Use dtb-y and always make variables to build dtbs instead of explicit
dtbs rule. This is in preparation to support building all dtbs.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Enable building all dtb files when CONFIG_OF_ALL_DTBS is enabled. The dtbs
are not really dependent on a platform being enabled or any other kernel
config, so for testing coverage it is convenient to build all of the dtbs.
In order to only build dtbs, this option can be used by creating an
allno.config file containing:
CONFIG_COMPILE_TEST=y
CONFIG_OF=y
CONFIG_OF_ALL_DTBS=y
And then running:
make KCONFIG_ALLCONFIG=1 allnoconfig
make dtbs
While building the dtbs themselves don't need a cross compiler, the
scripts dependency does need one. This can be hacked around by
commenting out "subdir-y += mod" in scripts/Makefile.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
The vfio platform driver currently sets the IRQ_NOAUTOEN before
doing the request_irq to properly handle the user masking. However
it does not clear it when de-assigning the IRQ. This brings issues
when loading the native driver again which may not explicitly enable
the IRQ. This problem was observed with xgbe driver.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The PCI VPD capability operates on a set of window registers in PCI
config space. Writing to the address register triggers either a read
or write, depending on the setting of the PCI_VPD_ADDR_F bit within
the address register. The data register provides either the source
for writes or the target for reads.
This model is susceptible to being broken by concurrent access, for
which the kernel has adopted a set of access functions to serialize
these registers. Additionally, commits like 932c435cab ("PCI: Add
dev_flags bit to access VPD through function 0") and 7aa6ca4d39
("PCI: Add VPD function 0 quirk for Intel Ethernet devices") indicate
that VPD registers can be shared between functions on multifunction
devices creating dependencies between otherwise independent devices.
Fortunately it's quite easy to emulate the VPD registers, simply
storing copies of the address and data registers in memory and
triggering a VPD read or write on writes to the address register.
This allows vfio users to avoid seeing spurious register changes from
accesses on other devices and enables the use of shared quirks in the
host kernel. We can theoretically still race with access through
sysfs, but the window of opportunity is much smaller.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
When determining whether a group is viable, we already allow devices
bound to pcieport. Generalize this to include any PCI bridge device.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
fdt_translate_address() returns OF_BAD_ADDR on error. It is defined as
a u64 value, so the variable "addr" should be defined as u64 as well.
Fixes: fb11ffe74c ("of/fdt: add FDT serial scanning for earlycon")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Recently 'perf <tool> -h' was made aware of arguments and would show
just the help for the arguments specified, but that required a strict
form, i.e.:
$ perf -h --tui
worked, but:
$ perf -h tui
didn't.
Make it support both cases and also look at the option help when neither
matches, so that he following examples works:
$ perf report -h interface
Usage: perf report [<options>]
--gtk Use the GTK2 interface
--stdio Use the stdio interface
--tui Use the TUI interface
$ perf report -h stack
Usage: perf report [<options>]
-g, --call-graph <print_type,threshold[,print_limit],order,
sort_key[,branch]>
Display call graph (stack chain/backtrace):
print_type: call graph printing style (graph|flat|fractal|none)
threshold: minimum call graph inclusion threshold (<percent>)
print_limit: maximum number of call graph entry (<number>)
order: call graph order (caller|callee)
sort_key: call graph sort key (function|address)
branch: include last branch info to call graph (branch)
Default: graph,0.5,caller,function
--max-stack <n> Set the maximum stack depth when parsing the
callchain, anything beyond the specified depth
will be ignored. Default: 127
$
