The original bio might be submitted, so we shoud increase bi_remaining to
account for it when we deal with the error that the device is missing or
is not writeable, or we would skip the endio handle.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
The deadlock happened when we mount degraded filesystem, the reproduced
steps are following:
# mkfs.btrfs -f -m raid1 -d raid1 <dev0> <dev1>
# echo 1 > /sys/block/`basename <dev0>`/device/delete
# mount -o degraded <dev1> <mnt>
The reason was that the counter -- bi_remaining was wrong. If the missing
or unwriteable device was the last device in the mapping array, we would
not submit the original bio, so we shouldn't increase bi_remaining of it
in btrfs_end_bio(), or we would skip the final endio handle.
Fix this problem by adding a flag into btrfs bio structure. If we submit
the original bio, we will set the flag, and we increase bi_remaining counter,
or we don't.
Though there is another way to fix it -- decrease bi_remaining counter of the
original bio when we make sure the original bio is not submitted, this method
need add more check and is easy to make mistake.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
While running balance, scrub, fsstress concurrently we hit the
following kernel crash:
[56561.448845] BTRFS info (device sde): relocating block group 11005853696 flags 132
[56561.524077] BUG: unable to handle kernel NULL pointer dereference at 0000000000000078
[56561.524237] IP: [<ffffffffa038956d>] scrub_chunk.isra.12+0xdd/0x130 [btrfs]
[56561.524297] PGD 9be28067 PUD 7f3dd067 PMD 0
[56561.524325] Oops: 0000 [#1] SMP
[....]
[56561.527237] Call Trace:
[56561.527309] [<ffffffffa038980e>] scrub_enumerate_chunks+0x24e/0x490 [btrfs]
[56561.527392] [<ffffffff810abe00>] ? abort_exclusive_wait+0x50/0xb0
[56561.527476] [<ffffffffa038add4>] btrfs_scrub_dev+0x1a4/0x530 [btrfs]
[56561.527561] [<ffffffffa0368107>] btrfs_ioctl+0x13f7/0x2a90 [btrfs]
[56561.527639] [<ffffffff811c82f0>] do_vfs_ioctl+0x2e0/0x4c0
[56561.527712] [<ffffffff8109c384>] ? vtime_account_user+0x54/0x60
[56561.527788] [<ffffffff810f768c>] ? __audit_syscall_entry+0x9c/0xf0
[56561.527870] [<ffffffff811c8551>] SyS_ioctl+0x81/0xa0
[56561.527941] [<ffffffff815707f7>] tracesys+0xdd/0xe2
[...]
[56561.528304] RIP [<ffffffffa038956d>] scrub_chunk.isra.12+0xdd/0x130 [btrfs]
[56561.528395] RSP <ffff88004c0f5be8>
[56561.528454] CR2: 0000000000000078
This is because in btrfs_relocate_chunk(), we will free @bdev directly while
scrub may still hold extent mapping, and may access freed memory.
Fix this problem by wrapping freeing @bdev work into free_extent_map() which
is based on reference count.
Reported-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
When run scrub with balance, sometimes -ENOENT will be returned, since
in scrub_enumerate_chunks() will search dev_extent in *COMMIT_ROOT*, but
btrfs_lookup_block_group() will search block group in *MEMORY*, so if a
chunk is removed but not committed, -ENOENT will be returned.
However, there is no need to stop scrubbing since other chunks may be
scrubbed without problem.
So this patch changes the behavior to skip removed chunks and continue
to scrub the rest.
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
When we mounted the filesystem after the crash, we got the following
message:
BTRFS error (device xxx): block group xxxx has wrong amount of free space
BTRFS error (device xxx): failed to load free space cache for block group xxx
It is because we didn't update the metadata of the allocated space (in extent
tree) until the file data was written into the disk. During this time, there was
no information about the allocated spaces in either the extent tree nor the
free space cache. when we wrote out the free space cache at this time (commit
transaction), those spaces were lost. In fact, only the free space that is
used to store the file data had this problem, the others didn't because
the metadata of them is updated in the same transaction context.
There are many methods which can fix the above problem
- track the allocated space, and write it out when we write out the free
space cache
- account the size of the allocated space that is used to store the file
data, if the size is not zero, don't write out the free space cache.
The first one is complex and may make the performance drop down.
This patch chose the second method, we use a per-block-group variant to
account the size of that allocated space. Besides that, we also introduce
a per-block-group read-write semaphore to avoid the race between
the allocation and the free space cache write out.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
This patch makes the free space cache write out functions more readable,
and beisdes that, it also reduces the stack space that the function --
__btrfs_write_out_cache uses from 194bytes to 144bytes.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
The lock_wq wait queue is not used anywhere, therefore just remove it.
