Per SD specification physical layer v4.0, section 3.9.4, it
says "UHS-I supports only 4-bit mode. Host shall select 4-bit
mode by ACMD6. However mmc_sd_init_uhs_card() still go ahead
to initialize the cards anyway, whether card or host won't
support 4-bit mode.
This breaks the platforms which only support 1-bit mode but
with a UHS-I card inserted, as all the tuning process is broken
due to this. Alternatively, we should check the return value from
mmc_set_bus_width to see if host could finish the request to switch
the bus with on its side. But that needs more thing to do than this
patch that just bails out early to try to use high speed mode if 4-bit
mode isn't available for whatever reason. And this patch could also
fix the same problem for sdio since R4_18V_PRESENT won't be set for
ocr when mmc_sdio_init_card() finds mmc_host_uhs() is false.
Note that This patch doesn't keep the checking of card->scr.sda_spec3
and comparing card->scr.bus_widths with SD_SCR_BUS_WIDTH_4 within
mmc_sd_init_uhs_card since if the sd cards response with SD_ROCR_S18A,
it definitely support UHS-I mode, which implicitly means these checks
are always true.
Change-Id: I2e91418b3216d9efac672af604014d7095bf4a1a
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
(cherry picked from https://patchwork.kernel.org/patch/10241773/)
The current io_latency_state structure includes entries for read
and write requests. There are special types of write commands
such as sync and discard (trim) commands, and the current
implementation is not general enough if we want to separate
latency histogram for such special commands.
This change makes io_latency_state structure request-type neutral.
It also changes to print the latency average.
Signed-off-by: Hyojun Kim <hyojun@google.com>
[ Upstream commit 5ef1ecf060 ]
Certain 64-bit systems (e.g. Amlogic Meson GX) require buffers to be
used for DMA to be 8-byte-aligned. struct sdio_func has an embedded
small DMA buffer not meeting this requirement.
When testing switching to descriptor chain mode in meson-gx driver
SDIO is broken therefore. Fix this by allocating the small DMA buffer
separately as kmalloc ensures that the returned memory area is
properly aligned for every basic data type.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per the databook of designware mmc controller 2.70a, table 3-2, cmd
done interrupt should be fired as soon as the the cmd is sent via
cmd line. And the response timeout interrupt should be generated
unconditioinally as well if the controller doesn't receive the resp.
However that doesn't seem to meet the fact of rockchip specified Soc
platforms using dwmmc. We have continuously found the the cmd done or
response timeout interrupt missed somehow which took us a long time to
understand what was happening. Finally we narrow down the root to
the reconstruction of sample circuit for dwmmc IP introduced by
rockchip and the buggy design sweeps over all the existing rockchip
Socs using dwmmc disastrously.
It seems no way to work around this bug without the proper break-out
mechanism so that we seek for a parallel pair the same as the handling
for missing data response timeout, namely dto timer. Adding this cto
timer seems easily to handle this bug but it's hard to restrict
the code under the rockchip specified context. So after merging this
patch, it sets up the cto timer for all the platforms using dwmmc IP
which isn't ideal but at least we don't advertise new quirk here.
Fortunately, no obvious performance regression was found by test and the
pre-existing similar catch-all timer for sdhci has proved it's an acceptant
way to make the code as robust as possible.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196321
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
[shawn.lin: rewrite the code and the commit msg throughout]
Change-Id: I47238c9758fe74b98a1dd3939f22e569261e696f
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
(cherry picked from https://patchwork.kernel.org/patch/9834331/)
* linux-linaro-lsk-v4.4-android: (521 commits)
Linux 4.4.66
ftrace/x86: Fix triple fault with graph tracing and suspend-to-ram
ARCv2: save r30 on kernel entry as gcc uses it for code-gen
nfsd: check for oversized NFSv2/v3 arguments
Input: i8042 - add Clevo P650RS to the i8042 reset list
p9_client_readdir() fix
MIPS: Avoid BUG warning in arch_check_elf
MIPS: KGDB: Use kernel context for sleeping threads
ALSA: seq: Don't break snd_use_lock_sync() loop by timeout
ALSA: firewire-lib: fix inappropriate assignment between signed/unsigned type
ipv6: check raw payload size correctly in ioctl
ipv6: check skb->protocol before lookup for nexthop
macvlan: Fix device ref leak when purging bc_queue
ip6mr: fix notification device destruction
netpoll: Check for skb->queue_mapping
net: ipv6: RTF_PCPU should not be settable from userspace
dp83640: don't recieve time stamps twice
tcp: clear saved_syn in tcp_disconnect()
sctp: listen on the sock only when it's state is listening or closed
net: ipv4: fix multipath RTM_GETROUTE behavior when iif is given
...
