Currently DL aggregation is supported in RNDIS driver and is set to
3 by default. And there is no support to change downlink maximum
packets per transfer at runtime through module parameter. Hence add
module parameter for DL maximum packets per transfer to change it at
runtime.
echo 6 > /sys/module/g_android/parameters/rndis_dl_max_pkt_per_xfer
To disable DL aggregation during runtime,
echo 1 > /sys/module/g_android/parameters/rndis_dl_max_pkt_per_xfer
Change-Id: I3a1d0bc97358e2b6f233df7ae8725fb507de50db
Signed-off-by: Xerox Lin <xerox_lin@htc.com>
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
This change adds module param which allows to disable RNDIS
Multi-packet Feature (Aggregation support in Downlink path)
as this feature is enabled by default.
To disable use this param before moving to RNDIS Composition:
echo 1 > /sys/module/g_android/parameters/rndis_multipacket_dl_disable
Also counts errors as Rx errors if received RNDIS packets are
not following RNDIS message format as those packets are being
discarded.
Change-Id: I764430da78f2204af92e14bb279c11b24c7e4c67
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Add data aggregation support using RNDIS Multi Packet feature
to achieve better UDP Downlink throughput. Max 3 RNDIS Packets
aggregated into one RNDIS Packet with this implementation.
With this change, seeing UDP Downlink throughput increase
from 90 Mbps to above 100 Mbps when using Iperf and sending
data more than 100 Mbps.
Change-Id: I21c39482718944bb1b1068bdd02f626531e58f08
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Rajkumar Raghupathy <raghup@codeaurora.org>
For dual speed gadget, with current no. of request(10), there is
possibility of corner case occurence where all 10 reuqests are queued
to HW without setting IOC bit, which could lead to data stall in
RNDIS tethering and RNDIS local networking.
With this patch, counter will be incremented before queueing request to
HW and sets IOC bit for every nth request due to which the corner case
of all requests queued to HW without IOC bit set will be avoided.
Change-Id: I26515bfd9bbc8f7af38be7835692143f7093118a
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
On windows 7 platform, previously allocated ip address is maintained.
However, Host MAC address of 'usb0' interface is changed when the
tethering driver re-enumerated. Thus, the tethering network driver
can't be allocated ip address from dhcp. It causes connection delay
between host and phone for usb tethering.
This patch prevents from changing Host MAC address of 'usb0' interface.
In other words, this patch maintains the Host MAC address allocated when
first tethering driver although the driver is re-enumerated. However,
after reboot, the Host MAC address can be changed.
Change-Id: I43add9925e9d6d90c56cffbd3ed999104448f818
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
u_ether driver passes rx data to network layer and resubmits the
request back to usb hardware in interrupt context. Network layer
processes rx data by scheduling tasklet. For high throughput
scenarios on rx data path driver is spending lot of time in interrupt
context due to rx data processing by tasklet and continuous completion
and re-submission of the usb requests which results in watchdog bark.
Hence move the rx data processing and usb request submission to a
workqueue bottom half handler.
Change-Id: I316de8e267997137ac189a8b7b2846fa325f4a5a
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
RNDIS protocol supports data aggregation on uplink and can help
reduce mips by reducing number of interrupts on device. Throughput
also improved by 20-30%. Aggregation is disabled by setting
aggregation packet size to 1. To help better UL throughput, set
as ul aggregation support to 3 rndis packets by default. It can be
configured via module parameter: rndis_ul_max_pkt_per_xfer.
Change-Id: I0b62a21a5c3ceb6b04933d0d6da33301dbafe493
Signed-off-by: Vamsi Krishna <vskrishn@codeaurora.org>
Signed-off-by: Xerox Lin <xerox_lin@htc.com>
When rndis data transfer is in progress, some Windows7 Host PC is not
sending the GET_ENCAPSULATED_RESPONSE command for receiving the response
for the previous SEND_ENCAPSULATED_COMMAND processed.