On a x86_64 system, this reduced sizeof(struct extent_buffer) from 320
bytes down to 296 bytes, which means a 4Kb page can now be used for
13 extent buffers instead of 12.
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
The Btrfs tree trylock function is poorly named. It always takes
the spinlock and backs off if the blocking lock is held. This
can lead to surprising lockups because people expect it to really be a
trylock.
This commit makes it a pure trylock, both for the spinlock and the
blocking lock. It also reworks the nested lock handling slightly to
avoid taking the read lock while a spinning write lock might be held.
Signed-off-by: Chris Mason <clm@fb.com>
This reverts commit cc0be81f00, it was
incorrect.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drivers that include ni_mio_common.c set the stc register read/write
callbacks to private functions that handle the read/write operations in
the correct manner for the hardware.
The ni_atmio and ni_mio_cs drivers use identical code to handle the
operations.
The ni_pcimio driver is a bit different due to the non-windowed setup
of the stc registers on the m series boards. For the other boards
supported by the ni_pcimio driver, the direct access of the first 8
STC registers is also disabled due to a difference on the 611x devices.
These differences can all be handled in the ni_stc_{read,write}[lw]()
helpers. Refactor the helpers and remove the callbacks from the private
data.
Also, move the helper functions the handle the mapping of the windowed
STC register offsets to M series register offset from ni_pcimio.c to
ni_mio_common.c.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drivers that include ni_mio_common.c set the read/write callbacks
to private functions that handle the read/write operations in the
correct manner for the hardware. The ni_atmio and ni_mio_cs drivers
use ioport register access and the ni_pcimio driver uses memory mapped
register access. The memory mapped base address is stored in the 'mite'
pointer in the private data which is only allocated and initialized by
the ni_pcimio driver.
Detect the need for memory mapped register access by checking if the
'mite' pointer is set in the private data and remove the callbacks
from the private data.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ni_atmio, ni_pcimio, and ni_mio_cs drivers all include this source
file to handle the common functionality of the drivers. Each of those
drivers set some function pointers in the private data to handle the
read/write operations to the normal registers.
Like done for the stc register operations, wrap these operations with
some helper functions to clarify the code a bit and make it easier to
read and maintain.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ni_atmio, ni_pcimio, and ni_mio_cs drivers all include this source
file to handle the common functionality of the drivers. Each of those
drivers set some function pointers in the private data to handle the
read/write operations to the stc registers.
Wrap these operations with some helper functions to clarify the code
a bit and make it easier to read and maintain.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is used to enable/disable the second irq on NI e-series
boards. This irq used used to generate dma requests for the counters.
There are only 2 counters (NUM_GPCT) so the default case of the switch
can never occur.
Tidy up this function and remove the unreachable BUG().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The (board->reg_type & ni_reg_m_series_mask) test is commonly used
in ni_mio_common.c to detect if the driver is being used with a
National Instruments "M series" DAQ board. Simplify the code a bit
by adding an 'is_m_series' bit-field flag to the private data.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This eliminates yet another user of rtw_get_capability23a_from_ie()
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Another case where the driver was copying IEs in front of the
probe_resp data in the management frame, when running in AP mode. This
would result in badly corrupted frames hitting the wire - ouf ouf ouf!
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Why on Earth we have two functions in the driver constructing beacon
frames is beyond me ... but one step at a time
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not sure how this happened, but one should never copy the IEs in front
of the beacon frame info. This could lead to some nasty corrupted
beacon frames hitting the wire if running AP mode - ouf!
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This gets rid of a bunch of hard coded offsets and reduces the
dependency of the ugly rtw_get_*_from_ie() functions.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already have the capability info in struct wlan_bssid_ex, no point
in searching for it once again.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull out the core info beacon_interval, capability, and tsf and update
cur_network.network with the info in rtw_add_beacon() instead of
relying on it being in ->IEs.
This will help later when getting rid of the beacon struct info from
->IEs and only carrying the actual IEs there.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to be more consistent mapping the names in wlan_bssid_ex to
those in struct ieee80211_mgmt.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No point in pulling capability info out of the IE array when it's
already stored in struct wlan_bssid_ex
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the beacon interval we already retreived in collect_bss_info()
instead of pulling it out of the saved IE array again.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point in creating a fake beacon frame to call
cfg80211_inform_bss_frame() when we can just call
cfg80211_inform_bss() with the parameters we were sticking into the
fake frame.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the conversion to generic early console, the passing of options from
the early 8250 console to the regular ttyS console was broken. This
resulted in the baud rate changing when switching consoles during boot.