Suggested-by: Ingo Molnar <mingo@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Chandler Carruth <chandlerc@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-xzqvamzqv3cv0p6w3inhols3@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The halt bits for these clocks seem wrong. I get the following
warning while booting on an msm8960-cdp:
WARNING: CPU: 0 PID: 1 at drivers/clk/qcom/clk-branch.c:97 clk_branch_toggle+0xd0/0x138()
dsi1_clk status stuck at 'on'
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.3.0-rc3-00113-g5532cfb567fe #110
Hardware name: Qualcomm (Flattened Device Tree)
[<c0216984>] (unwind_backtrace) from [<c02138f8>] (show_stack+0x10/0x14)
[<c02138f8>] (show_stack) from [<c04a525c>] (dump_stack+0x70/0xbc)
[<c04a525c>] (dump_stack) from [<c0223c70>] (warn_slowpath_common+0x78/0xb4)
[<c0223c70>] (warn_slowpath_common) from [<c0223d40>] (warn_slowpath_fmt+0x30/0x40)
[<c0223d40>] (warn_slowpath_fmt) from [<c05fc2dc>] (clk_branch_toggle+0xd0/0x138)
[<c05fc2dc>] (clk_branch_toggle) from [<c05f3f3c>] (clk_disable_unused_subtree+0x98/0x1b0)
[<c05f3f3c>] (clk_disable_unused_subtree) from [<c05f3ec4>] (clk_disable_unused_subtree+0x20/0x1b0)
[<c05f3ec4>] (clk_disable_unused_subtree) from [<c05f5474>] (clk_disable_unused+0x58/0xd8)
[<c05f5474>] (clk_disable_unused) from [<c0209710>] (do_one_initcall+0xac/0x1ec)
[<c0209710>] (do_one_initcall) from [<c0991db4>] (kernel_init_freeable+0x11c/0x1e8)
[<c0991db4>] (kernel_init_freeable) from [<c0727ae0>] (kernel_init+0x8/0xec)
[<c0727ae0>] (kernel_init) from [<c0210238>] (ret_from_fork+0x14/0x3c)
Fix the status bits and the errors go away.
Fixes: 5532cfb567 ("clk: qcom: mmcc-8960: Add DSI related clocks")
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently any time we need to access socket or core id for given cpu, we
access the sysfs topology file.
Adding a cpus_aggr_map cpu_map to cache those entries.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Kan Liang <kan.liang@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1445784728-21732-3-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding cpu_map__empty_new interface to create empty cpumap with given
size. The cpumap entries are initialized with -1.
It'll be used for caching cpu_map in following patches.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Kan Liang <kan.liang@intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1445784728-21732-2-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Because the 'perf stat record' patches will use the id_offset member
together with the priv pointer.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Kan Liang <kan.liang@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1445784728-21732-29-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
__pa() in the x86 pageattr code. Since these virtual addreses are
not part of the direct mapping or kernel text mapping, passing them
to __pa() will trigger a BUG_ON() when CONFIG_DEBUG_VIRTUAL is
enabled - Sai Praneeth Prakhya
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xdZV
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into core/efi
Pull EFI fix from Matt Fleming:
- Fix a kernel panic by not passing EFI virtual mapping addresses to
__pa() in the x86 pageattr code. Since these virtual addreses are
not part of the direct mapping or kernel text mapping, passing them
to __pa() will trigger a BUG_ON() when CONFIG_DEBUG_VIRTUAL is
enabled. (Sai Praneeth Prakhya)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The description of the XUSB_PADCTL_USB3_PAD_MUX_0 register in the Tegra124
documentation implies that all functions (pcie, usb3 and sata) can be
muxed onto to all lanes (pcie lanes 0-4 and sata lane 0). However, it has
been confirmed that this is not the case and the mux'ing options much more
limited. Unfortunately, the public documentation has not been updated to
reflect this and so detail the actual mux'ing options here by function:
Function: Lanes:
pcie1 x2: pcie3, pcie4
pcie1 x4: pcie1, pcie2, pcie3, pcie4
pcie2 x1 (option1): pcie0
pcie2 x1 (option2): pcie2
usb3 port 0: pcie0
usb3 port 1 (option 1): pcie1
usb3 port 1 (option 2): sata0
sata: sata0
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
HW and driver support the GPIO as interrupt-controller.
Document that in the DT binding.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to leave space for the NUL char.