The rndis function driver appends each response for the
SEND_ENCAPSULATED_COMMAND in a queue. As the above process got corrupted,
the Host sends a REMOTE_NDIS_RESET_MSG command to do a soft-reset.
As the rndis response queue is not freed, the previous response is sent
as a part of this REMOTE_NDIS_RESET_MSG's reset response and the Host
blocks any more Rndis transfers.
Hence free the rndis response queue as a part of this soft-reset so that
the current response for REMOTE_NDIS_RESET_MSG is sent properly during the
response command.
Change-Id: I8eff3849db452fe01b7d1fe4140ef1f1ad3f4fd4
Signed-off-by: Rajkumar Raghupathy <raghup@codeaurora.org>
Signed-off-by: Xerox Lin <xerox_lin@htc.com>
Fixed Android Issue #56549.
When both Vendor Class and Audio Class are activated for AOA 2.0,
the baInterfaceNr of the AudioControl Interface Descriptor points
to wrong interface numbers. They should be pointing to
Audio Control Device and Audio Streaming interfaces.
Replaced baInterfaceNr with the correct value.
Change-Id: Iaa083f3d97c1f0fc9481bf87852b2b51278a6351
Signed-off-by: Anson Jacob <ansonkuzhumbil@gmail.com>
Re-applying from
eb4c9d2db8
Most USB-AUDIO devices are limited to 256 byte for max iso buffer size.
If a IN_EP_MAX_PACKET_SIZE is bigger than a USB-AUDIO device's max iso
buffer size, it will cause noise. This patch will prevent this case as
possibe by reducing packet size. When using 44.1khz, 2ch, 16bit audio
data, if max packet size is bigger than 176 bytes, it's no problem.
Credits to: Iliyan Malchev <malchev@google.com>
Change-Id: Ic2a1c19ea65d5fb42bf12926b51b255b465d7215
Signed-off-by: Anson Jacob <ansonkuzhumbil@gmail.com>
Accessory connected to Android Device requires
Zero Length Packet (ZLP) to be written when data
transferred out from the Android device are multiples
of wMaxPacketSize (64bytes (Full-Speed) / 512bytes (High-Speed))
to end the transfer.
Change-Id: Ib2c2c0ab98ef9afa10e74a720142deca5c0ed476
Signed-off-by: Anson Jacob <ansonkuzhumbil@gmail.com>
- In the current implementation, when a signal is sent to the reading process,
read is cancelled by calling usb_ep_dequeue, which lead into calling
acc_complete_out with ECONNRESET, but the current logic treats it as
disconnection, which makes the device inaccessible until cable is actually
disconnected.
- The fix calls disconnect only when ESHUTDOWN error is passed.
- If data has already arrived while trying cancelling, the data is marked
as available, and it will be read out on the next read. This is necessary
as USB bulk is assumed to guarantee no data loss.
Signed-off-by: keunyoung <keunyoung@google.com>
Move the most of linux/usb/f_mtp.h header to uapi. Move the only
remaining structure definition into f_mtp.c, the only place that
uses it.
Change-Id: I952c1a9dc15c36bf295a0eb4d74b6b1ad912ed03
Signed-off-by: Colin Cross <ccross@android.com>
Make sure the android0 device is removed before we can destroy
the class.
Change-Id: Id584888c407beb80a1df4990f73fe31ccb9d4767
Signed-off-by: Benoit Goby <benoit@android.com>
Android MTP gadget uses 3 endpoints which are 1 in endpoint,
1 out endpoint, and 1 interrupt endpoint. However when MTP
gadget creates its endpoints, it creates the out endpoint twice
and overwrites the first created out endpoint with the second one,
so that it causes a leak of endpoint resources.