This feature allows specifying a single console option on the kernel
command line rather than both an early console and regular serial tty
console. It would be nice to generalize this feature. However, it only
works if the correct baud rate can be probed early which is not the
case on many platforms which have non-standard UART clock rates. So for
now, this is left as an 8250 specific feature.
Reported-and-tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If INPCK is not set, input parity detection should be disabled. This means
parity errors should not be received from the tty driver, and the data
received should be treated normally.
SUS v3, 11.2.2, General Terminal Interface - Input Modes, states:
"If INPCK is set, input parity checking shall be enabled. If INPCK is
not set, input parity checking shall be disabled, allowing output parity
generation without input parity errors. Note that whether input parity
checking is enabled or disabled is independent of whether parity detection
is enabled or disabled (see Control Modes). If parity detection is enabled
but input parity checking is disabled, the hardware to which the terminal
is connected shall recognize the parity bit, but the terminal special file
shall not check whether or not this bit is correctly set."
Ignore parity errors reported by the tty driver when INPCK is not set, and
handle the received data normally.
Fixes: Bugzilla #71681, 'Improvement of n_tty_receive_parity_error from n_tty.c'
Reported-by: Ivan <athlon_@mail.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
Affected drivers:
8250 - all
serial_txx9
mfd
amba-pl010
amba-pl011
atmel_serial
bfin_uart
dz
ip22zilog
max310x
mxs-auart
netx-serial
pnx8xxx_uart
pxa
sb1250-duart
sccnxp
serial_ks8695
sirfsoc_uart
st-asc
vr41xx_siu
zs
sunzilog
fsl_lpuart
sunsab
ucc_uart
bcm63xx_uart
sunsu
efm32-uart
pmac_zilog
mpsc
msm_serial
m32r_sio
Unaffected drivers:
omap-serial
rp2
sa1100
imx
icom
Annotated for fixes:
altera_uart
mcf
Drivers without break detection:
21285
xilinx-uartps
altera_jtaguart
apbuart
arc-uart
clps711x
max3100
uartlite
msm_serial_hs
nwpserial
lantiq
vt8500_serial
Unknown:
samsung
mpc52xx_uart
bfin_sport_uart
cpm_uart/core
Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag'
Reported-by: Ivan <athlon_@mail.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull security maintainership update from James Morris:
"Add Serge Hallyn as security subsystem co-maintainer"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
security: add Serge Hallyn as a maintainer
arm64 tree)
- stack alignment exception entry code fix
- GHASH crypto algorithm fix and performance improvement
- CMA buffer limited to 32-bit (until a better way to describe the
system topology in DT)
- UAPI sigcontext.h build fix
- __kernel_old_{gid,uid}_t definitions fix (affecting 32-bit LTP)
- ptrace fixes (kernel fault and 32-bit arm core dump)
- pte_mknotpresent() fix
- dts updates (APM SoC)
- defconfig and Kconfig update
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=yCGm
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"These are primarily bug fixes with a performance improvement patch for
the GHASH crypto algorithm (which went in during this merging window)
and dts/defconfig/Kconfig updates.
- ftrace_return_addr() macro fix for arm (introduced earlier via the
arm64 tree)
- stack alignment exception entry code fix
- GHASH crypto algorithm fix and performance improvement
- CMA buffer limited to 32-bit (until a better way to describe the
system topology in DT)
- UAPI sigcontext.h build fix
- __kernel_old_{gid,uid}_t definitions fix (affecting 32-bit LTP)
- ptrace fixes (kernel fault and 32-bit arm core dump)
- pte_mknotpresent() fix
- dts updates (APM SoC)
- defconfig and Kconfig update"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: remove broken &= operator from pmd_mknotpresent
arm64: fix build error in sigcontext.h
arm64: dts: Add more serial port nodes in APM X-Gene device tree
arm64/dma: Removing ARCH_HAS_DMA_GET_REQUIRED_MASK macro
arm64: ptrace: fix empty registers set in prstatus of aarch32 process core
arm64: uid16: fix __kernel_old_{gid,uid}_t definitions
arm64: ptrace: change fs when passing kernel pointer to regset code
arm64: Limit the CMA buffer to 32-bit if ZONE_DMA
arm/ftrace: fix ftrace_return_addr() to ftrace_return_address()
arm64/crypto: improve performance of GHASH algorithm
arm64/crypto: fix data corruption bug in GHASH algorithm
arm64: defconfig update for LTP
arm64: ftrace: Fix comment typo 'CONFIG_FUNCTION_GRAPH_FP_TEST'
arm64: add ARCH_HAS_OPP to allow enabling OPP library
arm64: restore alphabetic order in Kconfig
arm64: Bug fix in stack alignment exception
* pm-cpufreq:
cpufreq: unlock when failing cpufreq_update_policy()
intel_pstate: Correct rounding in busy calculation
cpufreq: cpufreq-cpu0: fix CPU_THERMAL dependency
* pm-cpuidle:
cpuidle: mvebu: Fix the name of the states
* acpi-general:
ACPI: use kstrto*() instead of simple_strto*()
* acpi-processor:
ACPI / processor replace __attribute__((packed)) by __packed
* acpi-lpss:
ACPI / LPSS: Take I2C host controllers out of reset
* acpi-battery:
ACPI / battery: add quirk for Acer Aspire V5-573G
ACPI / battery: use callback for setting up quirks
New drivers
* t5403 barometric pressure sensor
* kxcjk1013 accelerometer (with a locking followup fix).
