The dotclock is often calculated in encoder .get_config(), so we
shouldn't copy the adjusted_mode to hwmode until we have read out the
dotclock.
Gets rid of some warnings like these:
[drm:drm_calc_timestamping_constants [drm]] *ERROR* crtc 21: Can't calculate constants, dotclock = 0!
[drm:i915_get_vblank_timestamp] crtc 0 is disabled
v2: Steal Maarten's idea to move crtc->mode etc. assignment too
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91428
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Bspec is very clear that Live status must be checked about before
trying to read EDID over DDC channel. This patch makes sure that HDMI
EDID is read only when live status is up.
The live status doesn't seem to perform very consistent across various
platforms when tested with different monitors. The reason behind that is
some monitors are late to provide right voltage to set live_status up.
So, after getting the interrupt, for a small duration, live status reg
fluctuates, and then settles down showing the correct staus.
This is explained here in, in a rough way:
HPD line ________________
|\ T1 = Monitor Hotplug causing IRQ
| \______________________________________
| |
| |
| | T2 = Live status is stable
| | _____________________________________
| | /|
Live status _____________|_|/ |
| | |
| | |
| | |
T0 T1 T2
(Between T1 and T2 Live status fluctuates or can be even low, depending on
the monitor)
After several experiments, we have concluded that a max delay
of 30ms is enough to allow the live status to settle down with
most of the monitors. This total delay of 30ms has been split into
a resolution of 3 retries of 10ms each, for the better cases.
This delay is kept at 30ms, keeping in consideration that, HDCP compliance
expect the HPD handler to respond a plug out in 100ms, by disabling port.
v2: Adding checks for VLV/CHV as well. Reusing old ibx and g4x functions
to check digital port status. Adding a separate function to get bxt live
status (Daniel)
v3: Using intel_encoder->hpd_pin to check the live status (Siva)
Moving the live status read to intel_hdmi_probe and passing parameter
to read/not to read the edid. (me)
v4:
* Added live status check for all platforms using
intel_digital_port_connected.
* Rebased on top of Jani's DP cleanup series
* Some monitors take time in setting the live status. So retry for few
times if this is a connect HPD
v5: Removed extra "drm/i915" from commit message. Adding Shashank's sob
which was missed.
v6: Drop the (!detect_edid && !live_status check) check because for DDI
ports which are enumerated as hdmi as well as DP, we don't have a
mechanism to differentiate between DP and hdmi inside the encoder's
hot_plug. This leads to call to the hdmi's hot_plug hook for DP as well
as hdmi which leads to issues during unplug because of the above check.
v7: Make intel_digital_port_connected global in this patch, some
reformatting of while loop, adding a print when live status is not
up. (Rodrigo)
v8: Rebase it on nightly which involved skipping the hot_plug hook for now
and letting the live_status check happen in detect until the hpd handling
part is finalized (Daniel)
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch modifies dsi_prepare() function to support the same
modeset prepare sequence for BXT also. Main changes are:
1. BXT port control register is different than VLV.
2. BXT modeset sequence needs vdisplay and hdisplay programmed
for transcoder.
3. BXT can select PIPE for MIPI transcoders.
4. BXT needs to program register MIPI_INIT_COUNT for both the ports,
even if only one is being used.
v2: Fixed Jani's review comments. Rectified the DSI Macros to get
proper register offsets using _MIPI_PORT instead of _TRANSCODER
v3: Rebased on latest drm-nightly branch. Fixed Jani's review comments.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds two new functions:
- disable_dsi_pll.
BXT DSI disable sequence and registers are
different from previous platforms.
- intel_disable_dsi_pll
wrapper function to re-use the same code for
multiple platforms. It checks platform type and
calls appropriate core pll disable function.
v2: Fixed Jani's review comments.
v3: Rebased on latest drm-nightly branch.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds new functions for BXT clock and PLL programming.
They are:
1. configure_dsi_pll for BXT.
This function does the basic math and generates the divider ratio
based on requested pixclock, and program clock registers.
2. enable_dsi_pll function.
This function programs the calculated clock values on the PLL.
