CPPC stands for Collaborative Processor Performance Controls
and is defined in the ACPI v5.0+ spec. It describes CPU
performance controls on an abstract and continuous scale
allowing the platform (e.g. remote power processor) to flexibly
optimize CPU performance with its knowledge of power budgets
and other architecture specific knowledge.
This patch adds a shim which exports commonly used functions
to get and set CPPC specific controls for each CPU. This enables
CPUFreq drivers to gather per CPU performance data and use
with exisiting governors or even allows for customized governors
which are implemented inside CPUFreq drivers.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Reviewed-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For normal inodes, their pages are allocated with __GFP_FS, which can cause
filesystem calls when reclaiming memory.
This can incur a dead lock condition accordingly.
So, this patch addresses this problem by introducing
f2fs_grab_cache_page(.., bool for_write), which calls
grab_cache_page_write_begin() with AOP_FLAG_NOFS.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The f2fs_collapse_range and f2fs_insert_range changes the block addresses
directly. But that can cause uncovered SSA updates.
In that case, we need to give up to change the block addresses and do buffered
writes to keep filesystem consistency.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The periodic checkpoint can resolve the previous issue.
So, now we can use this again to improve the reported performance regression:
https://lkml.org/lkml/2015/10/8/20
This reverts commit 15bec0ff5a9ba6d203178fa8772259df6207942a.
This patch introduces F2FS_GOING_DOWN_METAFLUSH which flushes meta pages like
SSA blocks and then blocks all the writes.
This can be used by power-failure tests.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Commit bac2a909a0 (PCI / PM: Avoid resuming PCI devices during
system suspend) introduced a mechanism by which some PCI devices that
were runtime-suspended at the system suspend time might be left in
that state for the duration of the system suspend-resume cycle.
However, it overlooked devices that were marked as capable of waking
up the system just because PME support was detected in their PCI
config space.
Namely, in that case, device_can_wakeup(dev) returns 'true' for the
device and if the device is not configured for system wakeup,
device_may_wakeup(dev) returns 'false' and it will be resumed during
system suspend even though configuring it for system wakeup may not
really make sense at all.
To avoid this problem, simply disable PME for PCI devices that have
not been configured for system wakeup and are runtime-suspended at
the system suspend time for the duration of the suspend-resume cycle.
If the device is in D3cold, its config space is not available and it
shouldn't be written to, but that's only possible if the device
has platform PM support and the platform code is responsible for
checking whether or not the device's configuration is suitable for
system suspend in that case.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use a PWM lookup table to provide the PWM to the pwm-backlight device.
The driver has a legacy code path that is required only because boards
still use the legacy method of requesting PWMs by global ID. Replacing
these usages allows that legacy fallback to be removed.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch enables to load nf_conntrack_netlink module if
NFULNL_CFG_F_CONNTRACK config flag is specified.
Signed-off-by: Ken-ichirou MATSUZAWA <chamas@h4.dion.ne.jp>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On each next iteration of for_each_compatible_node() the reference
counter for current device node is already decreased by the loop
iterator. The manual call to of_node_get() is required only on loop
break which is not happening here.
The double of_node_get() (with enabled CONFIG_OF_DYNAMIC) lead to
decreasing the counter below expected, initial value.
Fixes: fe4034a3fa ("ARM: EXYNOS: Add missing of_node_put() when parsing power domains")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Compiling the nvme driver on 32-bit warns about a cast from a __u64
variable to a pointer:
drivers/block/nvme-core.c: In function 'nvme_submit_io':
drivers/block/nvme-core.c:1847:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void __user *)io.addr, length, NULL, 0);
The cast here is intentional and safe, so we can shut up the
gcc warning by adding an intermediate cast to 'uintptr_t'.
I had previously submitted a patch to fix this problem in the
nvme driver, but it was accepted on the same day that two new
warnings got added.
For clarification, I also change the third instance of this cast
to use uintptr_t instead of unsigned long now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d29ec8241c ("nvme: submit internal commands through the block layer")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Compiling the nvme driver on 32-bit warns about a cast from a __u64
variable to a pointer:
drivers/block/nvme-core.c: In function 'nvme_submit_io':
drivers/block/nvme-core.c:1847:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void __user *)io.addr, length, NULL, 0);
The cast here is intentional and safe, so we can shut up the
gcc warning by adding an intermediate cast to 'uintptr_t'.
I had previously submitted a patch to fix this problem in the
nvme driver, but it was accepted on the same day that two new
warnings got added.
For clarification, I also change the third instance of this cast
to use uintptr_t instead of unsigned long now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d29ec8241c ("nvme: submit internal commands through the block layer")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
for_each_child_of_node performs an of_node_put on each iteration, so
putting an of_node_put before a continue results in a double put.
The semantic match that finds this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
iterator name for_each_child_of_node;
@@
for_each_child_of_node(root, child) {
... when != of_node_get(child)
* of_node_put(child);
...
