc_vblank_on/off support")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[narmstrong: fixed blank line issue from checkpatch]
Link: https://patchwork.freedesktop.org/patch/msgid/20190114153118.8024-1-narmstrong@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2de42f79bb ]
Consider the following scenario:
1. nonblocking enable crtc
2. wait for the event
3. nonblocking disable crtc
On i915 this can lead to a spurious -EBUSY from step 3 on
account of non-enabled planes getting the fake_commit in step 1
and we don't complete the fake_commit-> flip_done until
drm_atomic_helper_commit_hw_done() which can happen a long
time after the flip event was sent out.
This will become somewhat easy to hit on SKL+ once we start
to add all the planes for the crtc to every modeset commit
for the purposes of forcing a watermark register programming
[1].
To make the race a little less pronounced let's complete
fake_commit->flip_done after drm_atomic_helper_wait_for_flip_done().
For the single crtc case this should make the race quite
theoretical, assuming drm_atomic_helper_wait_for_flip_done()
actually has to wait for the real commit flip_done. In case
the real commit flip_done gets completed singificantly before
drm_atomic_helper_wait_for_flip_done(), or we are dealing with
multiple crtcs whose vblanks don't line up nicely the race still
exists.
[1] https://patchwork.freedesktop.org/patch/262670/
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 080de2e5be ("drm/atomic: Check for busy planes/connectors before setting the commit")
Testcase: igt/kms_cursor_legacy/*nonblocking-modeset-vs-cursor-atomic
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181122143412.11655-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f41a895026 ]
[Why]
The igt@kms_plane@pixel-format-pipe tests can create a sequence where
stream_state is NULL during amdgpu_dm_crtc_set_crc_source which results
in a null pointer dereference.
[How]
Guard against stream_state being NULL before accessing its fields. This
doesn't fix the root cause of the issue so a DRM_ERROR is generated
to still fail the tests.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 66a8d5bfb5 upstream.
Strict requirement of pixclock to be zero breaks support of SDL 1.2
which contains hardcoded table of supported video modes with non-zero
pixclock values[1].
To better understand which pixclock values are considered valid and how
driver should handle these values, I briefly examined few existing fbdev
drivers and documentation in Documentation/fb/. And it looks like there
are no strict rules on that and actual behaviour varies:
* some drivers treat (pixclock == 0) as "use defaults" (uvesafb.c);
* some treat (pixclock == 0) as invalid value which leads to
-EINVAL (clps711x-fb.c);
* some pass converted pixclock value to hardware (uvesafb.c);
* some are trying to find nearest value from predefined table
(vga16fb.c, video_gx.c).
Given this, I believe that it should be safe to just ignore this value if
changing is not supported. It seems that any portable fbdev application
which was not written only for one specific device working under one
specific kernel version should not rely on any particular behaviour of
pixclock anyway.
However, while enabling SDL1 applications to work out of the box when
there is no /etc/fb.modes with valid settings, this change affects the
video mode choosing logic in SDL. Depending on current screen
resolution, contents of /etc/fb.modes and resolution requested by
application, this may lead to user-visible difference (not always):
image will be displayed in a right way, but it will be aligned to the
left instead of center. There is no "right behaviour" here as well, as
emulated fbdev, opposing to old fbdev drivers, simply ignores any
requsts of video mode changes with resolutions smaller than current.
The easiest way to reproduce this problem is to install sdl-sopwith[2],
remove /etc/fb.modes file if it exists, and then try to run sopwith
from console without X. At least in Fedora 29, sopwith may be simply
installed from standard repositories.
[1] SDL 1.2.15 source code, src/video/fbcon/SDL_fbvideo.c, vesa_timings
[2] http://sdl-sopwith.sourceforge.net/
Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com>
Cc: stable@vger.kernel.org
Fixes: 79e539453b ("DRM: i915: add mode setting support")
Fixes: 771fe6b912 ("drm/radeon: introduce kernel modesetting for radeon hardware")
Fixes: 785b93ef8c ("drm/kms: move driver specific fb common code to helper functions (v2)")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108072353.28078-3-mironov.ivan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51b00d8509 upstream.
This is to fix missed mmap range check on vGPU bar2 region
and only allow to map vGPU allocated GMADDR range, which means
user space should support sparse mmap to get proper offset for
mmap vGPU aperture. And this takes care of actual pgoff in mmap
request as original code always does from beginning of vGPU
aperture.
