On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
add the ability to parse "phy-handle". This
is needed for phys, which have a DT node, and
need to parse DT properties.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a gigabit ethernet PHY is connected to a fast ethernet MAC,
then it can detect 1000 support from the partner but not use it.
This results in a forced speed of 1000 and RX/TX failure.
Check for 1000BASE-T support and then check the advertisement
configuration before setting the MAC speed to 1000mbit.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-19
This series contains updates to i40e and i40evf only.
Kiran adds a spinlock around code accessing VSI MAC filter list to
ensure that we are synchronizing access to the filter list, otherwise
we can end up with multiple accesses at the same time which can cause
the VSI MAC filter list to get in an unstable or corrupted state.
Jesse fixes overlong BIT defines, where the RSS enabling call were
mistakenly missed. Also fixes a bug where the enable function was
enabling the interrupt twice while trying to update the two interrupt
throttle rate thresholds for Rx and Tx, while refactoring the IRQ
enable function to simplify reading the flow. Addressed the high
CPU utilization of some small streaming workloads that the driver should
reduce CPU in.
Anjali fixes two X722 issues with respect to EEPROM checksum verify and
reading NVM version info. Fixed where a mask value was accidentally
replaced with a bit mask causing Flow Director sideband to be broken.
Alex Duyck fixes areas of the drivers which run from hard interrupt
context or with interrupts already disabled in netpoll, so use
napi_schedule_irqoff() instead of napi_schedule().
Mitch fixes the VF drivers to not easily give up when it is not able
to communicate with the PF driver.
Carolyn fixes a problem where our tools MAC loopback test, after driver
unbind would fail because the hardware was configured for multiqueue and
unbind operation did not clear this configuration. Also fixed a issue
where the NVMUpdate tool gets bad data from the PHY when using the PHY
NVM feature because of contention on the MDIO interface from getting
PHY capability calls from the driver during regular operations.
Catherine fixed an issue where we were checking if autoneg was allowed
to change before checking if autoneg was changing, these checks need to
be in the reverse order.
Jean Sacren fixes up an function header comment to align the kernel-docs
with the actual code.
v2: Cleaned up the use of spin_is_locked() in patch 1 based on feedback
from David Miller, since it always evaluates to zero on uni-processor
builds
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Neither the rockchip i2s nor the rockchip spdif binding support child
devices so #address-cells and #size-cells properties aren't required.
Remove these from the bindings.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check if GPIO pin is valid by API helper function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new snd_pcm_hw_constraint_single() helper function rather than
installing a list constraint with a single value. Since
snd_pcm_hw_constraint_single() sets a static constraint while
snd_pcm_hw_constraint_list() sets a dynamic constraint the former is
slightly more efficient and it also needs less code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function rather than
installing a list constraint with a single value. Since
snd_pcm_hw_constraint_single() sets a static constraint while
snd_pcm_hw_constraint_list() sets a dynamic constraint the former is
slightly more efficient and it also needs less code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function rather than
installing a list constraint with a single value. Since
snd_pcm_hw_constraint_single() sets a static constraint while
snd_pcm_hw_constraint_list() sets a dynamic constraint the former is
slightly more efficient and it also needs less code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function rather than
installing a list constraint with a single value. Since
snd_pcm_hw_constraint_single() sets a static constraint while
snd_pcm_hw_constraint_list() sets a dynamic constraint the former is
slightly more efficient and it also needs less code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer and is slightly shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer and is slightly shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hci_conn objects don't have a dedicated lock themselves but rely
on the caller to hold the hci_dev lock for most types of access. The
hci_conn_timeout() function has so far sent certain HCI commands based
on the hci_conn state which has been possible without holding the
hci_dev lock.
The recent changes to do LE scanning before connect attempts added
even more operations to hci_conn and hci_dev from hci_conn_timeout,
thereby exposing potential race conditions with the hci_dev and
hci_conn states.
