Add nodes for McASP0 and McASP1 for AM43xx.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add imx6sl support into imx_init_revision_from_anatop(), so that it can
be used to initialize cpu type and revision on imx6sl.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The generic PHY framewrok expects different properties than the
old USB PHY framework. Supply those properties.
Fixes USB OTG port on beagle after the Generic PHY framework was
merged in greg/usb-next. [1]
[1] - https://lkml.org/lkml/2013/9/27/581
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
AM335x EVM-SK have only support for audio playback (stereo jack on the
board) via tlv320aic3106 codec connected to McASP1.
Enable the support for audio playback on the board:
- McASP1 configuration
- tlv320aic3106 configuration
- Machine driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This patch adds a second tuple to reg property. The new property tuple
describes the memory location for data port registers mapped trough
L3 bus on am33xx. The both property tuples are named accordingly in
the reg-names property.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
-> Adding pinmux for cpsw, i2c0.
-> Enabling the modules that are present in AM4372 EPOS EVM
These modules are tested on AM4372 EPOS EVM.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Populate nodes for l2-cache-controller, EDMA, mailbox,
mmc, sham.
Update as well DT properties for epwmss, aes, des.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Added dr_mode property in dwc3 and set its default mode to device.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
smps10 should be enabled only in the case of host mode. So stop
doing always_on, boot_on from smps10_out1. The driver will enable
it in host mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Do not reset GPIO1 at boot-up because GPIO 7 in GPIO1 block is used on
OMAP4460 PandaBoard-ES to select voltage register in TPS62361 which
supplies VDD_MPU.
Without this, OMAP4460 PandaBoard-ES boards fail to boot-up because
MPU voltage switches over to VSET0 voltage value (boot voltage) which
is not sufficient to operate the device at OPP100.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Do not reset GPIO0 at boot-up because GPIO0 is used
on AM335x EVM-SK to control VTT regulators on DDR3.
Without this EVM-SK boards fail to boot-up because
of DDR3 corruption.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
On OMAP we have co-processor IPs, memory controllers,
GPIOs which control regulators and power switches to
PMIC, and SoC internal Bus IPs, some or most of which
should either not be reset or idled or both at init.
(In some cases there are erratas which prevent an IP
from being reset)
Have a way to pass this information from DT.
Update the am33xx/omap4 and omap5 dtsi files with the
new bindings for modules which either should not be
idled. reset or both. A later patch would cleanup the
same information that exists today as part of the hwmod
data files.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The generic PHY framewrok expects different properties than the
old USB PHY framework. Supply those properties.
Fixes USB OTG port on GAT04 and N900 after the Generic PHY framework was
merged in greg/usb-next. [1]
[1] - https://lkml.org/lkml/2013/9/27/581
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The arm arch timers frequency are now programmed in the CNTFREQ
per-cpu register by the timer code using the secure API [1].
So remove the redundant entry from the dts.
[1] http://marc.info/?l=linux-omap&m=138139106312786&w=2
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
omap3 boards.
Note that that these are based on a merge of the
following for the dependencies:
- v3.12-rc5 for fixes to pinctrl mask
- omap-for-v3.13/dt-signed to avoid pointless merge conflicts
- omap-for-v3.13/quirk-signed for legacy pdata handling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=9Iuv
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/board-removal-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Changes needed to drop legacy booting support for some
omap3 boards.
