When PMIC irq occurs, regmap-irq.c will traverse all PMIC child
interrupts from low index 0 to high index, we give fall interrupt
high priority to be called earlier than rise, so that it can be
override by late rise event. This can helps to solve key release
glitch which make a wrongly fall event immediately after rise.
Change-Id: Ieda1d6fd3c50cc36742a4740504ec7ce12ea509b
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
The RK817 & RK809 chip is a power management IC for multimedia and handheld
devices. It contains the following components:
- Regulators
- RTC
- Clkout
- Pinctrl
- Powerkey
The RK817 & RK809 core driver is registered as a platform driver and provides
communication through I2C with the host device for the different
components.
The following is the different between the RK817 and the RK809.
1、The dcdc-buck5 is a boost dcdc for RK817 and is a buck for RK809.
2、The RK817 have one switch but The Rk809 have two.
3、The RK817 have a charger and powerpatch function but RK809 not.
Change-Id: I132029c5b28978db7ae06e13c327a1edf70f5b69
Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
RK618 is a partner chip for Rockchip mobile application processor.
RK618 includes two RGB display input interface with double data rate.
With the internal MUX function, it can output 1080P HDMI signal to
TV and output RGB/LVDS/MIPI signal to TFT panel. In this case, RK618
can support dual panel (TV and TFT) display.
RK618 includes a audio codec, which with two I2S/PCM interface, two
differential microphone input and audio processing function.
Change-Id: Id18c251cbe1613de98e84c2b022826f85b3dd82b
Signed-off-by: Wyon Bi <bivvy.bi@rock-chips.com>
Due to hardware issue, boost and otg switch must be conctrolled
with special timing carefully by rk816 battery driver. Otherwise
boost maybe burn off.
Change-Id: Id28208c5b9757e1ff0e57ec5d26f1ac0afb88ad5
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Due to different irq_reg_stride of register, add individual
irq chip for battery.
Change-Id: Ic37b136ebc543d4f7bd22d5748b59df73526ccbe
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Because Buck3 don't have sleep state register, so we need a manual
switch: set BUCK3 suspend as Auto PWM mode and resume as FPWM mode.
This is for power saving in system suspend.
Change-Id: I67db458e650b6e85ed4267f0b0dcdb01dff4c635
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
RK1000's control register block need mclk for i2c communication.
So mclk should be enabled in advance.
RK1000's control register block should be registered before RK1000
TVE.
Change-Id: Iba9a2a410fe927666072f8d246995462a860ec3a
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
set rtc stopped by default, start rtc in rtc device probe.
add rtc node, whether RTC need to initialize.
Change-Id: Ifab269786f316d33149a50a18e23af1b6206d57d
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Add support for the rk818 regulator. The regulator module consists
of 4 DCDCs, 9 LDOs, 1 switch and 1 BOOST converter which is used to
power OTG and HDMI5V.
The output voltages are configurable and are meant to supply power
to the main processor and other components.
Change-Id: I129a1f22c65684615e9ae792efaa880555f0235e
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(cherry picked from commit 1137529353)
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
* linux-linaro-lsk-v4.4-android: (1362 commits)
Linux 4.4.30
Revert "fix minor infoleak in get_user_ex()"
Revert "x86/mm: Expand the exception table logic to allow new handling options"
Linux 4.4.29
ARM: pxa: pxa_cplds: fix interrupt handling
powerpc/nvram: Fix an incorrect partition merge
mpt3sas: Don't spam logs if logging level is 0
perf symbols: Fixup symbol sizes before picking best ones
perf symbols: Check symbol_conf.allow_aliases for kallsyms loading too
perf hists browser: Fix event group display
clk: divider: Fix clk_divider_round_rate() to use clk_readl()
clk: qoriq: fix a register offset error
s390/con3270: fix insufficient space padding
s390/con3270: fix use of uninitialised data
s390/cio: fix accidental interrupt enabling during resume
x86/mm: Expand the exception table logic to allow new handling options
dmaengine: ipu: remove bogus NO_IRQ reference
power: bq24257: Fix use of uninitialized pointer bq->charger
staging: r8188eu: Fix scheduling while atomic splat
ASoC: dapm: Fix kcontrol creation for output driver widget
...
commit 9a6dc64451 upstream.
set_bit() and clear_bit() take the bit number so this code is really
doing "1 << (1 << irq)" which is a double shift bug. It's done
consistently so it won't cause a problem unless "irq" is more than 4.