Change-Id: Iba82950095610b26b362f4b10a67cedfb1fee366
Signed-off-by: Peter Oh <poh@broadcom.com>
Reviewed-on: http://mps-gerrit.broadcom.com/37744
Reviewed-by: Graham Williams <gwilli@broadcom.com>
Reviewed-by: John Garry <jgarry@broadcom.com>
Branch-Open: Branch Status <branch_status_noreply@broadcom.com>
Reviewed-by: Checkpatch Status <checkpatch_status_noreply@broadcom.com>
Reviewed-by: Joyjit Nath <joyjit@broadcom.com>
Tested-by: AutoSubmit Status <autosubmit_status_noreply@broadcom.com>
The Android gadget driver disconnects the gadget on bind
and expects the gadget to stay disconnected until it calls
usb_gadget_connect when userspace is ready. Removed the call
to usb_gadget_connect in usb_gadget_probe_driver to avoid
enabling the pullup before userspace is ready.
Change-Id: I63707ac6e16a44eca52351a4bf80407d25fbd35e
Signed-off-by: Benoit Goby <benoit@android.com>
create_bulk_endpoints should not be __init since it is called when
accessory is enabled.
Change-Id: Iac6e9f29d53c93760e926efd8e7603432632acb4
Signed-off-by: Todd Poynor <toddpoynor@google.com>
ffs_func_eps_enable always take the highspeed usb_endpoint_descriptor
if it is available. Choose the correct usb_endpoint_descriptor
depending on the gadget speed instead.
Change-Id: I5b8444cfdf1b6fe1eef25525fb7a0a0f617a353e
Signed-off-by: Benoit Goby <benoit@android.com>
This driver presents a standard USB audio class interface to the host
and an ALSA PCM device to userspace
Change-Id: If16b14a5ff27045f9cb2daaf1ae9195c5eeab7d0
Signed-off-by: Mike Lockwood <lockwood@google.com>
The control request will be used by the host to enable/disable USB audio
and the ioctl will be used by userspace to read the audio mode
Change-Id: I81c38611b588451e80eacdccc417ca6e11c60cab
Signed-off-by: Mike Lockwood <lockwood@google.com>
Don't reset next_string_id every time the gadget is enabled, this makes
the next strings allocated overwrite strings allocated at probe time.
Instead, fix rndis not to allocate new string ids on every config bind.
Change-Id: Ied28ee416bb6f00c434c34176fe5b7f0dcb2b2d4
Signed-off-by: Benoit Goby <benoit@android.com>
create_bulk_endpoints should not be __init since it is called when
accessory is enabled
Change-Id: If827a4531f0f6c15af938345163923186368e2a5
Signed-off-by: Benoit Goby <benoit@android.com>
Add support for FunctionFS (ffs) to implement usb functions in userspace.
The aliases property stores the list of functions that are implemented
using functionfs.
For example:
echo "adb,mtp" > /sys/class/android_usb/android0/f_ffs/aliases
Then when the function are enabled:
echo "adb,acm" > /sys/class/android_usb/android0/functions
Internally, ffs and acm will be used.
Change-Id: I44117b183d48a5a99ddbee3ef2cf8998be74598e
Signed-off-by: Benoit Goby <benoit@android.com>
Product names may contain spaces and scanf %s only matches the 1st word.
Use strlcpy instead.
Change-Id: Ie8703fea9775f7fc17fe615a42597ca3816d36b0
Signed-off-by: Benoit Goby <benoit@android.com>
Remove the config from the configs list before releasing the spinlock.
Otherwise the other cpu might be processing a SET_CONFIGURATION that
will switch to the configuration that is being released.
Change-Id: Id4da0d0e18ead63e20cb236cd1d3e8e6d116acce
Signed-off-by: Benoit Goby <benoit@android.com>
When adb is enabled, only connect the gadget when adbd is ready. If adbd
dies or is restarted (e.g. "adb root"), the gadget is disconnected when
the adb device is close, and it is re-connected once adb re-open the
device.
- Add callbacks to adb, similar to FunctionFs callbacks, to notify the
gadget when the daemon is ready or closed.