As an example of such a race, here there's a timeout but an
l2cap_sock_connect() call manages to race with the cleanup routine:
[Oct21 08:14] l2cap_chan_timeout: chan ee4b12c0 state BT_CONNECT
[ +0.000004] l2cap_chan_close: chan ee4b12c0 state BT_CONNECT
[ +0.000002] l2cap_chan_del: chan ee4b12c0, conn f3141580, err 111, state BT_CONNECT
[ +0.000002] l2cap_sock_teardown_cb: chan ee4b12c0 state BT_CONNECT
[ +0.000005] l2cap_chan_put: chan ee4b12c0 orig refcnt 4
[ +0.000010] hci_conn_drop: hcon f53d56e0 orig refcnt 1
[ +0.000013] l2cap_chan_put: chan ee4b12c0 orig refcnt 3
[ +0.000063] hci_conn_timeout: hcon f53d56e0 state BT_CONNECT
[ +0.000049] hci_conn_params_del: addr ee:0d:30:09:53:1f (type 1)
[ +0.000002] hci_chan_list_flush: hcon f53d56e0
[ +0.000001] hci_chan_del: hci0 hcon f53d56e0 chan f4e7ccc0
[ +0.004528] l2cap_sock_create: sock e708fc00
[ +0.000023] l2cap_chan_create: chan ee4b1770
[ +0.000001] l2cap_chan_hold: chan ee4b1770 orig refcnt 1
[ +0.000002] l2cap_sock_init: sk ee4b3390
[ +0.000029] l2cap_sock_bind: sk ee4b3390
[ +0.000010] l2cap_sock_setsockopt: sk ee4b3390
[ +0.000037] l2cap_sock_connect: sk ee4b3390
[ +0.000002] l2cap_chan_connect: 00:02:72:d9:e5:8b -> ee:0d:30:09:53:1f (type 2) psm 0x00
[ +0.000002] hci_get_route: 00:02:72:d9:e5:8b -> ee:0d:30:09:53:1f
[ +0.000001] hci_dev_hold: hci0 orig refcnt 8
[ +0.000003] hci_conn_hold: hcon f53d56e0 orig refcnt 0
Above the l2cap_chan_connect() shouldn't have been able to reach the
hci_conn f53d56e0 anymore but since hci_conn_timeout didn't do proper
locking that's not the case. The end result is a reference to hci_conn
that's not in the conn_hash list, resulting in list corruption when
trying to remove it later:
[Oct21 08:15] l2cap_chan_timeout: chan ee4b1770 state BT_CONNECT
[ +0.000004] l2cap_chan_close: chan ee4b1770 state BT_CONNECT
[ +0.000003] l2cap_chan_del: chan ee4b1770, conn f3141580, err 111, state BT_CONNECT
[ +0.000001] l2cap_sock_teardown_cb: chan ee4b1770 state BT_CONNECT
[ +0.000005] l2cap_chan_put: chan ee4b1770 orig refcnt 4
[ +0.000002] hci_conn_drop: hcon f53d56e0 orig refcnt 1
[ +0.000015] l2cap_chan_put: chan ee4b1770 orig refcnt 3
[ +0.000038] hci_conn_timeout: hcon f53d56e0 state BT_CONNECT
[ +0.000003] hci_chan_list_flush: hcon f53d56e0
[ +0.000002] hci_conn_hash_del: hci0 hcon f53d56e0
[ +0.000001] ------------[ cut here ]------------
[ +0.000461] WARNING: CPU: 0 PID: 1782 at lib/list_debug.c:56 __list_del_entry+0x3f/0x71()
[ +0.000839] list_del corruption, f53d56e0->prev is LIST_POISON2 (00000200)
The necessary fix is unfortunately more complicated than just adding
hci_dev_lock/unlock calls to the hci_conn_timeout() call path.
Particularly, the hci_conn_del() API, which expects the hci_dev lock to
be held, performs a cancel_delayed_work_sync(&hcon->disc_work) which
would lead to a deadlock if the hci_conn_timeout() call path tries to
acquire the same lock.
This patch solves the problem by deferring the cleanup work to a
separate work callback. To protect against the hci_dev or hci_conn
going away meanwhile temporary references are taken with the help of
hci_dev_hold() and hci_conn_get().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.3
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer and is slightly shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer and is slightly shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer and is slightly shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer.
While we are at it also fix some code style issues in the affected lines.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recommended and most efficient way to constraint a configuration
parameter to a single value is to set the minimum and maximum allowed
values to the same value, i.e. calling snd_pcm_hw_constraint_minmax() with
the same value for min and max.
It is not necessarily obvious though that this is the approach that should
be taken and some drivers have come up with other ways of solving this
problem, e.g. installing a list constraint with a single item. List
constraints are dynamic constraints though and hence less efficient than
the static min-max constraint.
This patch introduces a new helper function called
snd_pcm_hw_constraint_single() which only takes a single value has the same
effect as calling snd_pcm_hw_constraint_minmax() with the same values for
min and max. But it is hopefully semantically more expressive, making it
clear that this is the preferred way of setting a single value constraint.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The register value to enable gpio2 was incorrect. So fix it.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some drivers indent some lines in a very weird manner. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When introduced in commit 1b5d514, the check 'if (hid_data->cc_index >= 0)'
in 'wacom_wac_finger_pre_report' was intended to switch where the driver
got the expected number of contacts from: HID_DG_CONTACTCOUNT if the usage
was present, or 'touch_max' otherwise. Unfortunately, an oversight worthy
of a brown paper bag (specifically, that 'cc_index' could never be negative)
meant that the latter 'else' clause would never be entered.