Note that that these are based on a merge of the
following for the dependencies:
- v3.12-rc5 for fixes to pinctrl mask
- omap-for-v3.13/dt-signed to avoid pointless merge conflicts
- omap-for-v3.13/quirk-signed for legacy pdata handling
* tag 'omap-for-v3.13/board-removal-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (125 commits)
ARM: OMAP2+: remove legacy support for IGEP boards
ARM: OMAP2+: Remove legacy support for zoom platforms
ARM: OMAP2+: Remove legacy booting support for omap3 EVM
ARM: OMAP2: delete board-rm680
ARM: dts: add minimal DT support for Nokia N950 & N9 phones
ARM: dts: Add basic support for zoom3
ARM: dts: Add basic support for TMDSEVM3730 (Mistral AM/DM37x EVM)
ARM: dts: Add common support for omap3-evm
ARM: dts: Shared file for omap GPMC connected smsc911x
+Linux 3.12-rc5
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add minimal DT support for Nokia N950 & N9 phones. The same functionality
that is provided by the current board file should work: serial console,
USB, OneNAND and MMC.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I've tested serial, MMC, smsc911x and wl12xx on zoom3. As my
omap is an early ES revision, I have not been able to test
off-idle on this one. But anyways, I'd say we have enough
device tree support for the zoom to be able to drop the
board-zoom files. Patches are welcome to add further features
to this .dts file.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The imx6sl iomuxc syscon is compatible to imx6q, so let's add
compatible string 'fsl,imx6q-iomuxc-gpr' for imx6sl iomuxc syscon node.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- addition of sound for at91sam9n12
- a little fix for MMC vs. SPI on at91sam9g20ek
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSYUtRAAoJEAf03oE53VmQH+EH/1YhBDF7uL5s+TCKLBOyau+G
i+W93uG4acZAdbUMRwY+/dP5HMwFu5ZSoKDD5LoRnG2O+jW5dB3rBPi1C42XRKa/
ra1wQcabKFPERJGDJ8DWbuLoJ7WNiDNENDa5ckV3m+F7dRbflcNyUB7vPUiGW78c
xe/WKCKB9Hhpytl1fAynRs+VEu/z3hW7KV7QFyVDatOtV11Vb4QSSJ5HjfMhfito
T7zAsML26hIdcNRsDQs8/4Uwgy8Tevl6FbtLHvht18BJB7FSxRtiPrAGh0KAmwsl
HwIT8RzgJqdDlXTi9z9BdLFlvFZkX83n12jrB7hGScOKav45kvmmC9pgwhFbRzk=
=uw6I
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
First DT series for 3.13
- addition of sound for at91sam9n12
- a little fix for MMC vs. SPI on at91sam9g20ek
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: remove pinctrl conflict between mmc and SPI for at91sam9g20ek
ARM: at91: add sound support on at91sam9n12ek board
ARM: at91: enable ssc on at91sam9n12ek board
ARM: at91: enable wm8904 on at91sam9n12ek board
ARM: at91: add ssc dma parameter for at91sam9n12
ARM: at91: add at91sam9n12 ssc clock in look up table
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- a little non-urgent fix
- addition of DT files to MAINTAINERS
- more important, the splitting of .dtsi files
that allows to precisely choose the peripherals
that are present for a particular SoC.
It is useful for upcoming move to common cloks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSYT2LAAoJEAf03oE53VmQfRMIAIgFQruxaCTlhpvdZaEyDeIK
6+szV0Nn9irQyZqe2HvUR6Flb7FfmAGiyS0xj/OY4bEBbCOeau8Df/op3fVa6+Q2
t510ricL9OWaSqaIsKgJqk3mjpq/7jMrXBQzBjQFgKVcJSA+zOJNiB6qabmE9KjY
z/2+hYaBgG7WwWffHmJQ34NYrIqrWbqaGZczxY9IVw7i4kfDXPL2t2JZk2JTwstt
4C4CRxKXx27EMF0gE2BOgH0r1euaqllSg4ogYlQkBn2canylvNYiRN2Eu36g4peE
cGjtW/8R0ngz3udeoQWeHZ+nZoFT15m048xgIOUbxX5Ocy7u7HSL0tbaH+W9ciI=
=VlMj
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup' of git://github.com/at91linux/linux-at91 into next/cleanup
From Nicolas Ferre:
First cleanup series for 3.13
- a little non-urgent fix
- addition of DT files to MAINTAINERS
- more important, the splitting of .dtsi files
that allows to precisely choose the peripherals
that are present for a particular SoC.
It is useful for upcoming move to common cloks.
* tag 'at91-cleanup' of git://github.com/at91linux/linux-at91:
MAINTAINERS: Add patterns for DTS files for AT91
ARM: at91: remove init_machine() as default is suitable
ARM: at91/dt: split sama5d3 peripheral definitions
ARM: at91/dt: split sam9x5 peripheral definitions
ARM: at91: cam60: fix incorrect placement of __initdata tag
These MMC and SPI buses can't be configured at the same time because they
share the same traces on the EK board.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
From Heiko Stübner:
Support for the RK3188 SoC, basic RK3188 based Radxa Rock board
and RK3066a based BQ Curie2 tablet.
* rockchip/boards:
ARM: rockchip: add support for rk3188 and Radxa Rock board
ARM: rockchip: add dts for bqcurie2 tablet
ARM: rockchip: enable arm-global-timer
ARM: rockchip: move shared dt properties to common source file
This adds the SSP and SPI blocks to the device tree and makes
them active. Only this way can their clocks be properly gated
off at boot.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PCLK for I2C4 is controlled by bit 10 in the PCKEN registers
while the KCLK is controlled by bit 9 on the KCKEN, it's
one of these odd assymetric things. Correct the PCLK bit to 10.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The clock assignment in the device tree for GPIO blocks 6
and 7 was incorrect, indicating this was managed by bit 1 on
PRCC 2 while it was in fact bit 11 on PRCC 2.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The clock assignment in the device tree for GPIO block 8 was
incorrect, indicating this was managed by bit 1 on PRCC 6
while it was in fact bit 1 on PRCC 5.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
add a pinctrl for ECSPI1. This pinctrl can be used in the imx6sl-evk board.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The pwm-node is missing its #pwm-cells property. The pwm-framework will
complain about this.
