forge/linux-pinenote
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity Actions
linux-pinenote/drivers/scsi/eata_generic.h
Richard Knutsson 5f9279f239 [SCSI] eata_pio: Remove FALSE/TRUE defines 
eata_generic.h is only included by eata_pio.c and it only uses
FALSE/TRUE in comments.

Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-03-20 11:27:03 -05:00

400 lines
15 KiB
C
Raw Blame History

/********************************************************
* Header file for eata_dma.c and eata_pio.c *
* Linux EATA SCSI drivers *
* (c) 1993-96 Michael Neuffer *
* mike@i-Connect.Net *
* neuffer@mail.uni-mainz.de *
*********************************************************
* last change: 96/08/14 *
********************************************************/
#ifndef _EATA_GENERIC_H
#define _EATA_GENERIC_H
/*********************************************
* Misc. definitions *
*********************************************/
#define R_LIMIT 0x20000
#define MAXISA 4
#define MAXEISA 16
#define MAXPCI 16
#define MAXIRQ 16
#define MAXTARGET 16
#define MAXCHANNEL 3
#define IS_ISA 'I'
#define IS_EISA 'E'
#define IS_PCI 'P'
#define BROKEN_INQUIRY 1
#define BUSMASTER 0xff
#define PIO 0xfe
#define EATA_SIGNATURE 0x45415441 /* BIG ENDIAN coded "EATA" sig. */
#define DPT_ID1 0x12
#define DPT_ID2 0x14
#define ATT_ID1 0x06
#define ATT_ID2 0x94
#define ATT_ID3 0x0
#define NEC_ID1 0x38
#define NEC_ID2 0xa3
#define NEC_ID3 0x82
#define EATA_CP_SIZE 44
#define MAX_PCI_DEVICES 32 /* Maximum # Of Devices Per Bus */
#define MAX_METHOD_2 16 /* Max Devices For Method 2 */
#define MAX_PCI_BUS 16 /* Maximum # Of Busses Allowed */
#define SG_SIZE 64
#define SG_SIZE_BIG 252 /* max. 8096 elements, 64k */
#define UPPER_DEVICE_QUEUE_LIMIT 64 /* The limit we have to set for the
* device queue to keep the broken
* midlevel SCSI code from producing
* bogus timeouts
*/
#define TYPE_DISK_QUEUE 16
#define TYPE_TAPE_QUEUE 4
#define TYPE_ROM_QUEUE 4
#define TYPE_OTHER_QUEUE 2
#define FREE 0
#define OK 0
#define NO_TIMEOUT 0
#define USED 1
#define TIMEOUT 2
#define RESET 4
#define LOCKED 8
#define ABORTED 16
#define READ 0
#define WRITE 1
#define OTHER 2
#define HD(cmd) ((hostdata *)&(cmd->device->host->hostdata))
#define CD(cmd) ((struct eata_ccb *)(cmd->host_scribble))
#define SD(host) ((hostdata *)&(host->hostdata))
/***********************************************
* EATA Command & Register definitions *
***********************************************/
#define PCI_REG_DPTconfig 0x40
#define PCI_REG_PumpModeAddress 0x44
#define PCI_REG_PumpModeData 0x48
#define PCI_REG_ConfigParam1 0x50
#define PCI_REG_ConfigParam2 0x54
#define EATA_CMD_PIO_SETUPTEST 0xc6
#define EATA_CMD_PIO_READ_CONFIG 0xf0
#define EATA_CMD_PIO_SET_CONFIG 0xf1
#define EATA_CMD_PIO_SEND_CP 0xf2
#define EATA_CMD_PIO_RECEIVE_SP 0xf3
#define EATA_CMD_PIO_TRUNC 0xf4
#define EATA_CMD_RESET 0xf9
#define EATA_CMD_IMMEDIATE 0xfa
#define EATA_CMD_DMA_READ_CONFIG 0xfd
#define EATA_CMD_DMA_SET_CONFIG 0xfe
#define EATA_CMD_DMA_SEND_CP 0xff
#define ECS_EMULATE_SENSE 0xd4
#define EATA_GENERIC_ABORT 0x00
#define EATA_SPECIFIC_RESET 0x01
#define EATA_BUS_RESET 0x02
#define EATA_SPECIFIC_ABORT 0x03
#define EATA_QUIET_INTR 0x04
#define EATA_COLD_BOOT_HBA 0x06 /* Only as a last resort */