Fixes: 8ea4484d0c ('mailbox: Add generic mechanism for testing Mailbox Controllers')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Currently there is no way to easily differentiate multiple
watchdog devices. The watchdogs are named by the order they
are probed.
1st probed watchdog: /dev/watchdog0
2nd probed watchdog: /dev/watchdog1
...
This change uses the alias of the watchdog device node for
the name of the watchdog.
aliases {
watchdog0 = "/...../...."
watchdog3 = "/..../....."
watchdog2 = "/..../....."
...
}
This will translate to...
/dev/watchdog0
/dev/watchdog3
/dev/watchdog2
v2
Assign alias number to id in watchdog_core instead of watchdog_dev.
If failed to get id, fallback to original ida_simple_get call.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The driver does not have any real architecture dependencies. To avoid
listing each architecture that might use this driver on some
FPGA-enabled platform, drop these dependencies.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add device tree binding documentation for the watchdog hardware block
on bcm7038 and newer SoCs.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A typo resulted in the watermarks for cursor planes not being calculated
correctly. Fixed the typo.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We've had many reports that some Creative sound cards with CA0132
don't work well. Some reported that it starts working after reloading
the module, while some reported it starts working when a 32bit kernel
is used. All these facts seem implying that the chip fails to
communicate when the buffer is located in 64bit address.
This patch addresses these issues by just adding AZX_DCAPS_NO_64BIT
flag to the corresponding PCI entries. I casually had a chance to
test an SB Recon3D board, and indeed this seems helping.
Although this hasn't been tested on all Creative devices, it's safer
to assume that this restriction applies to the rest of them, too. So
the flag is applied to all Creative entries.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver adds pinctrl/GPIO support for Intel Broxton. The GPIO
controller is based on the same hardware design that is already used in
Intel Sunrisepoint so we leverage the core driver here.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reserved for ACPI actually means that in such case the GPIO hardware will
not update the interrupt status register (GPI_IS) even if the pin is
configured to trigger an interrupt. It will update GPI_GPE_STS instead and
does not trigger an interrupt.
Allow using such pins as GPIOs, only prevent their usage as interrupts.
We also rename function intel_pad_reserved_for_acpi() to be
intel_pad_acpi_mode() which reflects the actual meaning better.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now usage_with_options() setup a pager before printing message so normal
printf() or pr_err() will not be shown. The usage_with_options_msg()
can be used to print some help message before usage strings.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1445701767-12731-4-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
On Intel Broxton the GPIO hardware consists of several chips that all share
the parent interrupt. It is not possible to handle this by setting chained
handler for each chip (as they will overwrite each other).
To overcome this we need to request the interrupt using devm_request_irq()
and pass IRQF_SHARED with the flags.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Returning an error instead of NULL in bgpio_map if
platform_get_resource_byname does not find a resource was introduced with
commit cf3f2a2c8b ("gpio: generic: improve error handling in bgpio_map").
This results in several qemu runtime failures with default and non-default
configurations, if attempts are made to boot from mmcblk0. Examples for
failures with multi_v7_defconfig are
Machine: vexpress-a9 dtb: vexpress-v2p-ca9
Machine: vexpress-a15 dtb: vexpress-v2p-ca15-tc1
Crash:
VFS: Cannot open root device "mmcblk0" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Looking into the code, always returning an error if bgpio_map fails
does not appear to make much sense, since the code in bgpio_setup_io
specifically supports some of the resources to be NULL.
Fixes: cf3f2a2c8b ("gpio: generic: improve error handling in bgpio_map")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For pinctrl the "default" state is applied to pins before the driver's
probe function is called. This is normally a sensible thing to do,
but in some cases can cause problems. That's because the pins will
change state before the driver is given a chance to program how those
pins should behave.
As an example you might have a regulator that is controlled by a PWM
(output high = high voltage, output low = low voltage). The firmware
might leave this pin as driven high. If we allow the driver core to
reconfigure this pin as a PWM pin before the PWM's probe function runs
then you might end up running at too low of a voltage while we probe.