* continue;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* clk-bcm2835:
clk: bcm2835: Add support for programming the audio domain clocks
clk: bcm2835: Add binding docs for the new platform clock driver.
clk: bcm2835: Move under bcm/ with other Broadcom SoC clk drivers.
This reverts commit 8f2c9544ab.
As it breaks g_ether on my Baytrail FFRD8 device. Everything starts out
fine, but after a bit of data has been transferred it just stops
flowing.
Note that I do get a bunch of these "NOHZ: local_softirq_pending 08"
when booting the machine, but I'm not really sure if they're related
to this problem.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 70f3a9caa1.
That commit was causing a lockdep splat with g_ether and that
was interfering with proper functionality.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This adds support for enabling, disabling, and setting the rate of the
audio domain clocks. It will be necessary for setting the pixel clock
for HDMI in the VC4 driver and let us write a cpufreq driver. It will
also improve compatibility with user changes to the firmware's
config.txt, since our previous fixed clocks are unaware of it.
The firmware also has support for configuring the clocks through the
mailbox channel, but the pixel clock setup by the firmware doesn't
work, and it's Raspberry Pi specific anyway. The only conflicts we
should have with the firmware would be if we made firmware calls that
result in clock management (like opening firmware V3D or ISP access,
which we don't support in upstream), or on hardware over-thermal or
under-voltage (when the firmware would rewrite PLLB to take the ARM
out of overclock). If that happens, our cached .recalc_rate() results
would be incorrect, but that's no worse than our current state where
we used fixed clocks.
The existing fixed clocks in the code are left in place to provide
backwards compatibility with old device tree files.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some buses provide a native _update_bits() operation which for uncached
registers is faster than doing a read/modify/write cycle as it is a
single bus transaction. Add support for implementing this to regmap.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWE+cLAAoJECTWi3JdVIfQaCcH/3m85peX2dlE7KhI6gL9N76h
v4w7phygbkQqdD3v9bbbiRavkOMrrBCVNZ28uXIO/52LulrK9pzxRVTuhqdyVasO
CIWfAYinlxWJA0BnJ1E2toqXkym9PEILCixfPyYEI5iZTX3w3rosSdup9MzYTxZZ
N3Vux2bjgCiXp9hYbajITFQ9QRNXzn3hlI/Jl0/x9SkodkzCLJurMq5JAaFE+mhO
1W2S+ERvb0M5bHuyr1Bhf3Bzb8uMFTl1QK3vxRkSI9UVe3MSpQP9SZeN+ye7p7U0
hDlike9FxyLTMMnIe9XnsNEtBZmxNuAb7meF50Bi7xzItRGOIlDxB/Ak55uD4I8=
=hCDC
-----END PGP SIGNATURE-----
Merge tag 'regmap-offload-update-bits' into regmap-next
regmap: Allow buses to provide a custom update_bits() operation
Some buses provide a native _update_bits() operation which for uncached
registers is faster than doing a read/modify/write cycle as it is a
single bus transaction. Add support for implementing this to regmap.
# gpg: Signature made Tue 06 Oct 2015 16:21:47 BST using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: key 00000000 occurs more than once in the trustdb
# gpg: key 16005C11: no public key for trusted key - skipped
# gpg: key 16005C11 marked as ultimately trusted
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
This branch adds an interface for supporting devices which have separate
mask and unmask registers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV+ptkAAoJECTWi3JdVIfQeIoH/3e1rQhIJFwO+iOV8A/vWSyk
P+NlBqPRCH77NofBfmilRHSTzI7bhuW5IDaD9mMvTcXID8j9p0HvJxJPVsrWtr8X
p7MaBYjNUitIUyO1coBDQ9YIh+gtVn5GaSzmfa5o+B0g8wpAKoqqE2BG08jR8yvH
oKp+Z/RZsIpjIgTLPLvoNX6WsjkOKMH5GB7uBAv5epmDarCJsi8gb+vs8OFoITdN
lBm0PSRD77nMn1a37n0FHa79yf/pszma0ep/mU662Ym+52BtSQM/UloNheoYQZ4Z
D7cgQjeXCJo57p1sXW6L26o1LhHRy1ovtr47nV+EXa7z0u1oY5EEwxOdUzXKiCA=
=+gx/
-----END PGP SIGNATURE-----
Merge tag 'regmap-irq-unmask' into regmap-next
regmap: Support for split mask and unmask interrupt registers
This branch adds an interface for supporting devices which have separate
mask and unmask registers.
# gpg: Signature made Thu 17 Sep 2015 11:52:20 BST using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: key 00000000 occurs more than once in the trustdb
# gpg: key 16005C11: no public key for trusted key - skipped
# gpg: key 16005C11 marked as ultimately trusted
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
In preparation for deprecating ioremap_cache() convert its usage in
pxa2xx-flash to memremap.