Fixes: 659643f7d8 ("drm/i915/gvt/kvmgt: add vfio/mdev support to KVMGT")
Cc: "Monroy, Rodrigo Axel" <rodrigo.axel.monroy@intel.com>
Cc: "Orrala Contreras, Alfredo" <alfredo.orrala.contreras@intel.com>
Cc: stable@vger.kernel.org # v4.10+
Reviewed-by: Hang Yuan <hang.yuan@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d1af6a11c upstream.
This is an ugly one unfortunately. Currently, all DRM drivers supporting
atomic modesetting will save the state that userspace had set before
suspending, then attempt to restore that state on resume. This probably
worked very well at one point, like many other things, until DP MST came
into the picture. While it's easy to restore state on normal display
connectors that were disconnected during suspend regardless of their
state post-resume, this can't really be done with MST because of the
fact that setting up a downstream sink requires performing sideband
transactions between the source and the MST hub, sending out the ACT
packets, etc.
Because of this, there isn't really a guarantee that we can restore the
atomic state we had before suspend once we've resumed. This sucks pretty
bad, but so far I haven't run into any compositors that this actually
causes serious issues with. Most compositors will notice the hotplug we
send afterwards, and then reprobe state.
Since nouveau and i915 also don't fail the suspend/resume process due to
failing to restore the atomic state, let's make amdgpu match this
behavior. Better to resume the GPU properly, then to stop the process
half way because of a potentially unavoidable atomic commit failure.
Eventually, we'll have a real fix for this problem on the DRM level. But
we've got some more important low-hanging fruit to deal with first.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://patchwork.freedesktop.org/patch/msgid/20190108211133.32564-3-lyude@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe7553bef8 upstream.
drm_dp_mst_topology_mgr_resume() returns whether or not it managed to
find the topology in question after a suspend resume cycle, and the
driver is supposed to check this value and disable MST accordingly if
it's gone-in addition to sending a hotplug in order to notify userspace
that something changed during suspend.
Currently, amdgpu just makes the mistake of ignoring the return code
from drm_dp_mst_topology_mgr_resume() which means that if a topology was
removed in suspend, amdgpu never notices and assumes it's still
connected which leads to all sorts of problems.
So, fix this by actually checking the rc from
drm_dp_mst_topology_mgr_resume(). Also, reformat the rest of the
function while we're at it to fix the over-indenting.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://patchwork.freedesktop.org/patch/msgid/20190108211133.32564-2-lyude@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 280d479b31 upstream.
If we fail to pin the ggtt vma slot for the ppgtt page tables, we need
to unwind the locals before reporting the error. Or else on subsequent
attempts to bind the page tables into the ggtt, we will already believe
that the vma has been pinned and continue on blithely. If something else
should happen to be at that location, choas ensues.
Fixes: a2bbf71483 ("drm/i915/gtt: Only keep gen6 page directories pinned while active")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: <stable@vger.kernel.org> # v4.19+
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181222030623.21710-1-chris@chris-wilson.co.uk
(cherry picked from commit d4de753526)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62d85b3bf9 upstream.
SDL 1.2 sets all fields related to the pixel format to zero in some
cases[1]. Prior to commit db05c48197 ("drm: fb-helper: Reject all
pixel format changing requests"), there was an unintentional workaround
for this that existed for more than a decade. First in device-specific DRM
drivers, then here in drm_fb_helper.c.
Previous code containing this workaround just ignores pixel format fields
from userspace code. Not a good thing either, as this way, driver may
silently use pixel format different from what client actually requested,
and this in turn will lead to displaying garbage on the screen. I think
that returning EINVAL to userspace in this particular case is the right
option, so I decided to left code from problematic commit untouched
instead of just reverting it entirely.
Here is the steps required to reproduce this problem exactly:
1) Compile fceux[2] with SDL 1.2.15 and without GTK or OpenGL
support. SDL should be compiled with fbdev support (which is
on by default).
2) Create /etc/fb.modes with following contents (values seems
not used, and just required to trigger problematic code in
SDL):
mode "test"
geometry 1 1 1 1 1
timings 1 1 1 1 1 1 1
endmode
3) Create ~/.fceux/fceux.cfg with following contents:
SDL.Hotkeys.Quit = 27
SDL.DoubleBuffering = 1
4) Ensure that screen resolution is at least 1280x960 (e.g.
append "video=Virtual-1:1280x960-32" to the kernel cmdline
for qemu/QXL).