The patch prior to this one introduced a way for 'cc_index' to be negative,
but only if HID_DG_CONTACTCOUNT is present in some report _other_ than the
one being processed. To ensure the 'else' clause is also entered for devices
which don't have HID_DG_CONTACTCOUNT on _any_ report, we add the additional
constraint that 'cc_report' be non-zero (which is true only if the usage is
present in some report).
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The cached indicies 'cc_index' and 'cc_value_index' introduced in 1b5d514
are only valid for a single report ID. If a touchscreen has multiple
reports with a HID_DG_CONTACTCOUNT usage, its possible that the values
will not be correct for the report we're handling, resulting in an
incorrect value for 'num_expected'. This has been observed with the Cintiq
Companion 2.
To address this, we store the ID of the report those indicies are valid
for in a new 'cc_report' variable. Before using them to get the expected
contact count, we first check if the ID of the report we're processing
matches 'cc_report'. If it doesn't, we update the indicies to point to
the HID_DG_CONTACTCOUNT usage of the current report (if it has one).
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Deprecates all Roccat sysfs attributes except the ones for the old Kone by
moving abi descriptions from testing to obsolete. For most devices everything
can be done using the hidraw ioctls HIDIOCGFEATURE and HIDIOCSFEATURE, so I
would suggest future removal of device specific drivers. The userspace tools
don't use these attributes for a year now. The first Kone is not fully
HID-compliant and will still need a module.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This fixes a bug where it is possible for an off-line CPU to fail to go
into a low-power state (nap/sleep/winkle), and to become unresponsive to
requests from the KVM subsystem to wake up and run a VCPU. What can
happen is that a maskable interrupt of some kind (external, decrementer,
hypervisor doorbell, or HMI) after we have called local_irq_disable() at
the beginning of pnv_smp_cpu_kill_self() and before interrupts are
hard-disabled inside power7_nap/sleep/winkle(). In this situation, the
pending event is marked in the irq_happened flag in the PACA. This
pending event prevents power7_nap/sleep/winkle from going to the
requested low-power state; instead they return immediately. We don't
deal with any of these pending event flags in the off-line loop in
pnv_smp_cpu_kill_self() because power7_nap et al. return 0 in this case,
so we will have srr1 == 0, and none of the processing to clear
interrupts or doorbells will be done.
Usually, the most obvious symptom of this is that a KVM guest will fail
with a console message saying "KVM: couldn't grab cpu N".
This fixes the problem by making sure we handle the irq_happened flags
properly. First, we hard-disable before the off-line loop. Once we have
hard-disabled, the irq_happened flags can't change underneath us. We
unconditionally clear the DEC and HMI flags: there is no processing of
timer interrupts while off-line, and the necessary HMI processing is all
done in lower-level code. We leave the EE and DBELL flags alone for the
first iteration of the loop, so that we won't fail to respond to a
split-core request that came in just before hard-disabling. Within the
loop, we handle external interrupts if the EE bit is set in irq_happened
as well as if the low-power state was interrupted by an external
interrupt. (We don't need to do the msgclr for a pending doorbell in
irq_happened, because doorbells are edge-triggered and don't remain
pending in hardware.) Then we clear both the EE and DBELL flags, and
once clear, they cannot be set again (until this CPU comes online again,
that is).
This also fixes the debug check to not be done when we just ran a KVM
guest or when the sleep didn't happen because of a pending event in
irq_happened.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit 9678cdaae9 ("Use the POWER8 Micro Partition
Prefetch Engine in KVM HV on POWER8") because the original commit had
multiple, partly self-cancelling bugs, that could cause occasional
memory corruption.
In fact the logmpp instruction was incorrectly using register r0 as the
source of the buffer address and operation code, and depending on what
was in r0, it would either do nothing or corrupt the 64k page pointed to
by r0.
The logmpp instruction encoding and the operation code definitions could
be corrected, but then there is the problem that there is no clearly
defined way to know when the hardware has finished writing to the
buffer.
The original commit attempted to work around this by aborting the
write-out before starting the prefetch, but this is ineffective in the
case where the virtual core is now executing on a different physical
core from the one where the write-out was initiated.
These problems plus advice from the hardware designers not to use the
function (since the measured performance improvement from using the
feature was actually mostly negative), mean that reverting the code is
the best option.
Fixes: 9678cdaae9 ("Use the POWER8 Micro Partition Prefetch Engine in KVM HV on POWER8")
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch affects the clocks that use fractional ndivider in their
PLL output frequency calculation. Instead of 2^20 divide factor, the
clock's ndiv integer shift was used. Fixed the bug by replacing ndiv
integer shift with 2^20 factor.
