d5e660ba80
There are no users of fallback_dev, so remove it. Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
110 lines
2.4 KiB
C
110 lines
2.4 KiB
C
/*
|
|
* Dynamic DMA mapping support.
|
|
*/
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/mm.h>
|
|
#include <linux/string.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/module.h>
|
|
#include <linux/dmar.h>
|
|
#include <asm/iommu.h>
|
|
#include <asm/machvec.h>
|
|
#include <linux/dma-mapping.h>
|
|
|
|
|
|
#ifdef CONFIG_INTEL_IOMMU
|
|
|
|
#include <linux/kernel.h>
|
|
|
|
#include <asm/page.h>
|
|
|
|
dma_addr_t bad_dma_address __read_mostly;
|
|
EXPORT_SYMBOL(bad_dma_address);
|
|
|
|
static int iommu_sac_force __read_mostly;
|
|
|
|
int no_iommu __read_mostly;
|
|
#ifdef CONFIG_IOMMU_DEBUG
|
|
int force_iommu __read_mostly = 1;
|
|
#else
|
|
int force_iommu __read_mostly;
|
|
#endif
|
|
|
|
int iommu_pass_through;
|
|
|
|
extern struct dma_map_ops intel_dma_ops;
|
|
|
|
static int __init pci_iommu_init(void)
|
|
{
|
|
if (iommu_detected)
|
|
intel_iommu_init();
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Must execute after PCI subsystem */
|
|
fs_initcall(pci_iommu_init);
|
|
|
|
void pci_iommu_shutdown(void)
|
|
{
|
|
return;
|
|
}
|
|
|
|
void __init
|
|
iommu_dma_init(void)
|
|
{
|
|
return;
|
|
}
|
|
|
|
int iommu_dma_supported(struct device *dev, u64 mask)
|
|
{
|
|
/* Copied from i386. Doesn't make much sense, because it will
|
|
only work for pci_alloc_coherent.
|
|
The caller just has to use GFP_DMA in this case. */
|
|
if (mask < DMA_BIT_MASK(24))
|
|
return 0;
|
|
|
|
/* Tell the device to use SAC when IOMMU force is on. This
|
|
allows the driver to use cheaper accesses in some cases.
|
|
|
|
Problem with this is that if we overflow the IOMMU area and
|
|
return DAC as fallback address the device may not handle it
|
|
correctly.
|
|
|
|
As a special case some controllers have a 39bit address
|
|
mode that is as efficient as 32bit (aic79xx). Don't force
|
|
SAC for these. Assume all masks <= 40 bits are of this
|
|
type. Normally this doesn't make any difference, but gives
|
|
more gentle handling of IOMMU overflow. */
|
|
if (iommu_sac_force && (mask >= DMA_BIT_MASK(40))) {
|
|
dev_info(dev, "Force SAC with mask %llx\n", mask);
|
|
return 0;
|
|
}
|
|
|
|
return 1;
|
|
}
|
|
EXPORT_SYMBOL(iommu_dma_supported);
|
|
|
|
void __init pci_iommu_alloc(void)
|
|
{
|
|
dma_ops = &intel_dma_ops;
|
|
|
|
dma_ops->sync_single_for_cpu = machvec_dma_sync_single;
|
|
dma_ops->sync_sg_for_cpu = machvec_dma_sync_sg;
|
|
dma_ops->sync_single_for_device = machvec_dma_sync_single;
|
|
dma_ops->sync_sg_for_device = machvec_dma_sync_sg;
|
|
dma_ops->dma_supported = iommu_dma_supported;
|
|
|
|
/*
|
|
* The order of these functions is important for
|
|
* fall-back/fail-over reasons
|
|
*/
|
|
detect_intel_iommu();
|
|
|
|
#ifdef CONFIG_SWIOTLB
|
|
pci_swiotlb_init();
|
|
#endif
|
|
}
|
|
|
|
#endif
|