Add the missing property.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
From Stephen Warren:
* tegra/dt:
ARM: tegra: Use symbolic names for gr3d clocks
ARM: tegra: Mark Tegra30 display controller compatible with Tegra20
ARM: tegra: add GPIO controller to tegra124.dtsi
ARM: tegra: enable LP1 suspend mode for Venice2
ARM: tegra: enable Tegra RTC as default for Tegra124
ARM: tegra: add Venice2 board support
ARM: tegra: Add initial device tree for Tegra124
ARM: tegra: add vcc supply for nct1008 to Cardhu
ARM: tegra: add DT entry for nct1008 to Dalmore
ARM: tegra: use dt-binding header for key code
ARM: tegra: add palmas pincontrol to Dalmore device tree
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- convert Calxeda cpuidle driver to a platform driver and to use PSCI
- convert highbank smp_ops and suspend to PSCI
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSYCG/AAoJEMhvYp4jgsXiFkkIALhWCtYC7qcthorB/s9STVkv
5VhPA7Jx9i9omnrsdzICXYC/HQaSN7gwgAPICYxTcAcen+qySHeXvk7jWh7PtQJ9
OHLWd1tYVxLV1y9tnmiFYVbJn017W0Kq0m4kkZEh6Q8KW0qE1xcHGREWHs/+1D4k
Rx798Tg6jgjt0nvg893aAcFQsgKxG53n5uqNySI9DKvxYcJBJkHD0/EgyHk+myVY
TPZj6f9xGwLCv0rQU6Vr29NniX1w2bRt6lYEp0KGlGjEGbiuStcRf6xUUmhxmDCs
faIspFMxpR4dqqeIq1Xh2x8S4QOMjDoiFGZmGBgrNdvLNOGNsd+QRhdLJiXuB88=
=8WVt
-----END PGP SIGNATURE-----
Merge tag 'highbank-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into next/soc
From Rob Herring:
Highbank platform updates for 3.13
- convert Calxeda cpuidle driver to a platform driver and to use PSCI
- convert highbank smp_ops and suspend to PSCI
* tag 'highbank-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dts: calxeda: add ARM PSCI binding
ARM: highbank: adapt to use ARM PSCI calls
ARM: PSCI: remove unnecessary include of arm-gic.h
cpuidle: calxeda: add support to use PSCI calls
ARM: highbank: cpuidle: convert to platform driver
cpuidle: calxeda: add cpu_pm_enter/exit calls
- dove
- add audio devices
- fix bad properties of si5351 clkout2 for CuBox
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJSX+yTAAoJEAi3KVZQDZAev1wIAJA521UnQR6efGNEU6wD3Yvq
hjXEe+Da62FG2YUzZhOpLYIRrc0EvTrt/JIAbLbf5qrOnc9kzO6YdZVnRJJgWDP0
Qzak9C0xqfsFeR7MxnDuyJ10/TYgM1iugvUcs6tqRDb7LdqcGBv92vv8zCdieiiJ
XNtA56GVvEXo6LKp4KjC/dNv4vQBPEzDukSm81g/dfVDIhm7vbGMeNpFtHPHcNQa
lASc6NjYzZXBZlz/ckRIZeT+MePpPkWusb8DOtLkv6/pRJjtSLaQqSLR82l52U+E
eVb9SoQJWjxmrVLMEk3nUYvsWVgLtClND62snfpu+JP5ELb+DBwky4DzVvftpaY=
=P7l9
-----END PGP SIGNATURE-----
Merge tag 'dt-3.13-3' of git://git.infradead.org/linux-mvebu into next/dt
From Jason Cooper:
mvebu dt changes for v3.13 (round 3)
- dove
- add audio devices
- fix bad properties of si5351 clkout2 for CuBox
* tag 'dt-3.13-3' of git://git.infradead.org/linux-mvebu:
ARM: Dove: fix bad properties of the si5351 clkout2 used by Cubox audio
ARM: Dove: Add the audio device to the Cubox DT
ARM: Dove: Add the audio devices in DT
Some small cleanups for MSM. Removes extraneous irq definitions that
aren't used on DT targets, moves the single existing board file to
board-dt.c in antipication of additional targets, and renames the
existing DT files to have a common 'qcom' prefix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=xAJK
-----END PGP SIGNATURE-----
Merge tag 'msm-cleanup-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup
From David Brown:
General cleanups for MSM for 3.13
Some small cleanups for MSM. Removes extraneous irq definitions that
aren't used on DT targets, moves the single existing board file to
board-dt.c in antipication of additional targets, and renames the
existing DT files to have a common 'qcom' prefix.
