Use this rather than calling usb_gadget_disconnect and usb_gadget_connect
directly to avoid sending USB disconnect events to userspace when resetting
the bus.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Add switch to notify current USB configuration. This can be used to detect
USB connect and disconnect events.
Broadcast a change via the usb_composite class when a USB function is
enabled or disabled.
Rename usb_function.hidden to usb_function.disabled.
Signed-off-by: Mike Lockwood <lockwood@android.com>
This patch adds a notifier which can be used by subsystems that may
be interested in when a task has completely died and is about to
have it's last resource freed.
The Android lowmemory killer uses this to determine when a task
it has killed has finally given up its goods.
Signed-off-by: San Mehat <san@google.com>
This provides kernel_debugger() which can be called from an interrupt
context low level debugger wedge to execute commands that inspect
kernel state. It doesn't do much on its own.
Signed-off-by: Brian Swetland <swetland@google.com>
kernel_debugger_core: Add sysrq command.
sysrq <c> will run the sysrq command <c> and dump what
was added to the kernel log while the command ran.
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Arve Hjønnevåg <arve@android.com>
net: Fix a bitmask in PPPoPNS and rename constants in PPPoPNS and PPPoLAC.
Signed-off-by: Chia-chi Yeh <chiachi@android.com>
net: Fix a potential deadlock while releasing PPPoLAC/PPPoPNS socket.
PPP driver guarantees that no thread will be executing start_xmit() after
returning from ppp_unregister_channel(). To achieve this, a spinlock (downl)
is used. In pppolac_release(), ppp_unregister_channel() is called after sk_udp
is locked. At the same time, another thread might be running in pppolac_xmit()
with downl. Thus a deadlock will occur if the thread tries to lock sk_udp.
The same situation might happen on sk_raw in pppopns_release().
Signed-off-by: Chia-chi Yeh <chiachi@android.com>
net: Force PPPoLAC and PPPoPNS to bind an interface before creating PPP channel.
It is common to manipulate the routing table after configuring PPP device.
Since both PPPoLAC and PPPoPNS run over IP, care must be taken to make sure
that there is no loop in the routing table.
Although this can be done by adding a host route, it might still cause
problems when the interface is down for some reason.
To solve this, this patch forces both drivers to bind an interface before
creating PPP channel, so the system will not re-route the tunneling sockets
to another interface when the original one is down. Another benefit is that
now the host route is no longer required, so there is no need to remove it
when PPP channel is closed.
Signed-off-by: Chia-chi Yeh <chiachi@android.com>
net: Avoid sleep-inside-spinlock in PPPoLAC and PPPoPNS.
Since recv() and xmit() are called with a spinlock held, routines which might
sleep cannot be used. This issue is solved by following changes:
Incoming packets are now processed in backlog handler, recv_core(), instead of
recv(). Since backlog handler is always executed with socket spinlock held, the
requirement of ppp_input() is still satisfied.
Outgoing packets are now processed in workqueue handler, xmit_core(), instead of
xmit(). Note that kernel_sendmsg() is no longer used to prevent touching dead
sockets.
In release(), lock_sock() and pppox_unbind_sock() ensure that no thread is in
recv_core() or xmit(). Then socket handlers are restored before release_sock(),
so no packets will leak in backlog queue.
Signed-off-by: Chia-chi Yeh <chiachi@android.com>
net: Fix msg_iovlen in PPPoLAC and PPPoPNS.
Although any positive value should work (which is always true in both drivers),
the correct value should be 1.
Signed-off-by: Chia-chi Yeh <chiachi@android.com>
USB: android gadget: add remote wakeup attribute to android function
Add remote wakeup attribute to configuration descriptor of android
function to advertise remote wakeup capability to host
Acked-by: Allam, Suresh Reddy <sallam@qualcomm.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: android: Allow functions to handle setup requests.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Support for specifying the list of USB functions from platform data.
The main android.c gadget driver no longer has hard coded references
to the mass_storage and adb functions.
Support for computing the product ID based on tables in platform data
and the currently enabled functions.
Moved the adb enable/disable logic from android.c to f_adb.c.
Change-Id: I6259d3fb1473ed973f700e55d17744956f3527bb
Signed-off-by: Mike Lockwood <lockwood@android.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: android gadget: add remote wakeup attribute to android function
Add remote wakeup attribute to configuration descriptor of android
function to advertise remote wakeup capability to host
Acked-by: Allam, Suresh Reddy <sallam@qualcomm.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb gadget: link fixes for android composite gadget
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb gadget: Fix null pointer errors in android composite driver
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: android: Allow usb charging to draw up to 500mA instead of 250.
Signed-off-by: Rebecca Schultz Zavin <rebecca@android.com>
usb gadget: android: Add helper function for usb_gadget_connect and disconnect.
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: call switch_dev_unregister in mass storage unbind callback
This fixes a problem unloading the android gadget driver when built as a module
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: android: Add dependency on switch driver.
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: android: Fix USB WHQL Certification Issues
Submitted on behalf of RaviKumar Vembu <ravi.v@motorola.com>
Signed-off-by: Jared Suttles <jared.suttles@motorola.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: Add "usb_mass_storage" platform driver.