Fixes: 70c6cce040 ('mfd: Support 88pm80x in 80x driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7175cce1c3 upstream.
Now that open delay and sample delay for each channel is configurable
via DT, the default IDLE_TIMEOUT value is not enough as this is
calculated based on hardcoded macros. This results in driver returning
EBUSY sometimes. Fix this by increasing the timeout
value based on maximum value possible to open delay and sample delays
for each channel.
Fixes: 5dc11e8106 ("iio: adc: ti_am335x_adc: make sample delay, open delay, averaging DT parameters")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9798ac6d32 upstream.
So that callers of cros_ec_cmd_xfer() don't have to repeat boilerplate
code when checking for errors from the EC side.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update version to v7.0, main features:
1. new algorithm which is independent of time calculation in almost case,
2. remove charger detect to driver: rk818-charger.c;
3. save algorithm calculation rest value for next system power on calculation;
4. recognize system halt and reset dsoc as rsoc;
5. support hardware sample resistor selected as 10mR or 20mR;
6. optimize zero algorithm to make discharge figure more smooth;
7. fix some logic bugs.
Change-Id: I789d070693ac16102ecbe813d878a2a3c256c030
Signed-off-by: Jianhong Chen <chenjh@rock-chips.com>
The rk818 and rk808 have different way to shutdown.
Add callback(pm_shutdown) to fulfill the individual action for
each PMIC.
Change-Id: I05dc7015ffd0f82c0ab761a380865338fe1adefe
Signed-off-by: Shengfei xu <xsf@rock-chips.com>
commit 3b67262307 upstream.
The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff
instead of 0x1f) thus reading entire register as buck9's voltage. This
effectively caused regulator core to interpret values as higher voltages
than they were and then to set real voltage much lower than intended.
The buck9 provides power to other regulators, including LDO13
and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower
voltage caused SD card detection errors on Odroid XU3/XU4:
mmc1: card never left busy state
mmc1: error -110 whilst initialising SD card
During driver probe the regulator core was checking whether initial
voltage matches the constraints. With incorrect vsel_mask of 0xff and
default value of 0x50, the core interpreted this as 5 V which is outside
of constraints (3-3.775 V). Then the regulator core was adjusting the
voltage to match the constraints. With incorrect vsel_mask this new
voltage mapped to a vere low voltage in the driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the branch of chrome platform changes for v4.4. Some have been queued
up for the full 4.3 release cycle since I forgot to send them in for that
round (rebased early on to deal with fixes conflicts).
Most of these enable EC communication stuff -- Pixel 2015 support, enabling
building for ARM64 platforms, and a few fixes for memory leaks.
There's also a patch in here to allow reading/writing the verified boot
context, which depends on a sysfs patch acked by Greg.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dv1O
-----END PGP SIGNATURE-----
Merge tag 'chrome-platform-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson:
"Here's the branch of chrome platform changes for v4.4. Some have been
queued up for the full 4.3 release cycle since I forgot to send them
in for that round (rebased early on to deal with fixes conflicts).
Most of these enable EC communication stuff -- Pixel 2015 support,
enabling building for ARM64 platforms, and a few fixes for memory
leaks.
There's also a patch in here to allow reading/writing the verified
boot context, which depends on a sysfs patch acked by Greg"
* tag 'chrome-platform-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: Fix i2c-designware adapter name
platform/chrome: Support reading/writing the vboot context
sysfs: Support is_visible() on binary attributes
platform/chrome: cros_ec: Fix possible leak in led_rgb_store()
platform/chrome: cros_ec: Fix leak in sequence_store()
platform/chrome: Enable Chrome platforms on 64-bit ARM
platform/chrome: cros_ec_dev - Add a platform device ID table
platform/chrome: cros_ec_lpc - Add support for Google Pixel 2
platform/chrome: cros_ec_lpc - Use existing function to check EC result
platform/chrome: Make depends on MFD_CROS_EC instead CROS_EC_PROTO
Revert "platform/chrome: Don't make CHROME_PLATFORMS depends on X86 || ARM"
New and/or improved SoC support for this release:
- Marvell Berlin:
* Enable standard DT-based cpufreq
* Add CPU hotplug support
- Freescale:
* Ethernet init for i.MX7D
* Suspend/resume support for i.MX6UL
- Allwinner:
* Support for R8 chipset (used on NTC's $9 C.H.I.P board)
- Mediatek:
* SMP support for some platforms
- Uniphier:
* L2 support
* Cleaned up SMP support, etc.