#define EATA_FORCE_IO 0x07
#define HA_CTRLREG 0x206 /* control register for HBA */
#define HA_CTRL_DISINT 0x02 /* CTRLREG: disable interrupts */
#define HA_CTRL_RESCPU 0x04 /* CTRLREG: reset processor */
#define HA_CTRL_8HEADS 0x08 /* CTRLREG: set for drives with*
* >=8 heads (WD1003 rudimentary :-) */
#define HA_WCOMMAND 0x07 /* command register offset */
#define HA_WIFC 0x06 /* immediate command offset */
#define HA_WCODE 0x05
#define HA_WCODE2 0x04
#define HA_WDMAADDR 0x02 /* DMA address LSB offset */
#define HA_RAUXSTAT 0x08 /* aux status register offset*/
#define HA_RSTATUS 0x07 /* status register offset */
#define HA_RDATA 0x00 /* data register (16bit) */
#define HA_WDATA 0x00 /* data register (16bit) */
#define HA_ABUSY 0x01 /* aux busy bit */
#define HA_AIRQ 0x02 /* aux IRQ pending bit */
#define HA_SERROR 0x01 /* pr. command ended in error*/
#define HA_SMORE 0x02 /* more data soon to come */
#define HA_SCORR 0x04 /* data corrected */
#define HA_SDRQ 0x08 /* data request active */
#define HA_SSC 0x10 /* seek complete */
#define HA_SFAULT 0x20 /* write fault */
#define HA_SREADY 0x40 /* drive ready */
#define HA_SBUSY 0x80 /* drive busy */
#define HA_SDRDY HA_SSC+HA_SREADY+HA_SDRQ
/**********************************************
* Message definitions *
**********************************************/
#define HA_NO_ERROR 0x00 /* No Error */
#define HA_ERR_SEL_TO 0x01 /* Selection Timeout */
#define HA_ERR_CMD_TO 0x02 /* Command Timeout */
#define HA_BUS_RESET 0x03 /* SCSI Bus Reset Received */
#define HA_INIT_POWERUP 0x04 /* Initial Controller Power-up */
#define HA_UNX_BUSPHASE 0x05 /* Unexpected Bus Phase */
#define HA_UNX_BUS_FREE 0x06 /* Unexpected Bus Free */
#define HA_BUS_PARITY 0x07 /* Bus Parity Error */
#define HA_SCSI_HUNG 0x08 /* SCSI Hung */
#define HA_UNX_MSGRJCT 0x09 /* Unexpected Message Rejected */
#define HA_RESET_STUCK 0x0a /* SCSI Bus Reset Stuck */
#define HA_RSENSE_FAIL 0x0b /* Auto Request-Sense Failed */
#define HA_PARITY_ERR 0x0c /* Controller Ram Parity Error */
#define HA_CP_ABORT_NA 0x0d /* Abort Message sent to non-active cmd */
#define HA_CP_ABORTED 0x0e /* Abort Message sent to active cmd */
#define HA_CP_RESET_NA 0x0f /* Reset Message sent to non-active cmd */
#define HA_CP_RESET 0x10 /* Reset Message sent to active cmd */
#define HA_ECC_ERR 0x11 /* Controller Ram ECC Error */
#define HA_PCI_PARITY 0x12 /* PCI Parity Error */
#define HA_PCI_MABORT 0x13 /* PCI Master Abort */
#define HA_PCI_TABORT 0x14 /* PCI Target Abort */
#define HA_PCI_STABORT 0x15 /* PCI Signaled Target Abort */
/**********************************************
* Other definitions *
**********************************************/
struct reg_bit { /* reading this one will clear the interrupt */
__u8 error:1; /* previous command ended in an error */
__u8 more:1; /* more DATA coming soon, poll BSY & DRQ (PIO) */
__u8 corr:1; /* data read was successfully corrected with ECC*/
__u8 drq:1; /* data request active */
__u8 sc:1; /* seek complete */
__u8 fault:1; /* write fault */
__u8 ready:1; /* drive ready */
__u8 busy:1; /* controller busy */
};
struct reg_abit { /* reading this won't clear the interrupt */
__u8 abusy:1; /* auxiliary busy */
__u8 irq:1; /* set when drive interrupt is asserted */
__u8 dummy:6;
};
