forge/linux-pinenote
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity Actions
linux-pinenote/arch/arm/mach-ixp4xx/ixdp425-setup.c
Linus Walleij 8040dd09c2 ARM: ixp4xx: convert remaining users to use gpiolib 
A few call sites inside mach-ixp4xx were still using the custom
ixp4xx GPIO API with gpio_line_* accessors, convert all these
to use the standard gpiolib functions instead. Also attempt to
request and label all GPIOs before use. Move the GPIO requests
to per-machine device_initcalls() so we are not dependent on the
GPIO chip to be available at machine_init time.

Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-09-27 14:15:07 +02:00

310 lines
7.3 KiB
C
Raw Blame History

/*
* arch/arm/mach-ixp4xx/ixdp425-setup.c
*
* IXDP425/IXCDP1100 board-setup
*
* Copyright (C) 2003-2005 MontaVista Software, Inc.
*
* Author: Deepak Saxena <dsaxena@plexity.net>
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/device.h>
#include <linux/serial.h>
#include <linux/tty.h>
#include <linux/serial_8250.h>
#include <linux/i2c-gpio.h>
#include <linux/io.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/delay.h>
#include <linux/gpio.h>
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#define IXDP425_SDA_PIN 7
#define IXDP425_SCL_PIN 6
/* NAND Flash pins */
#define IXDP425_NAND_NCE_PIN 12
#define IXDP425_NAND_CMD_BYTE 0x01
#define IXDP425_NAND_ADDR_BYTE 0x02
static struct flash_platform_data ixdp425_flash_data = {
.map_name = "cfi_probe",
.width = 2,
};
static struct resource ixdp425_flash_resource = {
.flags = IORESOURCE_MEM,
};
static struct platform_device ixdp425_flash = {
.name = "IXP4XX-Flash",
.id = 0,
.dev = {
.platform_data = &ixdp425_flash_data,
},
.num_resources = 1,
.resource = &ixdp425_flash_resource,
};
#if defined(CONFIG_MTD_NAND_PLATFORM) || \
defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
static struct mtd_partition ixdp425_partitions[] = {
{
.name = "ixp400 NAND FS 0",
.offset = 0,
.size = SZ_8M
}, {
.name = "ixp400 NAND FS 1",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL
},
};
static void
ixdp425_flash_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
{
struct nand_chip *this = mtd->priv;
int offset = (int)this->priv;
if (ctrl & NAND_CTRL_CHANGE) {
if (ctrl & NAND_NCE) {
gpio_set_value(IXDP425_NAND_NCE_PIN, 0);
udelay(5);
} else
gpio_set_value(IXDP425_NAND_NCE_PIN, 1);
offset = (ctrl & NAND_CLE) ? IXDP425_NAND_CMD_BYTE : 0;
offset |= (ctrl & NAND_ALE) ? IXDP425_NAND_ADDR_BYTE : 0;
this->priv = (void *)offset;
}
if (cmd != NAND_CMD_NONE)
writeb(cmd, this->IO_ADDR_W + offset);
}
static struct platform_nand_data ixdp425_flash_nand_data = {
.chip = {
.nr_chips = 1,
.chip_delay = 30,
.partitions = ixdp425_partitions,
.nr_partitions = ARRAY_SIZE(ixdp425_partitions),
},
.ctrl = {
.cmd_ctrl = ixdp425_flash_nand_cmd_ctrl
}
};
static struct resource ixdp425_flash_nand_resource = {
.flags = IORESOURCE_MEM,
};
static struct platform_device ixdp425_flash_nand = {
.name = "gen_nand",
.id = -1,
.dev = {
.platform_data = &ixdp425_flash_nand_data,
},
.num_resources = 1,
.resource = &ixdp425_flash_nand_resource,
};
#endif /* CONFIG_MTD_NAND_PLATFORM */
static struct i2c_gpio_platform_data ixdp425_i2c_gpio_data = {
.sda_pin = IXDP425_SDA_PIN,
.scl_pin = IXDP425_SCL_PIN,
};
static struct platform_device ixdp425_i2c_gpio = {
.name = "i2c-gpio",
.id = 0,
.dev = {
.platform_data = &ixdp425_i2c_gpio_data,
},
};
static struct resource ixdp425_uart_resources[] = {
{
.start = IXP4XX_UART1_BASE_PHYS,
.end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
.flags = IORESOURCE_MEM
},
{
.start = IXP4XX_UART2_BASE_PHYS,
.end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
.flags = IORESOURCE_MEM
}
};
static struct plat_serial8250_port ixdp425_uart_data[] = {
{
.mapbase = IXP4XX_UART1_BASE_PHYS,
.membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
.irq = IRQ_IXP4XX_UART1,