+ A handful of other patches around above functionality, and a few other
smaller changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=h5xk
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New and/or improved SoC support for this release:
Marvell Berlin:
- Enable standard DT-based cpufreq
- Add CPU hotplug support
Freescale:
- Ethernet init for i.MX7D
- Suspend/resume support for i.MX6UL
Allwinner:
- Support for R8 chipset (used on NTC's $9 C.H.I.P board)
Mediatek:
- SMP support for some platforms
Uniphier:
- L2 support
- Cleaned up SMP support, etc.
plus a handful of other patches around above functionality, and a few
other smaller changes"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
ARM: uniphier: rework SMP operations to use trampoline code
ARM: uniphier: add outer cache support
Documentation: EXYNOS: Update bootloader interface on exynos542x
ARM: mvebu: add broken-idle option
ARM: orion5x: use mac_pton() helper
ARM: at91: pm: at91_pm_suspend_in_sram() must be 8-byte aligned
ARM: sunxi: Add R8 support
ARM: digicolor: select pinctrl/gpio driver
arm: berlin: add CPU hotplug support
arm: berlin: use non-self-cleared reset register to reset cpu
ARM: mediatek: add smp bringup code
ARM: mediatek: enable gpt6 on boot up to make arch timer working
soc: mediatek: Fix random hang up issue while kernel init
soc: ti: qmss: make acc queue support optional in the driver
soc: ti: add firmware file name as part of the driver
Documentation: dt: soc: Add description for knav qmss driver
ARM: S3C64XX: Use PWM lookup table for mach-smartq
ARM: S3C64XX: Use PWM lookup table for mach-hmt
ARM: S3C64XX: Use PWM lookup table for mach-crag6410
ARM: S3C64XX: Use PWM lookup table for smdk6410
...
This is quite a quiet release in terms of volume of patches but it
includes a couple of really nice core changes - the work Sascha has done
in particular is something I've wanted to get done for a long time but
just never got round to myself. Highlights include:
- Support from Sascha Hauer for setting the voltage of parent supplies
based on requests from their children. This is used both to allow
set_voltage() to work through a dumb switch and to improve the
efficiency of systems where DCDCs are used to supply LDOs by minimising
the voltage drop over the LDOs.
- Removal of regulator_list by Tomeu Vizoso, meaning we're not
duplicating the device list maintained by the driver core.
- Support for Wolfson/Cirrus WM8998 and WM1818.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOez1AAoJECTWi3JdVIfQZSoH/jk2EQCG7hSIY6qVviHh+zQI
TWULXDnldyfT4eCYNAhwe/oQjFs7ngPXz9UpMAQwtWfWNoLBifF+Y5+X413nHY82
pKoRd+DQ1sIzGZb2YB0kS22Zg49Jilgv3y2Cw0aZuL7aqq7CEUGN3itEeWxqW9j8
a1ORD4d2zgki4gK9fUBTiur/dIhMn+8Gi4CmBvujsSCQR4Z5UNOjiodTU0NONiBX
znejoAoLJXzAyAoWN+p6sEvi9Gpx4QTV6tBOo56WPlzBgTX2qOFhhmJiQQ1rIJOv
MucgNn+cocarWfMyQwvqa0CL4ufjJm2DcYoIhfc2jZip/mAeqcbxpj5bxWzaLec=
=CX2S
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This is quite a quiet release in terms of volume of patches but it
includes a couple of really nice core changes - the work Sascha has
done in particular is something I've wanted to get done for a long
time but just never got round to myself.
Highlights include:
- Support from Sascha Hauer for setting the voltage of parent
supplies based on requests from their children. This is used both
to allow set_voltage() to work through a dumb switch and to improve
the efficiency of systems where DCDCs are used to supply LDOs by
minimising the voltage drop over the LDOs.