This will be used for configuring vendor, product and release from board file.
Submitted on behalf of RaviKumar Vembu <ravi.v@motorola.com>
Signed-off-by: Jared Suttles <jared.suttles@motorola.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: Use usb_mass_storage platform device as parent for lun
If a platform device is specified for the f_mass_storage function, use it as the
parent driver for the lun files in sysfs.
This allows a platform independent file path for controlling USB mass storage
from user space.
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: Add platform data struct for usb_mass_storage device
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: mass_storage: Fix Mass Storage Panic during PC reboot
Submitted on behalf of RaviKumar Vembu <ravi.v@motorola.com>
Signed-off-by: Jared Suttles <jared.suttles@motorola.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: f_mass_storage: Handle setup request correctly
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: f_mass_storage: Clean up wakelocks on error paths
Signed-off-by: Rebecca Schultz Zavin <rebecca@android.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
A card driver can now specify that the underlying bus should *not*
auto-resume with the rest of the system. This is useful for reducing resume
latency as well as saving power when the card driver is not using the
bus. In the future, we'll add support for manual suspend
Signed-off-by: San Mehat <san@google.com>
This is required to support chips which use SDIO for signaling/
communication but do not implement the various card enumeration registers
as required for full SD / SDIO cards.
mmc: sdio: Fix bug where we're freeing the CIS tables we never allocated when using EMBEDDED_SDIO
mmc: Add max_blksize to embedded SDIO data
Signed-off-by: San Mehat <san@google.com>
This driver allows userspace to receive notification when client
specified key combinations are pressed.
The client opens /dev/keychord and writes a list of keychords
for the driver to monitor.
The client then reads or polls /dev/keychord for notifications.
A client specified ID for the keychord is returned from read()
when a keychord press is detected.
Signed-off-by: Mike Lockwood <lockwood@android.com>
keychord: fix to build without CONFIG_PREEMPT
Change-Id: I911f13aeda4224b6fa57863bc7e8972fec8837fb
Add a platform device in the board file to specify a reset key-combo.
The first time the key-combo is detected a work function that syncs
the filesystems is scheduled. If all the keys are released and then
pressed again, it calls panic. Reboot on panic should be set for
this to work.
Change-Id: I9d54283ca1fba45e4b1ae1a407524cdda8171143
Signed-off-by: Arve Hjønnevåg <arve@android.com>
This is needed to support devices that put non-keyboard buttons in
the keyboard matrix. For instance several devices put the trackball
button in the keyboard matrix. In this case BTN_MOUSE should be
reported from the same input device as REL_X/Y.
It is also useful for devices that have multiple logical keyboard in
the same matrix. The HTC dream has a menu key on the external keyboard
and another menu key on the slide-out keyboard. With a single input
device only one of these menu keys can be mapped to KEY_MENU.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Supports keyboard matrixces, direct inputs, direct outputs and axes connected to gpios.
Change-Id: I5e921e6e3a1cc169316ee3b665f4cc21b5735114
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Nick Pelly <npelly@google.com>
Introduce a new socket ioctl, SIOCKILLADDR, that nukes all sockets
bound to the same local address. This is useful in situations with
dynamic IPs, to kill stuck connections.
Signed-off-by: Brian Swetland <swetland@google.com>
net: fix tcp_v4_nuke_addr
Signed-off-by: Dima Zavin <dima@android.com>
net: ipv4: Fix a spinlock recursion bug in tcp_v4_nuke.
We can't hold the lock while calling to tcp_done(), so we drop
it before calling. We then have to start at the top of the chain again.
Signed-off-by: Dima Zavin <dima@android.com>
net: ipv4: Fix race in tcp_v4_nuke_addr().
To fix a recursive deadlock in 2.6.29, we stopped holding the hash table lock
across tcp_done() calls. This fixed the deadlock, but introduced a race where
the socket could die or change state.
Fix: Before unlocking the hash table, we grab a reference to the socket. We
can then unlock the hash table without risk of the socket going away. We then
lock the socket, which is safe because it is pinned. We can then call
tcp_done() without recursive deadlock and without race. Upon return, we unlock
the socket and then unpin it, killing it.
Change-Id: Idcdae072b48238b01bdbc8823b60310f1976e045
Signed-off-by: Robert Love <rlove@google.com>
Acked-by: Dima Zavin <dima@android.com>
ipv4: disable bottom halves around call to tcp_done().
Signed-off-by: Robert Love <rlove@google.com>
Signed-off-by: Colin Cross <ccross@android.com>
ipv4: Move sk_error_report inside bh_lock_sock in tcp_v4_nuke_addr
When sk_error_report is called, it wakes up the user-space thread, which then
calls tcp_close. When the tcp_close is interrupted by the tcp_v4_nuke_addr
ioctl thread running tcp_done, it leaks 392 bytes and triggers a WARN_ON.
This patch moves the call to sk_error_report inside the bh_lock_sock, which
matches the locking used in tcp_v4_err.
Signed-off-by: Colin Cross <ccross@android.com>
Forward port of ashmem to 2.6.27.