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Fixes: 5fe225c105 ("clk: iproc: add initial common clock support")
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Similar to commit b6541db ("powerpc/eeh: Block PCI config access
upon frozen PE"), this blocks the PCI config space of Broadcom
Shiner adapter until PE reset is completed, to avoid recursive
fenced PHB when dumping PCI config registers during the period
of error recovery.
~# lspci -ns 0003:03:00.0
0003:03:00.0 0200: 14e4:168a (rev 10)
~# lspci -s 0003:03:00.0
0003:03:00.0 Ethernet controller: Broadcom Corporation \
NetXtreme II BCM57800 1/10 Gigabit Ethernet (rev 10)
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This simplifies pnv_eeh_set_option() to avoid unnecessary nested
if statements, to improve readability. No functional changes.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the logic of pnv_eeh_cap_start() to pnv_eeh_find_cap()
as the function is only called by pnv_eeh_find_cap(). The logic
of both functions are pretty simple. No need to have separate
functions.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This cleans up pseries_eeh_get_state(), no functional changes:
* Return EEH_STATE_NOT_SUPPORT early when the 2nd RTAS output
argument is zero to avoid nested if statements.
* Skip clearing bits in the PE state represented by variable
"result" to simplify the code.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When one or both of the below two flags are marked in the PE state, the
PE's IO path is regarded as enabled: EEH_STATE_MMIO_ACTIVE or
EEH_STATE_MMIO_ENABLED.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On fenced PHB, the error handlers in the drivers of its subordinate
devices could return PCI_ERS_RESULT_CAN_RECOVER, indicating no reset
will be issued during the recovery. It's conflicting with the fact
that fenced PHB won't be recovered without reset.
This limits the return value from the error handlers in the drivers
of the fenced PHB's subordinate devices to PCI_ERS_RESULT_NEED_NONE
or PCI_ERS_RESULT_NEED_RESET, to ensure reset will be issued during
recovery.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, we rely on the existence of struct pci_driver::err_handler
to decide if the corresponding PCI device should be unplugged during
EEH recovery (partially hotplug case). However that check is not
sufficient. Some device drivers implement only some of the EEH error
handlers to collect diag-data. That means the driver still expects a
hotplug to recover from the EEH error.
This makes the hotplug criterion more relaxed: if the device driver
doesn't provide all necessary EEH error handlers, it will experience
hotplug during EEH recovery.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
[mpe: Minor change log rewording]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Keep the fbdev_cma pointer around so we can use it on hotplog and close
to ensure the frame buffer console is in a useful state.
Signed-off-by: Derek Foreman <derekf@osg.samsung.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This is enough for fbcon and bringing up X using
xf86-video-modesetting. It doesn't support the 3D accelerator or
power management yet.
v2: Drop FB_HELPER select thanks to Archit's patches. Do manual init
ordering instead of using the .load hook. Structure registration
more like tegra's, but still using the typical "component" code.
Drop no-op hooks for atomic_begin and mode_fixup() now that
they're optional. Drop sentinel in Makefile. Fix minor style
nits I noticed on another reread.
v3: Use the new bcm2835 clk driver to manage pixel/HSM clocks instead
of having a fixed video mode. Use exynos-style component driver
matching instead of devicetree nodes to list the component driver
instances. Rename compatibility strings to say bcm2835, and
distinguish pv0/1/2. Clean up some h/vsync code, and add in
interlaced mode setup. Fix up probe/bind error paths. Use
bitops.h macros for vc4_regs.h
v4: Include i2c.h, allow building under COMPILE_TEST, drop msleep now
that other bugs have been fixed, add timeouts to cpu_relax()
loops, rename hpd-gpio to hpd-gpios.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VC4 is the GPU (display and 3D) subsystem present on the 2835 and some
other Broadcom SoCs.
This binding follows the model of msm, imx, sti, and others, where
there is a subsystem node for the whole GPU, with nodes for the
individual HW components within it.
v2: Extend the commit message, fix several nits from Stephen Warren.
v3: Rename the compatibility strings, clean up node names, drop the
unnecessary lists of components. Use compatibility strings for
choosing CRTC HVS channel numbers. Document the HDMI clock usage.
v4: Whitespace fix, expand acronyms, move to display/ instead of gpu/,
rename "hpd-gpio" to "hpd-gpios".
Signed-off-by: Eric Anholt <eric@anholt.net>
The code is buggy and the values read from PCI are not
reliable anyway, so it is the best to just remove this code.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Clean up the functions to allocate the command, event and
ppr-log buffers. Remove redundant code and change the return
value to int.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