5) Try to run fceux on VT with some ROM file[3]:
# ./fceux color_test.nes
[1] SDL 1.2.15 source code, src/video/fbcon/SDL_fbvideo.c,
FB_SetVideoMode()
[2] http://www.fceux.com
[3] Example ROM: https://github.com/bokuweb/rustynes/blob/master/roms/color_test.nes
Reported-by: saahriktu <mail@saahriktu.org>
Suggested-by: saahriktu <mail@saahriktu.org>
Cc: stable@vger.kernel.org
Fixes: db05c48197 ("drm: fb-helper: Reject all pixel format changing requests")
Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com>
[danvet: Delete misleading comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108072353.28078-2-mironov.ivan@gmail.com
Link: https://patchwork.freedesktop.org/patch/msgid/20190108072353.28078-2-mironov.ivan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4be9bd10e2 upstream.
Since "drm/fb: Stop leaking physical address", the default behaviour of
the DRM fbdev emulation is to set the smem_base to 0 and pass the new
FBINFO_HIDE_SMEM_START flag.
The main reason is to avoid leaking physical addresse to user-space, and
it follows a general move over the kernel code to avoid user-space to
manipulate physical addresses and then use some other mechanisms like
dma-buf to transfer physical buffer handles over multiple subsystems.
But, a lot of devices depends on closed sources binaries to enable
OpenGL hardware acceleration that uses this smem_start value to
pass physical addresses to out-of-tree modules in order to render
into these physical adresses. These should use dma-buf buffers allocated
from the DRM display device instead and stop relying on fbdev overallocation
to gather DMA memory (some HW vendors delivers GBM and Wayland capable
binaries, but older unsupported devices won't have these new binaries
and are doomed until an Open Source solution like Lima finalizes).
Since these devices heavily depends on this kind of software and because
the smem_start population was available for years, it's a breakage to
stop leaking smem_start without any alternative solutions.
This patch adds a Kconfig depending on the EXPERT config and an unsafe
kernel module parameter tainting the kernel when enabled.
A clear comment and Kconfig help text was added to clarify why and when
this patch should be reverted, but in the meantime it's a necessary
feature to keep.
Cc: Dave Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Dave Airlie <airlied@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1538136355-15383-1-git-send-email-narmstrong@baylibre.com
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6653a0e08 upstream.
Add a new pci id.
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49f1c44b58 upstream.
[Why]
If the "max bpc" isn't explicitly set in the atomic state then it
have a value of 0. This has the correct behavior of limiting a panel
to 8bpc in the case where the panel supports 8bpc. In the case of eDP
panels this isn't a true assumption - there are panels that can only
do 6bpc.
Banding occurs for these displays.
[How]
Initialize the max_bpc when the connector resets to 8bpc. Also carry
over the value when the state is duplicated.
Bugzilla: https://bugs.freedesktop.org/108825
Fixes: 307638884f72 ("drm/amd/display: Support amdgpu "max bpc" connector property")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4eda776c3c upstream.
'encoder' is dereferenced before it is null sanity checked, hence we
potentially have a null pointer dereference bug. Instead, initialise
drm_drv from encoder->dev->dev_private after we are sure 'encoder' is
not null.
Fixes: 5182c1a556 ("drm/rockchip: add an common abstracted PSR driver")
Cc: stable@vger.kernel.org
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20181013105654.11827-1-enric.balletbo@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b02a05bdc upstream.
When vc4_plane_state is duplicated ->is_yuv is left assigned to its
previous value, and we never set it back to false when switching to
a non-YUV format.
Fix that by setting ->is_yuv to false in the 'num_planes == 1' branch
of the vc4_plane_setup_clipping_and_scaling() function.
Fixes: fc04023faf ("drm/vc4: Add support for YUV planes.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181009132446.21960-1-boris.brezillon@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b89fdf7ae8 upstream.
We need to actually make sure we check this on resume since otherwise we
won't know whether or not the topology is still there once we've
resumed, which will cause us to still think the topology is connected
even after it's been removed if the removal happens mid-suspend.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c554206077 ]
If CS is submitted using guilty ctx, we terminate amdgpu_cs_parser_init
before locking ctx->lock, latter in amdgpu_cs_parser_fini we still are
trying to release the lock just becase parser->ctx != NULL.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 32e932e37e upstream.