- Refcount calls to android_enable/android_disable to enable the gadget
only once all the function daemons are ready.
- Add enable/disble to android_usb_function to notify the function when
it is added/removed from the list of enabled functions.
Change-Id: Id54ff85aec9cf8715c94b4f9bd6137a79ad58bfc
Signed-off-by: Benoit Goby <benoit@android.com>
When an ep_out req is dequeued because of userspace freezing,
don't set the error flag.
Change-Id: I680f1a1059b8ac2244aaa069e7d42dc44abf98e9
Signed-off-by: Colin Cross <ccross@android.com>
wait_event_interruptible in adb_read might return -ERESTARTSYS if
userspace is frozen during adb_read or another signal is delivered
to adb. If so, don't set dev->error to avoid resetting the adb
connection.
Change-Id: I5a7baa013a9a3a3b5305de7e6a0d18546a560018
Signed-off-by: Colin Cross <ccross@android.com>
USB accessory mode allows users to connect USB host hardware
specifically designed for Android-powered devices. The accessories
must adhere to the Android accessory protocol outlined in the
http://accessories.android.com documentation. This allows
Android devices that cannot act as a USB host to still interact with
USB hardware. When an Android device is in USB accessory mode, the
attached Android USB accessory acts as the host, provides power
to the USB bus, and enumerates connected devices.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Android Debug Bridge (adb) is a command line tool that lets
users communicate with a Android-powered device. It is used
mainly to debug applications and tranfer files. f_adb implements
the transport layer between the ADB Server (on the host) and the
ADBD daemon (on the device).
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB gadget function driver used by the Android framework to
implement the MTP and PTP protocols. It creates a character device
that provides an interface for fast transfer of files and
supports transferring files greater than 4GB.
Signed-off-by: Mike Lockwood <lockwood@android.com>
The Android Gadget driver is a composite driver that allows
userspace to change at runtime the list of functions enabled in
its configuration and to configure these functions. It supports
multiple functions: acm, adb, rndis, mtp/ptp, mass storage and
accessory.
It is usually controlled by a daemon that changes the configuration
based on user settings. For example, rndis is enabled when the user
enables sharing the phone data connection and adb (Android Debug
Bridge) is only enabled when the user wants to debug applications
for security reasons.
As an example on how to use it, the following shell commands will
make the gadget disconnect from the host and make it be re-enumerated
as a composite with 1 rndis and 2 acm interfaces, and a different
product id:
echo 0 > /sys/class/android_usb/android0/enable
echo rndis,acm > /sys/class/android_usb/android0/functions
echo 2 > /sys/class/android_usb/android0/f_acm/instances
echo 2d01 > /sys/class/android_usb/android0/idProduct
echo 1 > /sys/class/android_usb/android0/enable
The driver requires a gadget controller that supports software
control of the D+ pullup and the controller driver must support
disabling the pullup during composite_bind.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Signed-off-by: Benoit Goby <benoit@android.com>
Add product id for Abbott strip port cable for Precision meter which
uses the TI 3410 chip.
Signed-off-by: Anders Hammarquist <iko@iko.pp.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous text confused users by not describing the very common
(e.g. x86 PC) sitations where no PHY driver is necessary.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Re-enable chipidea irq even if there's no role changing to do. This is
a problem since b183c19f ("USB: chipidea: re-order irq handling to avoid
unhandled irqs"); when it manifests, chipidea irq gets disabled for good.
Cc: stable@vger.kernel.org # v3.7
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since usb phy code does return ERR_PTR() values, make sure that we don't
end up dereferencing them. This is a problem, for example, on platforms
that don't register a phy for chipidea since b7fa5c2a ("usb: phy: return
-ENXIO when PHY layer isn't enabled").
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use uninitialised termios data to determine when to configure the
device at open.
This also prevents stack data from leaking to userspace in the OOM error
path.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
