c072b90c8d
This is the usual physical memory layout boot printout: ... [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00001000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] [ 0.000000] Normal [mem 0x100000000-0xc3fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00001000-0x00099fff] [ 0.000000] node 0: [mem 0x00100000-0xbf78ffff] [ 0.000000] node 0: [mem 0x100000000-0x63fffffff] [ 0.000000] node 1: [mem 0x640000000-0xc3fffffff] ... This is the log when we set "mem=2G" on the boot cmdline: ... [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00001000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] // should be 0x7fffffff, right? [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00001000-0x00099fff] [ 0.000000] node 0: [mem 0x00100000-0x7fffffff] ... This patch fixes the printout, the following log shows the right ranges: ... [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00001000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0x7fffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00001000-0x00099fff] [ 0.000000] node 0: [mem 0x00100000-0x7fffffff] ... Suggested-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Xishi Qiu <qiuxishi@huawei.com> Cc: Linux MM <linux-mm@kvack.org> Cc: <dave@sr71.net> Cc: Rik van Riel <riel@redhat.com> Link: http://lkml.kernel.org/r/5487AB3D.6070306@huawei.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
317 lines
9.6 KiB
C
317 lines
9.6 KiB
C
/*
|
|
* linux/include/asm/dma.h: Defines for using and allocating dma channels.
|
|
* Written by Hennus Bergman, 1992.
|
|
* High DMA channel support & info by Hannu Savolainen
|
|
* and John Boyd, Nov. 1992.
|
|
*/
|
|
|
|
#ifndef _ASM_X86_DMA_H
|
|
#define _ASM_X86_DMA_H
|
|
|
|
#include <linux/spinlock.h> /* And spinlocks */
|
|
#include <asm/io.h> /* need byte IO */
|
|
|
|
#ifdef HAVE_REALLY_SLOW_DMA_CONTROLLER
|
|
#define dma_outb outb_p
|
|
#else
|
|
#define dma_outb outb
|
|
#endif
|
|
|
|
#define dma_inb inb
|
|
|
|
/*
|
|
* NOTES about DMA transfers:
|
|
*
|
|
* controller 1: channels 0-3, byte operations, ports 00-1F
|
|
* controller 2: channels 4-7, word operations, ports C0-DF
|
|
*
|
|
* - ALL registers are 8 bits only, regardless of transfer size
|
|
* - channel 4 is not used - cascades 1 into 2.
|
|
* - channels 0-3 are byte - addresses/counts are for physical bytes
|
|
* - channels 5-7 are word - addresses/counts are for physical words
|
|
* - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries
|
|
* - transfer count loaded to registers is 1 less than actual count
|
|
* - controller 2 offsets are all even (2x offsets for controller 1)
|
|
* - page registers for 5-7 don't use data bit 0, represent 128K pages
|
|
* - page registers for 0-3 use bit 0, represent 64K pages
|
|
*
|
|
* DMA transfers are limited to the lower 16MB of _physical_ memory.
|
|
* Note that addresses loaded into registers must be _physical_ addresses,
|
|
* not logical addresses (which may differ if paging is active).
|
|
*
|
|
* Address mapping for channels 0-3:
|
|
*
|
|
* A23 ... A16 A15 ... A8 A7 ... A0 (Physical addresses)
|
|
* | ... | | ... | | ... |
|
|
* | ... | | ... | | ... |
|
|
* | ... | | ... | | ... |
|
|
* P7 ... P0 A7 ... A0 A7 ... A0
|
|
* | Page | Addr MSB | Addr LSB | (DMA registers)
|
|
*
|
|
* Address mapping for channels 5-7:
|
|
*
|
|
* A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0 (Physical addresses)
|
|
* | ... | \ \ ... \ \ \ ... \ \
|
|
* | ... | \ \ ... \ \ \ ... \ (not used)
|
|
* | ... | \ \ ... \ \ \ ... \
|
|
* P7 ... P1 (0) A7 A6 ... A0 A7 A6 ... A0
|
|
* | Page | Addr MSB | Addr LSB | (DMA registers)
|
|
*
|
|
* Again, channels 5-7 transfer _physical_ words (16 bits), so addresses
|
|
* and counts _must_ be word-aligned (the lowest address bit is _ignored_ at
|
|
* the hardware level, so odd-byte transfers aren't possible).