3. intel_enable_dsi_pll
Wrapper function to use same code for multiple platforms. It checks the
platform and calls appropriate core pll enable function.
v2: Fixed Jani's review comments. Macros are adjusted as per convention.
v3: Removed a redundant change wrt code comment.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On BXT, We Observe timeout for forcewake request completion with 2ms polling period as given here:
[drm:fw_domains_get] ERROR render: timed out waiting for forcewake ack request.
Polling for 50ms is recommended to avoid these timeouts.
Change-Id: Ie715b0069a3049606e9602bc5e97a6511890864d
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Disable Turbo on steppings prior to B0 on BXT due to hangs seen during GT CPD exit.
Change-Id: I50c5c03f59f5ba092db19e17234951d89db42c6c
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed by: Alex Dai <yu.dai@intel.com>.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Modified HAS_CSR macro defination which earlier only supported
for skl, now added support for BXT.
v1: Initial version.
v2: Instaed of skylake/broxton check added gen9 check alone based
on review comment from Sunil.
Cc: Vetter, Daniel <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added stepping info in intel_csr.c which is required to extract
specific firmware from packaged dmc firmware.
Stepping info is aligned with current bspec info.
Cc: Vetter, Daniel <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broxton also has dmc to manage low-power display engine state.
Path of the firmware added in intel_csr.c.
Naming convention followed as <platform>_dmc_<api-version>.bin
v1: Initial version.
v2: Commit description added based on review comment from Sunil.
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On HSW at least (still testing other platforms, but should be harmless
elsewhere), the DSL reg reads back as 0 when read around vblank start
time. This ends up confusing the atomic start/end checking code, since
it causes the update to appear as if it crossed a frame count boundary.
Avoid the problem by making sure we don't return scanline_offset from
the get_crtc_scanline function. In moving the code there, I add to add
an additional delay since it could be called and have a legitimate 0
result for some time (depending on the pixel clock).
v2: move hsw dsl read hack to get_crtc_scanline (Ville)
v3: use break instead of goto (Ville)
update comment with workaround details (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=91579
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Clearing the watermarks for all pipes/planes when updating the
watermarks for a single CRTC change seems like the wrong thing to
do here. As is, this code will ony update any pipe/plane watermarks
that need updating and leave the remaining set to zero. Later, the
watermark checks in check_wm_state() will flag these zero'd out pipe/plane
watermarks and throw errors.
By clearing only the watermark values associated with the specific crtc
the other watermark values may remain unchanged.
v2: Make sure all the dirty flags are cleared. Damien
Clear all values assoicated with crtc/pipe being updated. Damien
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't want random people to touch these.
Especially true since we've just screwed up SKL by holding it way too
long under the preliminary flag because of some ABI issues. And now
there's howtos all over the internets about how to set this. Same
pretty much for anything else.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: drop fastboot changes, that option is gone.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently everyone and their dog has their own favourite spelling
for vga_switcheroo. This makes it hard to grep dmesg for log entries
relating to vga_switcheroo. It also makes it hard to find related
source files in the tree.
vga_switcheroo.c uses pr_fmt "vga_switcheroo". Use that everywhere.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds an "Overview" DOC section plus two DOC sections for the modes
of use ("Manual switching and manual power control" and "Driver power
control").
Also included is kernel-doc for all public functions, structs and enums.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SKL port E handling was added in
commit 26951caf55
Author: Xiong Zhang <xiong.y.zhang@intel.com>
Date: Mon Aug 17 15:55:50 2015 +0800
drm/i915/skl: enable DDI-E hotplug
but the whole function was moved in a another branch in
commit b93433ccf6
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Aug 20 10:47:36 2015 +0300
drm/i915: move ibx_digital_port_connected to intel_dp.c
and the addition was lost at some backmerge that I was unable to
identify. Put it back in.