- Removal of regulator_list by Tomeu Vizoso, meaning we're not
duplicating the device list maintained by the driver core.
- Support for Wolfson/Cirrus WM8998 and WM1818"
* tag 'regulator-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (29 commits)
regulator: Use regulator_lock_supply() for get_voltage() too
regulator: arizona: Add regulator specific device tree binding document
regulator: stw481x: compile on COMPILE_TEST
regulator: qcom-smd: Correct set_load() unit
regulator: core: Propagate voltage changes to supply regulators
regulator: core: Factor out regulator_map_voltage
regulator: i.MX anatop: Allow supply regulator
regulator: introduce min_dropout_uV
regulator: core: create unlocked version of regulator_set_voltage
regulator: arizona-ldo1: Fix handling of GPIO 0
regulator: da9053: Update regulator for DA9053 BC silicon support
regulator: max77802: Separate sections for nodes and properties
regulator: max77802: Add input supply properties to DT binding doc
regulator: axp20x: set supply names for AXP22X DC1SW/DC5LDO internally
regulator: axp20x: Drop AXP221 DC1SW and DC5LDO regulator supplies from bindings
mfd: tps6105x: Use i2c regmap to access registers
regulator: act8865: add DT binding for property "active-semi,vsel-high"
regulator: act8865: support output voltage by VSET2[] bits
regulator: arizona: add support for WM8998 and WM1814
regulator: core: create unlocked version of regulator_list_voltage
...
The WRSTBI bit (disabled by default but enabled by bootloader), when
set, is responsible for resetting voltages to default values of
certain bucks on falling edge of Warm Reset Input pin from AP.
However on some boards (with S2MPS13) the pin is pulled down so any
suspend will effectively trigger the reset of bucks supplying the power
to the little and big cores. In the same time when resuming, these bucks
must provide voltage greater or equal to voltage before suspend to match
the frequency chosen by cpufreq. If voltage (default value of voltage
after reset) is lower than one set by cpufreq before suspend, then
system will hang during resuming.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
rts522a(rts5227s) is derived from rts5227, and mainly same with rts5227.
Add it to file mfd/rts5227.c to support this chip.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Definitions for GPIO registers 8, 9, 10, 11, 12 and 13 are added into
the register header file.
- DA9052_GPIO_8_9_REG 25
- DA9052_GPIO_10_11_REG 26
- DA9052_GPIO_12_13_REG 27
A modification is also made to the MFD core code to define these registers
as readable and writable. The functions for da9052_reg_readable() and
da9052_reg_writeable() have had their case statements altered to include
these new registers.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add MFD core driver for Intel Broxton Whiskey Cove PMIC,
which is specially accessed by hardware IPC, not a generic
I2C device
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
IRQ control registers of Intel Broxton Whisky Cove PMIC are
separated in two parts, so add secondary IRQ chip.
And the new member of device will be used in PMC IPC regmap APIs.
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some Arizona devices have a hardware ANC block present. This patch adds
the registers necessary to configure this hardware block.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On Odroid XU3 board (with S2MPS11 PMIC) the PWRHOLD bit in CTRL1
register must be manually set to 0 before initiating power off sequence.
One of usual power down methods for Exynos based devices looks like:
1. PWRHOLD pin of PMIC is connected to PSHOLD of Exynos SoC.
2. Exynos holds up this pin during system operation.
3. ACOKB pin of PMIC is pulled up to VBATT and optionally to pin in
other device.
4. When PWRHOLD/PSHOLD goes low, the PMIC will turn off the power if
ACOKB goes high.
On Odroid XU3 family the difference is in (3) - the ACOKB is grounded.
This means that PMIC must manually set PWRHOLD field to low and then
wait for signal from Application Processor (the usual change in
PWRHOLD/PSHOLD pin will actually cut off the power).
The patch adds respective binding allowing Odroid XU3 device to be
powered off.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reported-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add chip identification support for 88PM860 device
to the pm80x_chip_mapping table.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is at least one board on the market, i.e. Intel Galileo Gen2, that uses
_ADR to distinguish the devices under one actual device. Due to this we have to
improve the quirk in the MFD core to handle that board.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