|
|
*
|
|
* Transfer count (_not # bytes_) is limited to 64K, represented as actual
|
|
* count - 1 : 64K => 0xFFFF, 1 => 0x0000. Thus, count is always 1 or more,
|
|
* and up to 128K bytes may be transferred on channels 5-7 in one operation.
|
|
*
|
|
*/
|
|
|
|
#define MAX_DMA_CHANNELS 8
|
|
|
|
/* 16MB ISA DMA zone */
|
|
#define MAX_DMA_PFN ((16UL * 1024 * 1024) >> PAGE_SHIFT)
|
|
|
|
/* 4GB broken PCI/AGP hardware bus master zone */
|
|
#define MAX_DMA32_PFN ((4UL * 1024 * 1024 * 1024) >> PAGE_SHIFT)
|
|
|
|
#ifdef CONFIG_X86_32
|
|
/* The maximum address that we can perform a DMA transfer to on this platform */
|
|
#define MAX_DMA_ADDRESS (PAGE_OFFSET + 0x1000000)
|
|
#else
|
|
/* Compat define for old dma zone */
|
|
#define MAX_DMA_ADDRESS ((unsigned long)__va(MAX_DMA_PFN << PAGE_SHIFT))
|
|
#endif
|
|
|
|
/* 8237 DMA controllers */
|
|
#define IO_DMA1_BASE 0x00 /* 8 bit slave DMA, channels 0..3 */
|
|
#define IO_DMA2_BASE 0xC0 /* 16 bit master DMA, ch 4(=slave input)..7 */
|
|
|
|
/* DMA controller registers */
|
|
#define DMA1_CMD_REG 0x08 /* command register (w) */
|
|
#define DMA1_STAT_REG 0x08 /* status register (r) */
|
|
#define DMA1_REQ_REG 0x09 /* request register (w) */
|
|
#define DMA1_MASK_REG 0x0A /* single-channel mask (w) */
|
|
#define DMA1_MODE_REG 0x0B /* mode register (w) */
|
|
#define DMA1_CLEAR_FF_REG 0x0C /* clear pointer flip-flop (w) */
|
|
#define DMA1_TEMP_REG 0x0D /* Temporary Register (r) */
|
|
#define DMA1_RESET_REG 0x0D /* Master Clear (w) */
|
|
#define DMA1_CLR_MASK_REG 0x0E /* Clear Mask */
|
|
#define DMA1_MASK_ALL_REG 0x0F /* all-channels mask (w) */
|
|
|
|
#define DMA2_CMD_REG 0xD0 /* command register (w) */
|
|
#define DMA2_STAT_REG 0xD0 /* status register (r) */
|
|
#define DMA2_REQ_REG 0xD2 /* request register (w) */
|
|
#define DMA2_MASK_REG 0xD4 /* single-channel mask (w) */
|
|
#define DMA2_MODE_REG 0xD6 /* mode register (w) */
|
|
#define DMA2_CLEAR_FF_REG 0xD8 /* clear pointer flip-flop (w) */
|
|
#define DMA2_TEMP_REG 0xDA /* Temporary Register (r) */
|
|
#define DMA2_RESET_REG 0xDA /* Master Clear (w) */
|
|
#define DMA2_CLR_MASK_REG 0xDC /* Clear Mask */
|
|
#define DMA2_MASK_ALL_REG 0xDE /* all-channels mask (w) */
|
|
|
|
#define DMA_ADDR_0 0x00 /* DMA address registers */
|
|
#define DMA_ADDR_1 0x02
|
|
#define DMA_ADDR_2 0x04
|
|
#define DMA_ADDR_3 0x06
|
|
#define DMA_ADDR_4 0xC0
|
|
#define DMA_ADDR_5 0xC4
|
|
#define DMA_ADDR_6 0xC8
|
|
#define DMA_ADDR_7 0xCC
|
|
|
|
#define DMA_CNT_0 0x01 /* DMA count registers */
|
|
#define DMA_CNT_1 0x03
|
|
#define DMA_CNT_2 0x05
|
|
#define DMA_CNT_3 0x07
|
|
#define DMA_CNT_4 0xC2
|
|
#define DMA_CNT_5 0xC6
|
|
#define DMA_CNT_6 0xCA
|
|
#define DMA_CNT_7 0xCE
|
|
|
|
#define DMA_PAGE_0 0x87 /* DMA page registers */
|
|
#define DMA_PAGE_1 0x83
|
|
#define DMA_PAGE_2 0x81
|