Conflicts:
drivers/usb/dwc3/gadget.c
include/linux/usb/quirks.h
Change-Id: I490f766b9a530b10da3107e20709538e4536a99d
In the eMMC 5.0 version of the spec, several EXT_CSD fields about
device lifetime are added.
- Two types of estimated indications reflected by averaged wear out of memory
- An indication reflected by average reserved blocks
Export the information through sysfs.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* linux-linaro-lsk-v4.4-android: (1362 commits)
Linux 4.4.30
Revert "fix minor infoleak in get_user_ex()"
Revert "x86/mm: Expand the exception table logic to allow new handling options"
Linux 4.4.29
ARM: pxa: pxa_cplds: fix interrupt handling
powerpc/nvram: Fix an incorrect partition merge
mpt3sas: Don't spam logs if logging level is 0
perf symbols: Fixup symbol sizes before picking best ones
perf symbols: Check symbol_conf.allow_aliases for kallsyms loading too
perf hists browser: Fix event group display
clk: divider: Fix clk_divider_round_rate() to use clk_readl()
clk: qoriq: fix a register offset error
s390/con3270: fix insufficient space padding
s390/con3270: fix use of uninitialised data
s390/cio: fix accidental interrupt enabling during resume
x86/mm: Expand the exception table logic to allow new handling options
dmaengine: ipu: remove bogus NO_IRQ reference
power: bq24257: Fix use of uninitialized pointer bq->charger
staging: r8188eu: Fix scheduling while atomic splat
ASoC: dapm: Fix kcontrol creation for output driver widget
...
Fix a build breakage where MMC is enabled, but BLOCK is not.
Change-Id: I0eb422d12264f0371f3368ae7c37342ef9efabaa
Signed-off-by: Mohan Srinivasan <srmohan@google.com>
commit 260b316436 upstream.
The dw_mmc driver stores the physical address of the MMIO registers
in a pointer, which requires the use of type casts, and is actually
broken if anyone ever has this device on a 32-bit SoC in registers
above 4GB. Gcc warns about this possibility when the driver is built
with ARM LPAE enabled:
mmc/host/dw_mmc.c: In function 'dw_mci_edmac_start_dma':
mmc/host/dw_mmc.c:702:17: warning: cast from pointer to integer of different size
cfg.dst_addr = (dma_addr_t)(host->phy_regs + fifo_offset);
^
mmc/host/dw_mmc-pltfm.c: In function 'dw_mci_pltfm_register':
mmc/host/dw_mmc-pltfm.c:63:19: warning: cast to pointer from integer of different size
host->phy_regs = (void *)(regs->start);
This changes the code to use resource_size_t, which gets rid of the
warning, the bug and the useless casts.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IO latency histogram change broke allmodconfig and
allnoconfig builds. This fixes those breakages.
Change-Id: I9cdae655b40ed155468f3cef25cdb74bb56c4d3e
Signed-off-by: Mohan Srinivasan <srmohan@google.com>
This patch adds a new sysfs node (latency_hist) and reports
IO (svc time) latency histograms. Disabled by default, can be
enabled by echoing 0 into latency_hist, stats can be cleared
by writing 2 into latency_hist. This commit fixes the 32 bit
build breakage in the previous commit. Tested on both 32 bit
and 64 bit arm devices.