Let's introudce a new "init" state. If this is defined we'll set
pinctrl to this state before probe and then "default" after probe
(unless the driver explicitly changed states already).
An alternative idea that was thought of was to use the pre-existing
"sleep" or "idle" states and add a boolean property that we should
start in that mode. This was not done because the "init" state is
needed for correctness and those other states are only present (and
only transitioned in to and out of) when (optional) power management
is enabled.
Changes in v3:
- Moved declarations to pinctrl/devinfo.h
- Fixed author/SoB
Changes in v2:
- Added comment to pinctrl_init_done() as per Linus W.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pwrseq_emmc driver does a eMMC card reset before a system reboot to
allow broken or limited ROM boot-loaders (that don't have an eMMC reset
logic) to be able to read the second stage from the eMMC.
But this has to be called before a system reboot handler and while most
of them use the priority 128, there are other restart handlers (such as
the syscon-reboot one) that use a higher priority. So, use the highest
priority to make sure that the eMMC hw is reset before a system reboot.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While IECTRL is disabled, input signals are pulled-down internally.
If pin-muxing is set up first, glitch signals (Low to High transition)
might be input to hardware blocks.
Bad case scenario:
[1] The hardware block is already running before pinctrl is handled.
(the reset is de-asserted by default or by a firmware, for example)
[2] The pin-muxing is set up. The input signals to hardware block
are pulled-down by the chip-internal biasing.
[3] The pins are input-enabled. The signals from the board reach the
hardware block.
Actually, one invalid character is input to the UART blocks for such
SoCs as PH1-LD4, PH1-sLD8, where UART devices start to run at the
power on reset.
To avoid such problems, pins should be input-enabled before muxing.
Fixes: 6e90889202 ("pinctrl: UniPhier: add UniPhier pinctrl core support")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Dai Okamura <okamura.dai@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDIO-16 family of PC/104 utility boards feature 16
optically isolated inputs and 16 optically isolated FET solid state
outputs. This driver provides GPIO support for these 32 channels of
digital I/O. Change-of-State detection interrupts are not supported.
GPIO 0-15 correspond to digital outputs 0-15, while GPIO 16-31
correspond to digital inputs 0-15. The base port address for the device
may be set via the idio_16_base module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This new compatible string, "brcm,iproc-gpio", should be used for
all new iproc-based future SoCs.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove gpio to pinctrl pin mapping code from driver and
address this through standard property "gpio-ranges".
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If GPIO controller's pins are muxed, pin-controller subsystem
need to be intimated by defining mapping between gpio and
pinmux controller. This patch adds required properties to
define this mapping via DT.
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.
in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even if we only use one gpd, we need alloc 2 gpd and make
the gpd->next pointer to the second gpd, or may get gpd checksum
error, this was checked by hardware
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
use the ios->timing directly is better
It can reflect current timing and do settings by timing
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cmd_ints_mask and data_ints_mask are constant value,
so make it to const
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sometime only need set MMC_CAP_HW_RESET for one of MMC hosts,
So set it in device tree is better.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/video/backlight/pm8941-wled.c:404:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Jukka reported about the following warning:
"NOHZ: local_softirq_pending 08"
I remember this warning and we had a similar issue when using workqueues
and calling netif_rx. See commit 5ff3fec ("mac802154: fix NOHZ
local_softirq_pending 08 warning").
This warning occurs when calling "netif_rx" inside the wrong context
(non softirq context). The net core api offers "netif_rx_ni" to call
netif_rx inside the correct softirq context.
Reported-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add additional rc traces to aid in debugging rc retry logic.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The name used to create the verbs txreq cache was not qualified with the unit
number. This causes a panic when destroying the cache on a dual HFI systems.
Create a unique name with the unit number with this patch
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using fw_sbus_load to control SBus firmware load doesn't scale across multiple
HFI1 cards in a single system. This patch ensures that the SBus firmware is
loaded once per ASIC.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