|
#define DMA_PAGE_3 0x82
|
|
#define DMA_PAGE_5 0x8B
|
|
#define DMA_PAGE_6 0x89
|
|
#define DMA_PAGE_7 0x8A
|
|
|
|
/* I/O to memory, no autoinit, increment, single mode */
|
|
#define DMA_MODE_READ 0x44
|
|
/* memory to I/O, no autoinit, increment, single mode */
|
|
#define DMA_MODE_WRITE 0x48
|
|
/* pass thru DREQ->HRQ, DACK<-HLDA only */
|
|
#define DMA_MODE_CASCADE 0xC0
|
|
|
|
#define DMA_AUTOINIT 0x10
|
|
|
|
|
|
#ifdef CONFIG_ISA_DMA_API
|
|
extern spinlock_t dma_spin_lock;
|
|
|
|
static inline unsigned long claim_dma_lock(void)
|
|
{
|
|
unsigned long flags;
|
|
spin_lock_irqsave(&dma_spin_lock, flags);
|
|
return flags;
|
|
}
|
|
|
|
static inline void release_dma_lock(unsigned long flags)
|
|
{
|
|
spin_unlock_irqrestore(&dma_spin_lock, flags);
|
|
}
|
|
#endif /* CONFIG_ISA_DMA_API */
|
|
|
|
/* enable/disable a specific DMA channel */
|
|
static inline void enable_dma(unsigned int dmanr)
|
|
{
|
|
if (dmanr <= 3)
|
|
dma_outb(dmanr, DMA1_MASK_REG);
|
|
else
|
|
dma_outb(dmanr & 3, DMA2_MASK_REG);
|
|
}
|
|
|
|
static inline void disable_dma(unsigned int dmanr)
|
|
{
|
|
if (dmanr <= 3)
|
|
dma_outb(dmanr | 4, DMA1_MASK_REG);
|
|
else
|
|
dma_outb((dmanr & 3) | 4, DMA2_MASK_REG);
|
|
}
|
|
|
|
/* Clear the 'DMA Pointer Flip Flop'.
|
|
* Write 0 for LSB/MSB, 1 for MSB/LSB access.
|
|
* Use this once to initialize the FF to a known state.
|
|
* After that, keep track of it. :-)
|
|
* --- In order to do that, the DMA routines below should ---
|
|
* --- only be used while holding the DMA lock ! ---
|
|
*/
|
|
static inline void clear_dma_ff(unsigned int dmanr)
|
|
{
|
|
if (dmanr <= 3)
|
|
dma_outb(0, DMA1_CLEAR_FF_REG);
|
|
else
|
|
dma_outb(0, DMA2_CLEAR_FF_REG);
|
|
}
|
|
|
|
/* set mode (above) for a specific DMA channel */
|
|
static inline void set_dma_mode(unsigned int dmanr, char mode)
|
|
{
|
|
if (dmanr <= 3)
|
|
dma_outb(mode | dmanr, DMA1_MODE_REG);
|
|
else
|
|
dma_outb(mode | (dmanr & 3), DMA2_MODE_REG);
|
|
}
|
|
|
|
/* Set only the page register bits of the transfer address.
|
|
* This is used for successive transfers when we know the contents of
|
|
* the lower 16 bits of the DMA current address register, but a 64k boundary
|
|
* may have been crossed.
|
|
*/
|
|
static inline void set_dma_page(unsigned int dmanr, char pagenr)
|
|
{
|
|
switch (dmanr) {
|
|
case 0:
|
|
dma_outb(pagenr, DMA_PAGE_0);
|
|
break;
|
|
case 1:
|
|
dma_outb(pagenr, DMA_PAGE_1);
|
|
break;
|
|
case 2:
|
|
dma_outb(pagenr, DMA_PAGE_2);
|
|
break;
|
|
case 3:
|
|
dma_outb(pagenr, DMA_PAGE_3);
|
|
break;
|
|
case 5:
|
|
dma_outb(pagenr & 0xfe, DMA_PAGE_5);
|
|
break;
|
|
case 6:
|
|
dma_outb(pagenr & 0xfe, DMA_PAGE_6);
|
|
break;
|
|
case 7:
|
|
dma_outb(pagenr & 0xfe, DMA_PAGE_7);
|
|
break;
|
|
}
|
|
}
|
|
|
|
|
|
/* Set transfer address & page bits for specific DMA channel.