struct eata_register { /* EATA register set */
__u8 data_reg[2]; /* R, couldn't figure this one out */
__u8 cp_addr[4]; /* W, CP address register */
union {
__u8 command; /* W, command code: [read|set] conf, send CP*/
struct reg_bit status; /* R, see register_bit1 */
__u8 statusbyte;
} ovr;
struct reg_abit aux_stat; /* R, see register_bit2 */
};
struct get_conf { /* Read Configuration Array */
__u32 len; /* Should return 0x22, 0x24, etc */
__u32 signature; /* Signature MUST be "EATA" */
__u8 version2:4,
version:4; /* EATA Version level */
__u8 OCS_enabled:1, /* Overlap Command Support enabled */
TAR_support:1, /* SCSI Target Mode supported */
TRNXFR:1, /* Truncate Transfer Cmd not necessary *
* Only used in PIO Mode */
MORE_support:1, /* MORE supported (only PIO Mode) */
DMA_support:1, /* DMA supported Driver uses only *
* this mode */
DMA_valid:1, /* DRQ value in Byte 30 is valid */
ATA:1, /* ATA device connected (not supported) */
HAA_valid:1; /* Hostadapter Address is valid */
__u16 cppadlen; /* Number of pad bytes send after CD data *
* set to zero for DMA commands */
__u8 scsi_id[4]; /* SCSI ID of controller 2-0 Byte 0 res. *
* if not, zero is returned */
__u32 cplen; /* CP length: number of valid cp bytes */
__u32 splen; /* Number of bytes returned after *
* Receive SP command */
__u16 queuesiz; /* max number of queueable CPs */
__u16 dummy;
__u16 SGsiz; /* max number of SG table entries */
__u8 IRQ:4, /* IRQ used this HA */
IRQ_TR:1, /* IRQ Trigger: 0=edge, 1=level */
SECOND:1, /* This is a secondary controller */
DMA_channel:2; /* DRQ index, DRQ is 2comp of DRQX */
__u8 sync; /* device at ID 7 tru 0 is running in *
* synchronous mode, this will disappear */
__u8 DSBLE:1, /* ISA i/o addressing is disabled */
FORCADR:1, /* i/o address has been forced */
SG_64K:1,
SG_UAE:1,
:4;
__u8 MAX_ID:5, /* Max number of SCSI target IDs */
MAX_CHAN:3; /* Number of SCSI busses on HBA */
__u8 MAX_LUN; /* Max number of LUNs */
__u8 :3,
AUTOTRM:1,
M1_inst:1,
ID_qest:1, /* Raidnum ID is questionable */
is_PCI:1, /* HBA is PCI */
is_EISA:1; /* HBA is EISA */
__u8 RAIDNUM; /* unique HBA identifier */
__u8 unused[474];
};
struct eata_sg_list
{
__u32 data;
__u32 len;
};
struct eata_ccb { /* Send Command Packet structure */
__u8 SCSI_Reset:1, /* Cause a SCSI Bus reset on the cmd */
HBA_Init:1, /* Cause Controller to reinitialize */
Auto_Req_Sen:1, /* Do Auto Request Sense on errors */
scatter:1, /* Data Ptr points to a SG Packet */
Resrvd:1, /* RFU */
Interpret:1, /* Interpret the SCSI cdb of own use */
DataOut:1, /* Data Out phase with command */
DataIn:1; /* Data In phase with command */
__u8 reqlen; /* Request Sense Length *
* Valid if Auto_Req_Sen=1 */
__u8 unused[3];
__u8 FWNEST:1, /* send cmd to phys RAID component */
unused2:7;
__u8 Phsunit:1, /* physical unit on mirrored pair */
I_AT:1, /* inhibit address translation */
I_HBA_C:1, /* HBA inhibit caching */
unused3:5;
__u8 cp_id:5, /* SCSI Device ID of target */
cp_channel:3; /* SCSI Channel # of HBA */
__u8 cp_lun:3,
:2,
cp_luntar:1, /* CP is for target ROUTINE */
cp_dispri:1, /* Grant disconnect privilege */
cp_identify:1; /* Always TRUE */