UDL doesn't support vblank functionality so we don't need to
initialize vblank here (we are able to send page flip
completion events even without vblank initialization)
Moreover current drm_vblank_init call with num_crtcs > 0 causes
sending DRM_EVENT_FLIP_COMPLETE event with zero timestamp every
time. This breaks userspace apps (for example weston) which
relies on timestamp value.
Cc: stable@vger.kernel.org
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180928144126.21598-1-Eugeniy.Paltsev@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f20fa8d12 upstream.
Fixes an oops reading this debugfs entry on BCM7278.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180928232126.4332-4-eric@anholt.net
Fixes: 57692c94dc ("drm/v3d: Introduce a new DRM driver for Broadcom V3D V3.x+")
Cc: <stable@vger.kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 505b524032 upstream.
nr is indirectly controlled by user-space, hence leading to a
potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/gpu/drm/drm_ioctl.c:805 drm_ioctl() warn: potential spectre issue 'dev->driver->ioctls' [r]
drivers/gpu/drm/drm_ioctl.c:810 drm_ioctl() warn: potential spectre issue 'drm_ioctls' [r] (local cap)
drivers/gpu/drm/drm_ioctl.c:892 drm_ioctl_flags() warn: potential spectre issue 'drm_ioctls' [r] (local cap)
Fix this by sanitizing nr before using it to index dev->driver->ioctls
and drm_ioctls.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181220000015.GA18973@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e594a5e349 ]
When unloading the ast driver, a warning message is printed by
drm_mode_config_cleanup() because a reference is still held to one of
the drm_connector structs.
Correct this by calling drm_crtc_force_disable_all() in
ast_fbdev_destroy().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1e613f3c630c7bbc72e04a44b178259b9164d2f6.1543798395.git.sbobroff@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a9b89b2e2 ]
Replace vcn_v1_0_stop with vcn_v1_0_set_powergating_state during suspend,
to keep adev->vcn.cur_state update. It will fix VCN S3 hung issue.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 098336deb9 ]
The error checks on ret for a negative error return always fails because
the return value of iommu_map_sg() is unsigned and can never be negative.
Detected with Coccinelle:
drivers/gpu/drm/msm/msm_iommu.c:69:9-12: WARNING: Unsigned expression
compared with zero: ret < 0
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
CC: Rob Clark <robdclark@gmail.com>
CC: David Airlie <airlied@linux.ie>
CC: Julia Lawall <julia.lawall@lip6.fr>
CC: linux-arm-msm@vger.kernel.org
CC: dri-devel@lists.freedesktop.org
CC: freedreno@lists.freedesktop.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce25aa3ee6 ]
'dpu_enc' is a member of 'drm_enc'
And 'drm_enc' got allocated with devm_kzalloc in dpu_encoder_init.
This gives this error message:
./drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:459:1-6:
WARNING: invalid free of devm_ allocated data
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 081679c51e ]
It causes a WARN in drm_atomic_get_plane_state(), and is not used by
atomic (or dpu).
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee44563596 ]
SoCs that contain MDP5 have a top level wrapper called MDSS that
manages locks, power and irq for the sub-blocks within it.
Irq for HDMI is also routed through the MDSS.
Shortly after the Hot Plug Detection (HPD) is enabled in HDMI,
HDMI interrupts are recieved by the MDSS interrupt handler.
However at this moment the HDMI irq is still not mapped to
the MDSS irq domain so the HDMI irq handler cannot be called
to process the interrupts.
This leads to a flood of HDMI interrupts on CPU 0.
If we are lucky to have the HDMI initialization running on a
different CPU, it will eventually map the HDMI irq to MDSS irq
domain, the next HDMI interrupt will be handled by the HDMI irq
handler, the interrupt flood will stop and we will recover.
If the HDMI initialization is running on CPU 0, then it cannot
complete and there is nothing to stop the interrupt flood on
CPU 0. The system is stuck.
Fix this by moving the HPD enablement after the HDMI irq is
mapped to the MDSS irq domain.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bfa8897e4 ]
Instead of delaying that to the first query. Otherwise we could try to use the
SDMA for VM updates before the IB tests are done.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6e820fcd4 ]
We need to set the NO_EVICT flag on the ghost object or otherwise we are
adding it to the LRU.
When it is added to the LRU we can run into a race between destroying
and evicting it again.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b712e43e3 ]
Similar to the atomic helpers, we should enable vblank while we're
waiting for the commit to finish. DPU needs this, MDP5 seems to work
fine without it.
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