|
|
* Assumes dma flipflop is clear.
|
|
*/
|
|
static inline void set_dma_addr(unsigned int dmanr, unsigned int a)
|
|
{
|
|
set_dma_page(dmanr, a>>16);
|
|
if (dmanr <= 3) {
|
|
dma_outb(a & 0xff, ((dmanr & 3) << 1) + IO_DMA1_BASE);
|
|
dma_outb((a >> 8) & 0xff, ((dmanr & 3) << 1) + IO_DMA1_BASE);
|
|
} else {
|
|
dma_outb((a >> 1) & 0xff, ((dmanr & 3) << 2) + IO_DMA2_BASE);
|
|
dma_outb((a >> 9) & 0xff, ((dmanr & 3) << 2) + IO_DMA2_BASE);
|
|
}
|
|
}
|
|
|
|
|
|
/* Set transfer size (max 64k for DMA0..3, 128k for DMA5..7) for
|
|
* a specific DMA channel.
|
|
* You must ensure the parameters are valid.
|
|
* NOTE: from a manual: "the number of transfers is one more
|
|
* than the initial word count"! This is taken into account.
|
|
* Assumes dma flip-flop is clear.
|
|
* NOTE 2: "count" represents _bytes_ and must be even for channels 5-7.
|
|
*/
|
|
static inline void set_dma_count(unsigned int dmanr, unsigned int count)
|
|
{
|
|
count--;
|
|
if (dmanr <= 3) {
|
|
dma_outb(count & 0xff, ((dmanr & 3) << 1) + 1 + IO_DMA1_BASE);
|
|
dma_outb((count >> 8) & 0xff,
|
|
((dmanr & 3) << 1) + 1 + IO_DMA1_BASE);
|
|
} else {
|
|
dma_outb((count >> 1) & 0xff,
|
|
((dmanr & 3) << 2) + 2 + IO_DMA2_BASE);
|
|
dma_outb((count >> 9) & 0xff,
|
|
((dmanr & 3) << 2) + 2 + IO_DMA2_BASE);
|
|
}
|
|
}
|
|
|
|
|
|
/* Get DMA residue count. After a DMA transfer, this
|
|
* should return zero. Reading this while a DMA transfer is
|
|
* still in progress will return unpredictable results.
|
|
* If called before the channel has been used, it may return 1.
|
|
* Otherwise, it returns the number of _bytes_ left to transfer.
|
|
*
|
|
* Assumes DMA flip-flop is clear.
|
|
*/
|
|
static inline int get_dma_residue(unsigned int dmanr)
|
|
{
|
|
unsigned int io_port;
|
|
/* using short to get 16-bit wrap around */
|
|
unsigned short count;
|
|
|
|
io_port = (dmanr <= 3) ? ((dmanr & 3) << 1) + 1 + IO_DMA1_BASE
|
|
: ((dmanr & 3) << 2) + 2 + IO_DMA2_BASE;
|
|
|
|
count = 1 + dma_inb(io_port);
|
|
count += dma_inb(io_port) << 8;
|
|
|
|
return (dmanr <= 3) ? count : (count << 1);
|
|
}
|
|
|
|
|
|
/* These are in kernel/dma.c because x86 uses CONFIG_GENERIC_ISA_DMA */
|
|
#ifdef CONFIG_ISA_DMA_API
|
|
extern int request_dma(unsigned int dmanr, const char *device_id);
|
|
extern void free_dma(unsigned int dmanr);
|
|
#endif
|
|
|
|
/* From PCI */
|
|
|
|
#ifdef CONFIG_PCI
|
|
extern int isa_dma_bridge_buggy;
|
|
#else
|
|
#define isa_dma_bridge_buggy (0)
|
|
#endif
|
|
|
|
#endif /* _ASM_X86_DMA_H */
|