__u8 cp_msg1; /* Message bytes 0-3 */
__u8 cp_msg2;
__u8 cp_msg3;
__u8 cp_cdb[12]; /* Command Descriptor Block */
__u32 cp_datalen; /* Data Transfer Length *
* If scatter=1 len of sg package */
void *cp_viraddr; /* address of this ccb */
__u32 cp_dataDMA; /* Data Address, if scatter=1 *
* address of scatter packet */
__u32 cp_statDMA; /* address for Status Packet */
__u32 cp_reqDMA; /* Request Sense Address, used if *
* CP command ends with error */
/* Additional CP info begins here */
__u32 timestamp; /* Needed to measure command latency */
__u32 timeout;
__u8 sizeindex;
__u8 rw_latency;
__u8 retries;
__u8 status; /* status of this queueslot */
struct scsi_cmnd *cmd; /* address of cmd */
struct eata_sg_list *sg_list;
};
struct eata_sp {
__u8 hba_stat:7, /* HBA status */
EOC:1; /* True if command finished */
__u8 scsi_stat; /* Target SCSI status */
__u8 reserved[2];
__u32 residue_len; /* Number of bytes not transferred */
struct eata_ccb *ccb; /* Address set in COMMAND PACKET */
__u8 msg[12];
};
typedef struct hstd {
__u8 vendor[9];
__u8 name[18];
__u8 revision[6];
__u8 EATA_revision;
__u32 firmware_revision;
__u8 HBA_number;
__u8 bustype; /* bustype of HBA */
__u8 channel; /* # of avail. scsi channels */
__u8 state; /* state of HBA */
__u8 primary; /* true if primary */
__u8 more_support:1, /* HBA supports MORE flag */
immediate_support:1, /* HBA supports IMMEDIATE CMDs*/
broken_INQUIRY:1; /* This is an EISA HBA with *
* broken INQUIRY */
__u8 do_latency; /* Latency measurement flag */
__u32 reads[13];
__u32 writes[13];
__u32 reads_lat[12][4];
__u32 writes_lat[12][4];
__u32 all_lat[4];
__u8 resetlevel[MAXCHANNEL];
__u32 last_ccb; /* Last used ccb */
__u32 cplen; /* size of CP in words */
__u16 cppadlen; /* pad length of cp in words */
__u16 queuesize;
__u16 sgsize; /* # of entries in the SG list*/
__u16 devflags; /* bits set for detected devices */
__u8 hostid; /* SCSI ID of HBA */
__u8 moresupport; /* HBA supports MORE flag */
struct Scsi_Host *next;
struct Scsi_Host *prev;
struct pci_dev *pdev; /* PCI device or NULL for non PCI */
struct eata_sp sp; /* status packet */
struct eata_ccb ccb[0]; /* ccb array begins here */
}hostdata;
/* structure for max. 2 emulated drives */
struct drive_geom_emul {
__u8 trans; /* translation flag 1=transl */
__u8 channel; /* SCSI channel number */
__u8 HBA; /* HBA number (prim/sec) */
__u8 id; /* drive id */
__u8 lun; /* drive lun */
__u32 heads; /* number of heads */
__u32 sectors; /* number of sectors */
__u32 cylinder; /* number of cylinders */
};
struct geom_emul {
__u8 bios_drives; /* number of emulated drives */
struct drive_geom_emul drv[2]; /* drive structures */
};
#endif /* _EATA_GENERIC_H */
/*
* Overrides for Emacs so that we almost follow Linus's tabbing style.
* Emacs will notice this stuff at the end of the file and automatically
* adjust the settings for this buffer only. This must remain at the end
* of the file.
* ---------------------------------------------------------------------------
* Local variables:
* c-indent-level: 4
* c-brace-imaginary-offset: 0
* c-brace-offset: -4
* c-argdecl-indent: 4
* c-label-offset: -4
* c-continued-statement-offset: 4
* c-continued-brace-offset: 0
* tab-width: 8
* End:
*/
Reference in a new issue View git blame Copy permalink