Tested-by: Tomi Sarvela <tomix.p.sarvela@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Fix the following 'make htmldocs' warnings:
.//drivers/gpu/drm/i915/intel_audio.c:439: warning: No description found for parameter 'intel_encoder'
.//drivers/gpu/drm/i915/intel_audio.c:439: warning: Excess function parameter 'encoder' description in 'intel_audio_codec_disable'
.//drivers/gpu/drm/i915/intel_audio.c:439: warning: No description found for parameter 'intel_encoder'
.//drivers/gpu/drm/i915/intel_audio.c:439: warning: Excess function parameter 'encoder' description in 'intel_audio_codec_disable'
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Not the first time! not the last time?
There is a possibility to use gcc 5's -Wbool-compare to try and compare
(reg) in those macros to a constant and gcc will warn that the
comparison between a boolean expression and a constant is always either
true or false. Maybe.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We allocate memory for LVDS modes while parsing the VBT at startup, but
never free this memory when the driver is unloaded, causing a small
leak.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Use the new debug info in the intel_crtc struct in these functions
rather than passing them as args.
v2: move min/max assignment back above first trace call (Ville)
use scanline from crtc->debug rather than fetching a new one (Ville)
v3: fix up trace_i915_pipe_update_end, needs end scanline (Ville)
Requested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
ioremap_cache() is currently not available on some architectures.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
I used these additional fields to track down the issue I saw on HSW.
v2: move debug fields into a substruct (Ville)
v3: clean up debug code more (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=91579
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Fix the following 'make htmldocs' warnings:
.//drivers/gpu/drm/i915/i915_gem.c:1729: warning: No description found for parameter 'vma'
.//drivers/gpu/drm/i915/i915_gem.c:1729: warning: No description found for parameter 'vmf'
.//drivers/gpu/drm/i915/i915_gem.c:4962: warning: No description found for parameter 'old'
.//drivers/gpu/drm/i915/i915_gem.c:4962: warning: No description found for parameter 'new'
.//drivers/gpu/drm/i915/i915_gem.c:4962: warning: No description found for parameter 'frontbuffer_bits'
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
i915 supports enough atomic to have atomic fb-helper paths, even though
it does not yet advertise DRIVER_ATOMIC.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for using atomic code-paths for restore_fbdev_mode().
Signed-off-by: Rob Clark <robdclark@gmail.com>
[danvet: Bikeshed comments slightly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also modify IRQ_NOPROBE and this has been maintained although it
is not clear that is really needed. There appears to be a great deal of
blind copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
We have two identical places in the overlay code which retire the drm
framebuffer. Factor these out into a common function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We can do better with armada_drm_crtc_complete_frame_work() - we can
avoid taking the event lock unless a call to drm_send_vblank_event()
is required, and using cmpxchg() and xchg(), we can eliminate the
locking around dcrtc->frame_work entirely.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When the CRTC is in low power mode, it isn't running, and so there's
no point keeping the CRTC clock enabled. Disable the CRTC clock during
DPMS.
We need to re-enable it in the mode_set callback to ensure that the
variant's compute_clock() continues to see its clock in the expected
state (enabled).
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use drm_plane_force_disable() to disable the overlay plane on a mode_set
rather than coding this ourselves.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Our vblank event code belongs in armada_crtc.c rather than the core of
the driver. Move it there.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the transition of TDA998x to the component helpers is complete,
remove the non-componentised support from the Armada DRM driver. All
outputs are expected to use the component helpers from now on.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As reading the interrupt registers clears the outstanding interrupts, we
must process all received interrupts to avoid dropping any. Rearrange
the code to achieve this, and properly check for a HPD interrupt from
the CEC_RXSHPDINT register.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
C99 types are against the style of the Linux kernel. Convert to using
Linus-friendly types. See https://lwn.net/Articles/113367/ for more
information.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 6833d26ef8 ("drm: tda998x: Fix EDID read timeout on HDMI
connect") used a weak scheme to try and delay reading EDID on a HDMI
connect event. It is weak because delaying the notification of a
hotplug event does not stop userspace from trying to read the EDID
within the 100ms delay.
The solution provided here solves this issue:
* When a HDMI connection event is detected, mark a blocking flag for
EDID reads, and start a timer for the delay.
* If an EDID read is attempted, and the blocking flag is set, wait
for the blocking flag to clear.