Signed-off-by: Robert Love <rlove@google.com>
ashmem: Don't install fault handler for private mmaps.
Ashmem is used to create named private heaps. If this heap is backed
by a tmpfs file it will allocate two pages for every page touched.
In 2.6.27, the extra page would later be freed, but 2.6.29 does not
scan anonymous pages when running without swap so the memory is not
freed while the file is referenced. This change changes the behavior
of private ashmem mmaps to match /dev/zero instead tmpfs.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
ashmem: Add common prefix to name reported in /proc/pid/maps
Signed-off-by: Arve Hjønnevåg <arve@android.com>
ashmem: don't require a page aligned size
This makes ashmem more similar to shmem and mmap, by
not requiring the specified size to be page aligned,
instead rounding it internally as needed.
Signed-off-by: Marco Nelissen <marcone@android.com>
Signed-off-by: Rebecca Schultz <rschultz@google.com>
pmem: Use the thread group leader insted of the current thread.
Instead of keeping track of the current thread, use the thread group leader
Signed-off-by: Rebecca Schultz <rschultz@google.com>
pmem: Add some apis to reference and flush pmem files by file struct
The api to refer to pmem files by fd should be depricated, it can
cause problems if a processes fd table changes while the kernel is processing
data in a pmem file. This change adds the safer api.
Signed-off-by: Rebecca Schultz Zavin <rebecca@android.com>
pmem: Remove unused depricated fd api to pmem.
Signed-off-by: Rebecca Schultz Zavin <rebecca@android.com>
pmem: Remove error message when calling get_pmem_addr
This call is used from the mdp driver to determine if the memory
is in pmem or in the fb. We will encounter this case during normal operation
so this error message should be removed.
Signed-off-by: Rebecca Schultz Zavin <rebecca@android.com>
pmem: Add include sched.h to fix compile errors
Signed-off-by: Rebecca Schultz Zavin <rebecca@android.com>
pmem: remove HW3D_* ioctls
Signed-off-by: Dima Zavin <dima@android.com>
pmem: Expose is_pmem_file to the in-kernel users.
Signed-off-by: Dima Zavin <dima@android.com>
pmem: Make the exposed functions be noops if CONFIG_ANDROID_PMEM is not set.
Signed-off-by: Dima Zavin <dima@android.com>
misc: pmem: don't flush if file was opened with O_SYNC
Change-Id: I067218658a0d7f7ecc1fe73e9ff6b0c3b3054653
Signed-off-by: Dima Zavin <dima@android.com>
When connecting usb or the charger the device would often go back to sleep
before the charge led and screen turned on.
Change-Id: I01def6d86ddece0d4e31d2a91d176ed0975b6b9d
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Drivers can now create alarms that will use an hrtimer while the
system is running and the rtc to wake up from suspend.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
tcp: Fix >4GB writes on 64-bit.
net/9p: Mount only matching virtio channels
de2104x: fix ethtool
tproxy: check for transparent flag in ip_route_newports
ipv6: add IPv6 to neighbour table overflow warning
tcp: fix TSO FACK loss marking in tcp_mark_head_lost
3c59x: fix regression from patch "Add ethtool WOL support"
ipv6: add a missing unregister_pernet_subsys call
s390: use free_netdev(netdev) instead of kfree()
sgiseeq: use free_netdev(netdev) instead of kfree()
rionet: use free_netdev(netdev) instead of kfree()
ibm_newemac: use free_netdev(netdev) instead of kfree()
smsc911x: Add MODULE_ALIAS()
net: reset skb queue mapping when rx'ing over tunnel
br2684: fix scheduling while atomic
de2104x: fix TP link detection
de2104x: fix power management
de2104x: disable autonegotiation on broken hardware
net: fix a lockdep splat
e1000e: 82579 do not gate auto config of PHY by hardware during nominal use
...
Fixes kernel bugzilla #16603
tcp_sendmsg() truncates iov_len to an 'int' which a 4GB write to write
zero bytes, for example.
There is also the problem higher up of how verify_iovec() works. It
wants to prevent the total length from looking like an error return
value.
However it does this using 'int', but syscalls return 'long' (and
thus signed 64-bit on 64-bit machines). So it could trigger
false-positives on 64-bit as written. So fix it to use 'long'.
Reported-by: Olaf Bonorden <bono@onlinehome.de>
Reported-by: Daniel Büse <dbuese@gmx.de>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Fix rounding-bug in __unmap_single
x86/amd-iommu: Work around S3 BIOS bug
x86/amd-iommu: Set iommu configuration flags in enable-loop
x86, setup: Fix earlyprintk=serial,0x3f8,115200
x86, setup: Fix earlyprintk=serial,ttyS0,115200
This patch adds a workaround for an IOMMU BIOS problem to
the AMD IOMMU driver. The result of the bug is that the
IOMMU does not execute commands anymore when the system
comes out of the S3 state resulting in system failure. The
bug in the BIOS is that is does not restore certain hardware
specific registers correctly. This workaround reads out the
contents of these registers at boot time and restores them
on resume from S3. The workaround is limited to the specific
IOMMU chipset where this problem occurs.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