* tag 'msm-cleanup-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Rename msm devicetrees to have standard 'qcom' prefix
ARM: msm: Create a common board-dt and config ARCH_MSM_DT
ARM: msm: Remove irqs-*.h files for DT based targets
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- Fix up the LED support
- Update the Integrator defconfig
- Remove ATAG boot path
- Move some stuff over to the device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=p2Z9
-----END PGP SIGNATURE-----
Merge tag 'integrator-for-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/soc
From Linus Walleij:
Integrator patches for the v3.13 kernel cycle:
- Fix up the LED support
- Update the Integrator defconfig
- Remove ATAG boot path
- Move some stuff over to the device tree
* tag 'integrator-for-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: core module registers from compatible strings
ARM: integrator: use devm_ioremap() to remap CM
cpufreq: probe the Integrator cpufreq driver from DT
ARM: integrator: move CM base into device tree
ARM: integrator: decommission the <mach/irqs.h> header
ARM: integrator: delete non-devicetree boot path
ARM: integrator: print the Linux IRQ in LL_DEBUG code
ARM: integrator: get the LM interrupts from DT
ARM: integrator: update defconfig
ARM: integrator: get the CM control register by proxy
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Commit 05849c9381 (ARM: tegra30: convert
device tree files to use CLK defines) updated the Tegra30 device tree to
use symbolic clock names but forgot to update this node.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The display controller found on Tegra30 SoCs is backwards-compatible
with the one on Tegra20 SoCs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch splits the sama5d3 SoCs definition:
- a common base for all sama5d3 SoCs (sama5d3.dtsi)
- several optional peripheral definitions which will be included by sama5d3
specific SoCs (sama5d3_'periph name'.dtsi)
- sama5d3 specific SoC definitions (sama5d3x.dtsi)
This provides a better representation of the real hardware (drop unneed
dt nodes) and avoids peripheral id conflict (which is not the case for
current sama5d3 SoCs, but could be if other SoCs of this family are
released).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
[nicolas.ferre@atmel.com: add more "sama5d3?" compatibility strings]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch splits the sam9x5 peripheral definitions into:
- a common base for all sam9x5 SoCs (at91sam9x5.dtsi)
- several optional peripheral definitions which will be included by specific
sam9x5 SoCs (at91sam9x5_'periph name'.dtsi)
This provides a better representation of the real hardware (drop unneeded
dt nodes) and avoids future peripheral id conflict (lcdc and isi both use
peripheral id 25).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This augments the core machine code for the Integrator platforms
to get their references to the core module device nodes by
using compatible strings instead of predefined node names
and rename the CP syscon node to be simply "syscon".
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the core module (CM) control base into the device
tree. It is a simple memory range of 0x200 bytes. Move the
cm header down into the machine directory and unexport the
cm_control() symbol as no modules are using it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The OF/DT boot path needs to get the LM (Logical Module)
IRQs from the device tree for coherency. This augments the
DT syscon node to contain these IRQs and alter the DT LM
code to get them from there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Revision 0 of Exynos4210 SoC (used on Universal C210 board) requires
'secure' PL330 MDMA1 address (0x12840000) instead of 'non-secure' one
(0x12850000). Fix it by overriding the default PL330 MDMA1 address in
exynos4210-universal_c210.dts.
This is a Device Tree (DT) version of commit 91280e7 ("ARM: EXYNOS:
PL330 MDMA1 fix for revision 0 of Exynos4210 SOC") and fixes recent
regression caused by conversion to DT-only setup on ARM EXYNOS.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos cpufreq drivers does not support device tree based regulator
lookup, so it can get the VDD ARM regulator only by its name. To get
cpufreq working for now, this patch works this around by renaming the
regulator in board dts files to vdd_arm, which is the name expected by
the driver.
This fixes a regression introduced by dropping support of board file
based bootup of Exynos 4210 boards that rendered cpufreq inoperable on
Trats and Origen boards.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes '_' from "early_prink" on Exynos5440 dts
files in according to kernel-parameters document.
Signed-off-by: Youngmin Nam <youngmin.nam@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Jungseok Lee <jays.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