Bug: 30677035
Change-Id: I9a615a16616d80f87e75676ac4d078a5c429dcf9
Signed-off-by: Mohan Srinivasan <srmohan@google.com>
The dw_mmc driver stores the physical address of the MMIO registers
in a pointer, which requires the use of type casts, and is actually
broken if anyone ever has this device on a 32-bit SoC in registers
above 4GB. Gcc warns about this possibility when the driver is built
with ARM LPAE enabled:
mmc/host/dw_mmc.c: In function 'dw_mci_edmac_start_dma':
mmc/host/dw_mmc.c:702:17: warning: cast from pointer to integer of different size
cfg.dst_addr = (dma_addr_t)(host->phy_regs + fifo_offset);
^
mmc/host/dw_mmc-pltfm.c: In function 'dw_mci_pltfm_register':
mmc/host/dw_mmc-pltfm.c:63:19: warning: cast to pointer from integer of different size
host->phy_regs = (void *)(regs->start);
This changes the code to use resource_size_t, which gets rid of the
warning, the bug and the useless casts.
Change-Id: I894c49cede8f0626efb80a9a3181a5385bbb2bcd
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Huang, Tao <huangtao@rock-chips.com>
(cherry picked from commit 260b316436)
Manually merge hs400es from upstream to avoid
too much rework.
Change-Id: I69821c866ba38ead929f437a16618694d92d470c
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
HS400 enhanced strobe is a new feature introduced by eMMC
spec 5.1, let's implement it and enjoy it!
please note that currently I have no much bandwith to split this
big patch into patchset. So please use, test and applied! Thanks.
Change-Id: I874f18a617a1b69e3ff56f5c134feb817b6985b9
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
This is required to support chips which use SDIO for signaling/
communication but do not implement the various card enumeration registers
as required for full SD / SDIO cards.
mmc: sdio: Fix bug where we're freeing the CIS tables we never allocated when using EMBEDDED_SDIO
mmc: Add max_blksize to embedded SDIO data
Change-Id: Ibff2e3e991e5522f55ec8c6edc25ed09f2553736
Signed-off-by: San Mehat <san@google.com>
We currently port some materials with concern to card
probling and gendisk recognization, etc. In attempt to
keep best bisecompatibe with upstream, the less legacy works
the better.
Change-Id: Ieb0e609f5cad4e889be6194f8fd8a54057a1174b
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.
in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DesignWare MMC Controller can supports two types of DMA
mode: external dma and internal dma. We get a RK312x platform
integrated dw_mmc and ARM pl330 dma controller. This patch add
edmac ops to support these platforms. I've tested it on RK31xx
platform with edmac mode and RK3288 platform with idmac mode.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds logic to the MMC core to set VQMMC. This is expected to be
called by MMC drivers like dw_mmc as part of (or instead of) their
start_signal_voltage_switch() callback.
A few notes:
* When setting the signal voltage to 3.3V we do our best to make VQMMC
and VMMC match. It's been reported that this makes some old cards
happy since they were tested back in the day before UHS when VQMMC
and VMMC were provided by the same regulator. A nice side effect of
this is that we don't end up on the hairy edge of VQMMC (2.7V),
which some EEs claim is a little too close to the minimum for
comfort.
This is done in two steps. At first we try to find a VQMMC within
a 0.3V tolerance of VMMC and if this is not supported by the
supplying regulator we try to find a suitable voltage within the
whole 2.7V-3.6V area of the spec.
* The two step approach is currently necessary, as the used
regulator_set_voltage_triplet(min, target, max) uses a simple
implementation that just tries two basic steps:
regulator_set_voltage(target, max);
regulator_set_voltage(min, target);
So with only one step with 2.7-3.6V borders, if a suitable voltage
is a bit below VMMC, we would directly get the lowest 2.7V
which some boards (like Rockchips) don't like at all.
* When setting the signal voltage to 1.8V or 1.2V we aim for that
specific voltage instead of picking the lowest one in the range.
* We very purposely don't print errors in mmc_regulator_set_vqmmc().
There are cases where the MMC core will try several different
voltages and we don't want to pollute the logs.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_CLKGATE was once invented to save power by gating the bus clock at
request inactivity. At that time it served its purpose. The modern way to
deal with power saving for these scenarios, is by using runtime PM.
Nowadays, several host drivers have deployed runtime PM, but for those
that haven't and which still cares power saving at request inactivity,
it's certainly time to deploy runtime PM as it has been around for several
years now.