.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
.iotype = UPIO_MEM,
.regshift = 2,
.uartclk = IXP4XX_UART_XTAL,
},
{
.mapbase = IXP4XX_UART2_BASE_PHYS,
.membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
.irq = IRQ_IXP4XX_UART2,
.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
.iotype = UPIO_MEM,
.regshift = 2,
.uartclk = IXP4XX_UART_XTAL,
},
{ },
};
static struct platform_device ixdp425_uart = {
.name = "serial8250",
.id = PLAT8250_DEV_PLATFORM,
.dev.platform_data = ixdp425_uart_data,
.num_resources = 2,
.resource = ixdp425_uart_resources
};
/* Built-in 10/100 Ethernet MAC interfaces */
static struct eth_plat_info ixdp425_plat_eth[] = {
{
.phy = 0,
.rxq = 3,
.txreadyq = 20,
}, {
.phy = 1,
.rxq = 4,
.txreadyq = 21,
}
};
static struct platform_device ixdp425_eth[] = {
{
.name = "ixp4xx_eth",
.id = IXP4XX_ETH_NPEB,
.dev.platform_data = ixdp425_plat_eth,
}, {
.name = "ixp4xx_eth",
.id = IXP4XX_ETH_NPEC,
.dev.platform_data = ixdp425_plat_eth + 1,
}
};
static struct platform_device *ixdp425_devices[] __initdata = {
&ixdp425_i2c_gpio,
&ixdp425_flash,
#if defined(CONFIG_MTD_NAND_PLATFORM) || \
defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
&ixdp425_flash_nand,
#endif
&ixdp425_uart,
&ixdp425_eth[0],
&ixdp425_eth[1],
};
static void __init ixdp425_init(void)
{
ixp4xx_sys_init();
ixdp425_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
ixdp425_flash_resource.end =
IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
#if defined(CONFIG_MTD_NAND_PLATFORM) || \
defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
ixdp425_flash_nand_resource.start = IXP4XX_EXP_BUS_BASE(3),
ixdp425_flash_nand_resource.end = IXP4XX_EXP_BUS_BASE(3) + 0x10 - 1;
gpio_request(IXDP425_NAND_NCE_PIN, "NAND NCE pin");
gpio_direction_output(IXDP425_NAND_NCE_PIN, 0);
/* Configure expansion bus for NAND Flash */
*IXP4XX_EXP_CS3 = IXP4XX_EXP_BUS_CS_EN |
IXP4XX_EXP_BUS_STROBE_T(1) | /* extend by 1 clock */
IXP4XX_EXP_BUS_CYCLES(0) | /* Intel cycles */
IXP4XX_EXP_BUS_SIZE(0) | /* 512bytes addr space*/
IXP4XX_EXP_BUS_WR_EN |
IXP4XX_EXP_BUS_BYTE_EN; /* 8 bit data bus */
#endif
if (cpu_is_ixp43x()) {
ixdp425_uart.num_resources = 1;
ixdp425_uart_data[1].flags = 0;
}
platform_add_devices(ixdp425_devices, ARRAY_SIZE(ixdp425_devices));
}
#ifdef CONFIG_ARCH_IXDP425
MACHINE_START(IXDP425, "Intel IXDP425 Development Platform")
/* Maintainer: MontaVista Software, Inc. */
.map_io = ixp4xx_map_io,
.init_early = ixp4xx_init_early,
.init_irq = ixp4xx_init_irq,
.init_time = ixp4xx_timer_init,
.atag_offset = 0x100,
.init_machine = ixdp425_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
#endif
.restart = ixp4xx_restart,
MACHINE_END
#endif
#ifdef CONFIG_MACH_IXDP465
MACHINE_START(IXDP465, "Intel IXDP465 Development Platform")
/* Maintainer: MontaVista Software, Inc. */
.map_io = ixp4xx_map_io,
.init_early = ixp4xx_init_early,
.init_irq = ixp4xx_init_irq,
.init_time = ixp4xx_timer_init,
.atag_offset = 0x100,
.init_machine = ixdp425_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
#endif
MACHINE_END
#endif
#ifdef CONFIG_ARCH_PRPMC1100
MACHINE_START(IXCDP1100, "Intel IXCDP1100 Development Platform")
/* Maintainer: MontaVista Software, Inc. */
.map_io = ixp4xx_map_io,
.init_early = ixp4xx_init_early,
.init_irq = ixp4xx_init_irq,
.init_time = ixp4xx_timer_init,
.atag_offset = 0x100,
.init_machine = ixdp425_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
#endif
MACHINE_END
#endif
#ifdef CONFIG_MACH_KIXRP435
MACHINE_START(KIXRP435, "Intel KIXRP435 Reference Platform")
/* Maintainer: MontaVista Software, Inc. */
.map_io = ixp4xx_map_io,
.init_early = ixp4xx_init_early,
.init_irq = ixp4xx_init_irq,
.init_time = ixp4xx_timer_init,
.atag_offset = 0x100,
.init_machine = ixdp425_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
#endif
MACHINE_END
#endif
Reference in a new issue View git blame Copy permalink