Cc: David Woodhouse <dwmw2@infradead.org>
[brian: also convert iounmap to memunmap]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove the unneded semicolons since they are clearly a typo error.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PRM_POLCTRL_TWL_MASK and PRM_POLCTRL_TWL_MASK
macros are not used so they can be deleted.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want the tty fixes and reverts in here as well so that people can
properly test and use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The nvme driver was moved from drivers/block, losing our implicit
dependency on CONFIG_BLOCK. This makes it an explicit driver dependency.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Remove board support files for 10 years discontinued VoiceBlue board.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When calling ->done before releasing resources we could run into a
race where the SCSI midlayer sends another command and races with
the resources beeing manipulated. For libata this can't currently
happen as synchronization happens at a higher level, but I'd still
like to fix it to future proof libata and to avoid copy & paste
into SCSI drivers where this pattern has led to reproducible crashes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch is a tidy up of warnings from the autobuilder.
>> drivers/iio/light/apds9960.c:495:32: sparse: cast to restricted __le16
drivers/iio/light/apds9960.c:635:24: sparse: cast to restricted __le16
>> drivers/iio/light/apds9960.c:672:21: sparse: incorrect type in assignment (different base types)
drivers/iio/light/apds9960.c:672:21: expected unsigned short [unsigned] [usertype] buf
drivers/iio/light/apds9960.c:672:21: got restricted __le16 [usertype] <noident>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: mranostay@gmail.com
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch changes various types to the appropriate endian specific
versions. Also introduces an additional local variable to avoid
a single variable being used for both be and cpu endianness.
These aren't bugs as such, but clearing them up does make the code
clearer.
Warning was:
sparse warnings: (new ones prefixed by >>)
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:126:9: sparse: cast to restricted __be32
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:126:9: sparse: cast to restricted __be32
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:126:9: sparse: cast to restricted __be32
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:126:9: sparse: cast to restricted __be32
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:126:9: sparse: cast to restricted __be32
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:126:9: sparse: cast to restricted __be32
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:127:16: sparse: cast to restricted __be32
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:127:16: sparse: cast to restricted __be32
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:127:16: sparse: cast to restricted __be32
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:127:16: sparse: cast to restricted __be32
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:127:16: sparse: cast to restricted __be32
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:127:16: sparse: cast to restricted __be32
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:208:18: sparse: incorrect type in assignment (different base types)
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:208:18: expected unsigned short [unsigned] [addressable] [usertype] send_buf
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:208:18: got restricted __be16 [usertype] <noident>
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
>> drivers/iio/common/ms_sensors/ms_sensors_i2c.c:216:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:230:18: sparse: incorrect type in assignment (different base types)
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:230:18: expected unsigned short [unsigned] [addressable] [usertype] send_buf
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:230:18: got restricted __be16 [usertype] <noident>
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
drivers/iio/common/ms_sensors/ms_sensors_i2c.c:239:19: sparse: cast to restricted __be64
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add arch timer node to enable arch-timer support. MT8127 firmware
doesn't correctly setup arch-timer frequency and CNTVOFF, add
properties to workaround this.
This also set cpu enable-method to enable SMP.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add arch timer node to enable arch-timer support. MT8135 firmware
doesn't correctly setup arch-timer frequency and CNTVOFF, add
properties to workaround this.
This also set cpu enable-method to enable SMP.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This commit add new cpu enable method "mediatek,mt65xx-smp" and
"mediatek,mt81xx-tz-smp".
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The OMAP3 ISP is now fully supported in DT, remove its instantiation
from C code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When in the hists browser, i.e. in 'perf report' or in 'perf top', it is
possible to press '/' and specify a substring to filter by symbol name.
Clarify how to remove a filter by making the prompt be:
Please enter the name of symbol you want to see.
To remove the filter later, press / + ENTER
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-vbq2b0kyufwy6p0ctkfswcoe@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is not necessary to set registers volatile. So, return false
for default case of rt298_volatile_register.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Writing invalid command to QSPI_SPI_CMD_REG will terminate current
transfer and de-assert the chip select. This has to be done before
calling spi_finalize_current_message(). Because
spi_finalize_current_message() will mark the end of current message
transfer and schedule the next transfer. If the chipselect is not
de-asserted before calling spi_finalize_current_message() then the next
transfer will overlap with the previous transfer leading to data
corruption.
__spi_pump_message() can be called either from kthread worker context or
directly from the calling process's context. It is possible that these
two calls can race against each other. But race is serialized by
checking whether master->cur_msg == NULL (pointer to msg being handled
by transfer_one() at present). The master->cur_msg is set to NULL when
spi_finalize_current_message() is called on that message, which means
calling spi_finalize_current_message() allows __spi_sync() to pump next
message in calling process context.
Now if spi-ti-qspi calls spi_finalize_current_message() before we
terminate transfer at hardware side, if __spi_pump_message() is called
from process context then the successive transactions can overlap.
Fix this by moving writing invalid command to QSPI_SPI_CMD_REG to
before calling spi_finalize_current_message() call.
Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For cluster raid, we should not kick it from array if the disk can't be
remove from array successfully.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