To simplify code to mmc core and thus decrease maintenance efforts, this
patch removes all code related to MMC_CLKGATE.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
As there are no users of the __mmc_switch() API, except for the mmc core
itself, let's convert it from an exported function into an internal.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For some mass production of kingston eMMCs which adopt Phison's
firmware will meet an unrecoverable data conrruption occasionally
if performing trim due to a firmware bug confirmed by vendor. We
found it on Intel-C3230RK platform. So we add fixup of broken trim
for it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add a new quirk to add a s/w timer to notify the driver
to terminate current transfer and report a data timeout to the core,
if DTO interrupt does NOT come within the given time.
dw_mmc call mmc_request_done func to finish transfer depends on
DTO interrupt. If DTO interrupt does not come in sending data state,
the current transfer will be blocked.
We got the reply from synopsys:
There are two counters but both use the same value of [31:8] bits.
Data timeout counter doesn't wait for stop clock and you should get
DRTO even when the clock is not stopped.
Host Starvation timeout counter is triggered with stop clock condition.
This means that host should get DRTO and DTO interrupt.
But this case really exists, when driver reads tuning data from
card on RK3288-pink2 board. I measured waveforms by oscilloscope
and found that card clock was always on and data lines were always
holded high level in sending data state.
There are two possibility that data over interrupt doesn't come in
reading data state on RK3X SoCs:
- get command done interrupt, but doesn't get any data-related interrupt.
- get data error interrupt, but doesn't get data over interrupt.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
The dw_mci_init_dma() may decide to not use dma, but pio instead, caused
by things like wrong dma settings in the system.
Till now the code dw_mci_init_slot() always assumed that dma is available
when CONFIG_MMC_DW_IDMAC was defined, ignoring the host->use_dma var
set during dma init.
So when now the dma init failed for whatever reason, the transfer sizes
would still be set for dma transfers, especially including the maximum
block-count calculated from host->ring_size and resulting in a
[ 4.991109] ------------[ cut here ]------------
[ 4.991111] kernel BUG at drivers/mmc/core/core.c:256!
[ 4.991113] Internal error: Oops - BUG: 0 [#1] SMP ARM
because host->ring_size is 0 in this case and the slot init code uses
the wrong code to calculate the values.
Fix this by selecting the correct calculations using the host->use_dma
variable instead of the CONFIG_MMC_DW_IDMAC config option.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
For Freescale QorIQ LS1021AQDS board, there is a SDIO interrupt
in the process of resume without inserting SD adapter because of
some unknown issue. But the driver doesn't assign sdio_irq_thread
pointer. This will block the resume of kernel. This patch is used
to avoid using NULL sdio_irq_thread pointer.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the (not so unlikely) case that the mmc controller timeout budget is
enough for exactly one erase-group, the simplification of allowing one
sector has an enormous performance penalty. We optimize this special case
by introducing a flag that prohibits erase-group boundary crossing, so
that we can allow trimming more than one sector at a time.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Direct IO of filesystem had recursive searched and map the addr
itself, so mmc drivers can avoid to do the same ops in order to
improve throughput. We got 30% improvement for 4KB bs packet test.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
This commit comes from community but not upstreram.
We cannot wait for picking up such a great movement without
upstream admit it. We just take a light way to merge it and
minimize the change.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: xiaoyao <xiaoyao@rock-chips.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Totally new tuning policy for rockchip mhsc
merging from upstream and sustainable experiments
conducted by massive test using tier one customers's board.
This fine ajustment might be more durable and readable.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Xiao Yao <xiaoyao@rock-chips.com>
Test-by: Xiao Yao <xiaoyao@rock-chips.com>
Implement the select_drive_strength callback to provide
drive strength selection for Intel SPT.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the ability to set eMMC driver strength
for HS200 and HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for supporing drive strength selection
for eMMC, read the card's valid driver strengths.
Note that though the SD spec uses the term "drive strength",
the JEDEC eMMC spec uses the term "driver strength".
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for adding drive strength support
for eMMC, add drive_strength to struct mmc_card
to record the card drive strength for UHS-I modes
and HS200 / HS400. For eMMC this will be needed
when switching between HS200 and HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for supporting also eMMC drive strength,
add the 'card' as a parameter so that the callback can
distinguish different types of cards if necessary.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Initialization of UHS-I modes for SD and SDIO cards
employs a callback to allow the host driver to
choose a drive strength value. Currently that
assumes the card drive strength and host driver
type must be the same value. Change to let the
callback make that decision and return both the
card drive strength and host driver type.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