* ak09911 digital compass
Documentation
* ABI docs for proximity added (interface has been there a long time but
somehow snuck through without being documented)
* Move iio-trig-sysfs documentation out of staging (got left behind when
the driver moved some time ago).
Cleanups
* drop the timestamp argument from iio_trigger_poll(_chained) as
nothing has been done with it for some time.
* ad799x kerneldoc for ad799x_chip brought up to date.
* replace a number of reimplementations of the GENMASK macro and
use the BIT macro to cleanup a few locations.
* bring the iio_event_monitor example program up to date with new
device types.
* fix some incorrect function prototypes in iio_utils.h example code.
* INDIO_RING_TRIGGERED to INDIO_BUFFER_TRIGGERED fix in docs. This
got left behind after we renamed it a long time back.
* fix error handling in the generic_buffer example program.
* small tidy ups in the iio-trig-periodic-rtc driver.
* Allow reseting iio-trig-periodic-rtc frequency to 0 (default) after
it has changed.
* Trivial tidy ups in coding style in iio_simply_dummy
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=S0CY
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.17a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new drivers, cleanups and functionality for the 3.17 cycle.
New drivers
* t5403 barometric pressure sensor
* kxcjk1013 accelerometer (with a locking followup fix).
* ak09911 digital compass
Documentation
* ABI docs for proximity added (interface has been there a long time but
somehow snuck through without being documented)
* Move iio-trig-sysfs documentation out of staging (got left behind when
the driver moved some time ago).
Cleanups
* drop the timestamp argument from iio_trigger_poll(_chained) as
nothing has been done with it for some time.
* ad799x kerneldoc for ad799x_chip brought up to date.
* replace a number of reimplementations of the GENMASK macro and
use the BIT macro to cleanup a few locations.
* bring the iio_event_monitor example program up to date with new
device types.
* fix some incorrect function prototypes in iio_utils.h example code.
* INDIO_RING_TRIGGERED to INDIO_BUFFER_TRIGGERED fix in docs. This
got left behind after we renamed it a long time back.
* fix error handling in the generic_buffer example program.
* small tidy ups in the iio-trig-periodic-rtc driver.
* Allow reseting iio-trig-periodic-rtc frequency to 0 (default) after
it has changed.
* Trivial tidy ups in coding style in iio_simply_dummy
First round of fixes for 3.16-rc, mostly cc: stable, and the vt/vgacon
fixes from Daniel [1] to avoid hangs and unclaimed register errors on
module load/reload.
* tag 'drm-intel-fixes-2014-06-17' of git://anongit.freedesktop.org/drm-intel:
drm/i915/bdw: remove erroneous chv specific workarounds from bdw code
drm/i915: fix possible refcount leak when resetting forcewake
drm/i915: Reorder semaphore deadlock check
drm/i95: Initialize active ring->pid to -1
drm/i915: set backlight duty cycle after backlight enable for gen4
drm/i915: Avoid div-by-zero when pixel_multiplier is zero
drm/i915: Disable FBC by default also on Haswell and later
drm/i915: Kick out vga console
drm/i915: Fixup global gtt cleanup
vt: Don't ignore unbind errors in vt_unbind
vt: Fix up unregistration of vt drivers
vt: Fix replacement console check when unbinding
The acquire ctx will typically be declared on the stack, which means we
could have garbage values for any uninitialized field. In this case, it
was triggering WARN_ON()s because 'contended' had garbage value.
Go ahead and use memset() to be more future-proof.
v2: now with extra brown paper bag
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
mode validation, deep color and pageflipping fixes.
* 'drm-fixes-3.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Fix radeon_irq_kms_pflip_irq_get/put() imbalance
Revert "drm/radeon: remove drm_vblank_get|put from pflip handling"
drm/radeon: improve dvi_mode_valid
drm/radeon: update mode_valid testing for DP
drm/radeon: Use dce5/6 hdmi deep color clock setup also on dce8+