* When the timer expires, clear the blocking flag and wake any thread
waiting for the EDID read.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than always reporting that the interrupt was handled, we should
report whether we did handle the interrupt. Arrange to report IRQ_NONE
for cases where we found nothing to do.
This allows us to (eventually) recover from stuck-IRQ problems, rather
than causing the kernel to solidly lock up.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no way 'priv' can be NULL in tda998x_irq_thread() - this can
only happen if request_threaded_irq() was passed a NULL priv pointer,
and we would have crashed long before then if that was the case.
We also always ensure that priv->encoder is correctly setup, which
must have been initialised prior to the interrupt being claimed, so we
can remove this check as well.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the event that TTM doesn't find a compatible memory type for the
driver's first placement choice (placement without eviction), TTM
returns -EINVAL without trying the driver's second choice.
This causes problems on vmwgfx when VRAM is disabled before first modeset
and during VT switches when fbdev is not enabled.
Fix this by also trying the driver's second choice before returning
-EINVAL.
v2: Also check that man->use_type is true for the driver's second choice.
Fixes a bug where disallowed memory types could be used.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Shared frontbuffer bits are causing warnings when same FB is displayed
in another plane without clearing the bits from previous plane.
v2: Removing coversion of fb bits to 64 bit as it is not needed for now. (Daniel)
Change-Id: Ic2df80747f314b82afd22f8326297c57d1e652c6
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
[danvet: Drop INTEL_FRONTBUFFER_SPRITE_MASK since unused.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This stolen reserved stuff was introduced on g4x, so no need to waste
stolen on older platforms. Unfortunately configdb is no more so I can't
look up the right way to detect this stuff. I do have one hint as to
where the register might be on ctg, but I don't have a ctg to test it,
and on the elk I have here it doesn't contain sensible looking data.
For ilk grits suggegsts it might be in the same place as on snb (the
original PCI reg, not the mirror) but I can't be entirely sure about it
The register shows a round zero on my ilk.
So when there's no really good data for any of these platforms leave the
current "assume 1MiB" approach in place.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch fix following warnings while "make xmldocs".
.//drivers/gpu/drm/i915/intel_lrc.c:780: warning: No description
found for parameter 'req'
.//drivers/gpu/drm/i915/intel_lrc.c:780: warning: Excess function
parameter 'request' description in 'intel_logical_ring_begin'
.//drivers/gpu/drm/i915/intel_lrc.c:780: warning: Excess function
parameter 'ctx' description in 'intel_logical_ring_begin'
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Extend init/init_hw split to context init.
- Move context initialisation in to i915_gem_init_hw
- Move one off initialisation for render ring to
i915_gem_validate_context
- Move default context initialisation to logical_ring_init
Rename intel_lr_context_deferred_create to
intel_lr_context_deferred_alloc, to reflect reduced functionality &
alloc/init split.
This patch is intended to split out the allocation of resources &
initialisation to allow easier reuse of code for resume/gpu reset.
v2: Removed function ptr wrapping of do_switch_context (Daniel Vetter)
Left ->init_context int intel_lr_context_deferred_alloc
(Daniel Vetter)
Remove unnecessary init flag & ring type test. (Daniel Vetter)
Improve commit message (Daniel Vetter)
v3: On init/reinit, set the hw next sequence number to the sw next
sequence number. This is set to 1 at driver load time. This prevents
the seqno being reset on reinit (Chris Wilson)
v4: Set seqno back to ~0 - 0x1000 at start-of-day, and increment by 0x100
on reset.
This makes it obvious which bbs are which after a reset. (David Gordon
& John Harrison)
Rebase.
v5: Rebase. Fixed rebase breakage. Put context pinning in separate
function. Removed code churn. (Thomas Daniel)
v6: Cleanup up issues introduced in v2 & v5 (Thomas Daniel)
Issue: VIZ-4798
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <john.c.harrison@intel.com>
Cc: David Gordon <david.s.gordon@intel.com>
Cc: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This avoids some bad register writes and generally feels more correct
than unconditionally trying to redirect interrupts and such.
References: https://bugs.freedesktop.org/show_bug.cgi?id=91777
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use WARN_ONCE in a bunch of places and demote a message that would
continually spam us.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
